creality ender 3 upgrade 3d models

This is a remix for the Ender 3 v1 (not pro) printer. ... Also included a 15mm shorter version as the extended version is a tight fit and doesn't accomodate lcd ribbon clips.

ENDER 3 PRO SETUP AND IMPROVEMENTS https://www.youtube.com/watch?v=wUEyVB6nFYo SUBSCRIBE!! ...FILAMENT SPOOL HOLDER: https://www.thingiverse.com/thing:4765789 BEARINGS/RODAMIENTOS: http://amzn.eu/d2HUwX9 THREADED ROD https://amzn.to/2Ntshi6 ...

This is Creality 3D printer - miniature, home decoration

... connected it to the USB hub. I attempted to print it on my Ender 3 but ended up printing on my Elegoo Mars because I was unable to achieve the right clearance fit on the Ender 3. ... Currently, my Wyze Cam is plugged in and functioning flawlessly.

Creality Ender alignment prints for digital gauge. These are the Companion models to this video: https://youtu.be/AN0MlQMMew0 Given that the models are structural yet not specifically load-bearing, I printed the gauge holder in Cura with 0.32mm...

Tool holder for Ender 3 stock tool - no extra screw required. Small tool in front, large one behind. Cutting pliers and other tools are securely held due to a height of 20mm. This measurement matches the horizontal profile exactly. ... The tool holder...

This is a simple solution to the black hole over the micro sd card slot in the ender 3. If the card has been swallowed multiple times by the machine. ... It's enough to print it and insert it into the location above the SD card.

...... I conceived a fundamental Power Supply Cover for the Ender 3, which also muffles the PS-FAN and redirects hot air upwards. ... Note: The inner wall is excessively high and thin, causing it to wobble during printing, so I simply chopped it off after.

This is a variation of my Filament-Cutter design specially for the Ender-3-Pro in conjunction with an MicroSwiss hotend.The Filament-Cutter is being used in my SMuFF project in order to get rid of the ramming while swapping filaments.

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

This is a variation of my Filament-Cutter design specially for the Ender-3-Pro in conjunction with an MicroSwiss hotend.The Filament-Cutter is being used in my SMuFF project in order to get rid of the ramming while swapping filaments.

On Creality printers (at least the Ender 3), the cooling fan in the electronics is coupled with the part-cooling fan, so make sure to turn that on (M106 S255) to avoid overheating your printer electronics while plotting. You may or may not include...

... screws on top of the main electronics cover. Once all obstacles were cleared, I could slip the final foot into its designated slot within the aluminum frame. The entire printing process took less than two hours to complete on my Ender 3 printer.

______________________________________________________________________ This is a remix of the handle included in this Thingiverse item: Ender 3 bed handle with removable Raspberry Pi camera mount by PatriceLoco -...

While making my first prints on the Ender-3 V2 the cable that runs to the nozzle got stuck between the printbed and the motor that is situated in the rear of the printer. To prevent this from happening I designed this cable holder. The cable...

There's a version labeled "Creality" and one that isn't. ...It might work for other Creality Printers as well. The design doesn't look great with Smurf-Blue PLA, but my black PLA was all out. ...I'd love to see your prints in another color, though!

I found the original Ender 3 spool holder too short and too thin for most of my filament spools. All filaments I use have a 50mm diameter hole and a width of just over 100mm. So those spools run with more friction and are worse secured because they...

**Other Ender 3 Parts.** [Tusk Fan Shroud](https://www.thingiverse.com/thing:3055926) [Z Endstop Bracket](https://www.thingiverse.com/thing:3057136) [Y Endstop Bracket](https://www.thingiverse.com/thing:3057132) [Cable...

This is a compact cooling vent for the standard fan that comes with the Ender 3 printer. To install it, simply swap out the original fan duct with this one. For optimal results, print it from PETG due to its proximity to the hot end, but...

https://www.thingiverse.com/thing:3639454** I stumbled upon Filboyt's Ender 3 vent ring creation and was impressed, so I decided to print it out. It fit perfectly with my printer, and the 'bowl of water test' confirmed its excellent performance. So...

You must print the piece labelled ‘cable chain - link’ 15 timesI will release a video of how to install it in a week or two whenever i can.Unfortunately this doesn't work for the Ender 3 v2. This has been designed for printers that have been...

Unfortunately this doesn't work for the Ender 3 v2. This has been designed for printers that have been converted to direct drive or do not have their extruder in the same place. The only extra hardware you will need is one M6x20 bolt with a nut, it...

I am designing a new case for my Ender's power supply, electronics and screens, so I am recreating each part in Fusion 360. Thought I would share for your designs. ... If you can print this into a working model I will be highly impressed.

... M4x15. It employs an original Creality nut, which serves as a crucial component. Initially, I utilized a roller with extended functionality to catch the 10mm diameter end within a bench drill, after which I smoothed the surface using sandpaper.

For those wondering how I got this old camera working with my Raspberry Pi 3, rest assured it was a breeze - just plug in the USB cable and enable the camera settings in config. ...The fact that this is an older model (5-7 years old) made no difference...

... 45 MM in length and 15 mm in width, making it a relatively compact print. It took around 12 iterations to refine the design. Key specifications for this project include: - CAD Software: TinkerCADD - Slicer: Cura 3.6.0 - Computer: MacBook Pro

https://gulfcoast-robotics.com/collections/creality-ender-3-upgrades-and-parts/products/24v-premium-led-light-bar-upgrade-creality-ender-3-3d-printer Useful when running a dual Z screw axis to be able to simply mount the light just above everything...

DIY Creality Ender 3 / Ender 3 Pro / Ender 5 Extruder Knob. I gave this knob a hole for tightening. ... Bolt Size : M4

CREALITY ENDER 6 UPGRADE LCD 5" IPS KLIPPERSCREEN 5inch Capacitive Touch Display for Raspberry Pi, DSI Interface, 800×480 https://www.waveshare.com/5inch-dsi-lcd.htm https://www.aliexpress.com/item/1005004930844232.html https://paypal.me/pemlik

Power Button Upgrade Kit for Ender 3 by Creality