creality ender 3 v2 dual extruder 3d models

... and the pulley. Gold is the short version (v1) Gray High Clearance / Extended version (v2) Print Settings Printer Brand: Creality Printer: CR-10 Rafts: No Supports: No Resolution: 0.2 Infill: 15% Notes: K-Camel PLA 210/60 Category: 3D Printer Parts

Here is a remix of the 'filament_detector_arm_coupling' from https://www.thingiverse.com/thing:5237906 I loved this design but the mount did not fit my Creality brand runout sensor. The only difference between these two files is the orientation of...

This spool clip will hold it into place as far as possible from the extruder, leading to a larger angle for the material to enter the extruder gear. Works quite well for me. I do not remove it from the spindle, find it easier to undo the plastic...

You may want to upscale it by 0.5-2% Update 01/03/2018 V2 High Clearance / Extended version Added a high clearance version so you can check the filament rolling between the gear and the pulley. Gold is the short version (v1) Gray High Clearance /...

I wanted my spool holder to be able to hold 3 500g spools for easy color switching. ...This extension just slides in the original spool holder with a tight fit and extends it by 35mm.

... bolts, just enough to hold it tight. I have added some holes and a channel to keep the web cam wire tight and neat, and the hole in the bottom is to place the web cam wire through.The top hole is big enough for a 3/8 bolt which fits most web cams.

I was thoroughly impressed by DMRS3's ingenious design, which prompted me to envision and build upon it with a dual version tailored specifically for my setup, as I happen to have two distinct cable groups connecting directly to my hotend.

... fine. A second issue was that my printer would NOT print the center leg at the bottom of part 2. I tried 3 times and it would always just snap off at the same point (during printing no less) so I removed the curves and added a straight post.

I wanted to upgrade my Creality CR-10 by adding a dual nozzle (extruder) to print ninja flex and either PLA or ABS at the same time. I sourced a Reprap dual nozzle from eBay, available here:...

... upgraded to V2 High Clearance / Extended version. This new design allows me to check the filament rolling between the gear and the pulley. The Gold knob is the short version (v1), while the Gray knob is the High Clearance / Extended version (v2).

Bracket used to align the Filament Runout Sensor with the Micro Swiss Dual Gear Bowden Extruder that is being installed on one of the 3D printers listed below.Compatible with:Ender 3 MaxEnder 3 Max NeoEnder 5 PlusCR-10 V2Use two of the four screws to...

I made the model to adapt it to ender 3 or pro. ... You'll have to cut 1cm from the chassis to better route the cables, then also on the power button.

Hello to all, I was fed up with my spool getting stuck during the printing process because the original position on the top is not optimal, the filament has to make a more or less tight curve (depending on the height of the Z) to enter the...

A mount for the creality filament run out sensor which does not mean taking the whole Z Axis apart!4 x M3 x 16 nuts and M3 bolts required for the sensor to mount to the plate. Printed on 0.20 layer height with PLA.</p><p>This is a remix, but I have...

Heart shaped extruder valve for Ender 3/V2/PRO

... allow for a bit of variation between different brands of bottles. This will slide right into the top frame rail above the posts on Ender 3 and Ender 3 Pro printers. Will probably fit others as well if they use the same frame rail notching. ...

This is a simple, lightweight and modular cooling system designed specifically for Creality 3D printers with Micro Swiss hotends, including CR-10 and Ender models. The system consists of two key components: a base plate that doubles as a hotend...

Replacement of the ender 3 v2 extruder lever with double security on the wheel.

DIY Creality Ender 3 / Ender 3 Pro / Ender 5 / Cr-10 Extruder Knob.

Sunhokey filament sensor holder for Creality Ender 3 V2. ...This revision extends the mounting length so it will hold stronger.

Sunhokey filament sensor holder for Creality Ender 3 V2. ...This revision extends the mounting length so it will hold stronger.

A dual spool holder for the Ender 3 S1 Pro v2. Made for twice the efficiency. ...What more did you expect from the name?

Remixed from https://www.printables.com/model/270817-ender-3-v2-extruder-cable-guide Supports needed. ... It's very tight

Extruder Knob for the Creality Ender 3 Printer / Ender 3 Pro Upgrade / CR-10 V3 Replacement

This is to relocate the Extruder out of the way of the z axis rod and allow an all metal extruder to clear a Pivot Arm based Bowden tube.Also allows for a dual extruderHardware for this piece:Mounting to the nema mount:x4 M3 x 16mm screws +...

Install a custom skin on your Ender 3 by overlaying the Creality Dragon design onto the existing QR code panel, utilizing a dual-color print job to achieve a striking visual effect.

Added an overlay cap to the extruder knob on my Ender-3 v2 to remind me which direction to turn the knob. ...

... for the extruder: One M3 x 10 screw for under the arm mount hole One M3 x 20 screw for arm pivot hole Two M3 x 25 screws for the raised extruder mounts. 2018-11-01 - added dual extruder relocator per request, please feel free to give feedback!

Use this model if you have problems with aligning the lead screw. https://www.printables.com/model/635002-ender-3-dual-z-axis-upgrade/ This is a bundled STL package to upgrade your Ender 3/Ender 3 Pro/Ender 3 V2 printer to use dual z-axis. All the...

I needed a dual Z bracket for my Ender 3 V2, but without the need of extra hardware for mounting it. The only extra hardware needed is the nut for the leadscrew. ... The model is oriented so it does not need supports.