creality ender 3 voltage 3d models

This is an alternative camera attachment for the Ender 3, which must be used in conjunction with a specific support arm from Thingiverse: https://www.thingiverse.com/thing:2886101. It's also compatible with Pi Camera V2 or V2.1 models, but users of...

Motherboard cover for Ender 3 PRO Only. Silent et best cooling. I had to make one to get a proper cooling and ultra silent 80mm fan 10mm 12v This cover is 10mm so you need to print Feet that raise you printer. I've done mine with 20mm + rubber...

Here is the spun text: I recently created a sleek and functional LED-strip light bracket for my Crealty Ender 3. ... As you can see from the pictures, the following parts are required to assemble it: * 2 x LED Beam 1 * 2 x LED Beam 2 * 2 x Bracket...

This is just a basic bracket used to mount BMG extruders on Ender 3 printers. ... ---------------------------------------- Required Materials: BMG Extruder - Aliexpress M3x8mm Cap Head Bolts (4) M3 Locknuts (4) M3x40mm Cap Head Bolts (3) M3x6mm Cap Head...

Led bar mount for any creality 3d printer.I used 24V LED strip with a length of 26cm.

Simple and low profile clips for Creality glass bed probably works with others too. ... You can use ABS or PetG.

white types with a forward voltage of 3 to 3.3-volts, eliminating the need for current limiting resistors. They are connected using strip Veroboard, ensuring a secure soldering process. A 1.5" sq. mirror is held in place by double-sided tape and can...

This is a simple strip to set inside the Ender 3 frame to keep it clean.I printed a fan cover because I heard lots of debris would come from printing. This turned out to be true and I noticed the plastic scraps still got into some other crevices, so...

I found this so helpful at getting the perfect first layer setup that I found myself using for all different types of materials - I have now remixed it for use on my Ender 3.In Summary, you adjust your babystep Z during the print until you get a good...

With the extra T-nuts provided with my Ender 3 and some M4 x 8mm bolts at my disposal, one of which was more than sufficient in terms of strength, I decided to opt for the snap-fit design instead. ...The open bolt-on version and the open snap-on version...

I used this part as a filament guide for my Ender 3 printer. Its purpose was to protect the inlet of the extruder from wear caused by the filament rubbing against it. I had an extra 22mm OD, 8mm ID, and 7mm wide skate bearing that served perfectly as...

Fortunately, my Ender 3 printer features a removable bed that came equipped with paper clips. However, I wasn't impressed with them. They proved difficult to remove, and if the hotend encountered them, they were too rigid and wouldn't budge. ...In...

I'm planning on printing Teaching Techs Ender 3 Electronics Case (https://www.thingiverse.com/thing:3688967) which would leave a void where the factory electronics case sits. This remix is designed to compliment the v2 case which sits flush to the...

I was fed up with fiddling around with spacers and similar components so I lost the spring for my extruder, therefore I decided to utilize a leftover M5 bolt from the Ender 3 kit along with all of the hardware present in the stock extruder arm. P.S....

Here's my Sudomod Logo Ender 3 X-axis QR code cover. I designed this to hide the annoying sticker and give my printer a nicer look. Works great! Prints fast. Clips right on! I have a BitBuilt version as well. I also modified this to be a Minty...

Use one hand to change the Ender 3's filament with ease by following these simple steps. Start by slipping a large rectangular piece over the extruder tension arm, then squeeze it tight to release the grip on the old filament. Next, slide the small...

The cover effectively conceals the ribbon cable of my Ender 3, keeping it tidy and out of sight. Given that this is my first try, the fit is a bit snug, which could be improved upon. ...To help others work with this design, I've also included SKP files...

This is a simple strip to set inside the Ender 3 frame and keep it clean. I printed a fan cover because I'd heard that lots of debris would come from printing, and this turned out to be true. The plastic scraps still got into some other crevices, so...

Here's my revised Sudomod Logo Ender 3 X-axis QR code cover design. I created this to conceal the bothersome sticker and give my printer a more attractive appearance. The design works perfectly! Prints swiftly. Clips into place flawlessly! I also...

---------------------------------------- **My Other Ender 3 Parts:** [Tusk Fan Shroud](https://www.thingiverse.com/thing:3055926) [Z Endstop Bracket](https://www.thingiverse.com/thing:3057136) [Y Endstop...

A mount for the creality filament run out sensor which does not mean taking the whole Z Axis apart!4 x M3 x 16 nuts and M3 bolts required for the sensor to mount to the plate. Printed on 0.20 layer height with PLA.</p><p>This is a remix, but I have...

Otro portaherramienta para Ender pero con portausb y porta microsd mas un compartimento extra

This is a remix or redesign of the https://www.thingiverse.com/thing:3700643 "Creality Ender Station (LCD + Raspberry Pi)" I have added a side console for a power switch and a status LED for the Raspberry and moved the base for the camera mount to...

This is a remix or redesign of the https://www.thingiverse.com/thing:3700643 "Creality Ender Station (LCD + Raspberry Pi)" I have added a side console for a power switch and a status LED for the Raspberry and moved the base for the camera mount to...

Check out this awesome Creality Extruder knob you can find on YouTube by watching the video at https://www.youtube.com/watch?v=efzIjb2p6R4.

The Creality 3D Pro's wire guide is outshined by this fantastic option, consistently keeping the filament tightly wound without ever compromising the extruder motor.

While making my first prints on the Ender-3 V2 the cable that runs to the nozzle got stuck between the print bed and the motor that is situated in the rear of the printer. To prevent this from happening I designed this cable holder. To attach the...

As an avid fan of the iconic motorcycle brand, I decided to give my Ender 3 printer a unique touch by designing a custom fan cover that proudly displays the distinctive Harley-Davidson logo. The result is a one-of-a-kind accessory that not only...

Despite the Ender 3 having possibly the best printing surface I've ever used, I have had a few prints lift at the front left corner. It's unclear whether it's definitely the board fan pulling air on the underside of the bed, but it can't help. I...

...I must thank @Shenkoe for his amazing troubleshooting guide for the Ender 3 and also releasing his own versions of my profile. Unfortunately, I've lately been struggling with issues on Thingiverse and have decided to relocate the file download here.