creality ender 3 pro filament 3d models

I designed a custom spool holder for 75mm hole spools, similar to those used by Geeetech, as a solution to the issue of rough rolling on my Ender 3/Pro spool holder. ...The existing design caused unpleasant loud bumps when spinning.

This is a remix of abrenoch's thing 4611661. ... I moved the position of the sensor down and away from the extruder to accommodate my X-Axis Cable Chain bracket as well as my upgraded aluminum extruder frame on my Ender 3 Pro.

With my spool holder mounted on top, the filament had a sharp angle entering the inlet, which was likely due to my Ender 3/Pro setup. I appreciated the original design's use of PTFE tube as a guide and upgraded mine accordingly. Cutting a section...

I like the Ender 3 filament guide remixed by _HAL9000_ . It is clean and stable. However I already have the dual Z and stabilisers installed so I don't want to disassemble it and set up again. So I remove a portion from the _HAL9000_ model to allow...

This is specifically for the stock spool holder on the ender 3 pro, but likely fits others or can be easily adapted. It takes a small amount of pressure to pop the clips over the lip then fits snuggly into place. To remove it, just push in on the...

Since my Ender 3 s1 pro has a filament spool rack with bearings in it i made this end-cap and spool spacer set to allow the spool to use the bearings instead of freely spin. You will need 2 spacers and 1 end-cap, Edit: complete re-write of...

Combined the runout sensor with guide by blaiseb (https://www.thingiverse.com/thing:3357097) with the attachment method of the runout sensor by murphmandan (https://www.thingiverse.com/thing:4337798) To physically attach the sensor and guide to my...

Even after the remix, it wouldn't work with the, "Creality Ender 3 V2 Angled Spool Holder Mount," by epiic, that I was already using. (https://www.thingiverse.com/thing:5686019) So, I took the two ideas and created my own dual-purpose design on...

thirsty_camel made side-entry filament guide for Ender 3 S1, but it had too much of friction when filament was pulled from drybox. I designed these addons to use the original filament guide arm.I used two Wurth 608 2RS bearings. All things is made so...

*Another mount for* - BTT smart filament sensor - for the **newer one** (molded case, not 3D printed; 3mm shorter and 2 mm narrower) - Ender 3 Pro (Ender 3 / 3 V2 could be ok, but check first the dimensions) - BMG extruder - mine is Fysetc dual gear...

I used only the insert part of the Z lead screw support to attach to the Ender 3 Pro 20 x 20 crossbeam. I also utilized the concept of protecting the Z screw from mishaps by simply creating a hole that forms a cage to prevent it from binding (with a...

He diseñado una guía de filamento para mi Ender 3 Pro, supongo que también servirá para la Ender 3, aunque yo no la he probado. Esta guía va colocada sobre el motor del eje X, solo hay que aflojar un poco el tornillo de la rueda del eje Z para...

Case moldura visor paga gabinete Ender 3 Pro Creality com suporte para Micro SD

Next, I threaded the hole precisely for a Push Fitting Connector - specifically the compact 6 MM one that came with my Ender 3 Pro. A short length of Bowden tubing was then screwed into the guide. The print was executed at a density of 5% support...

I needed a solution for 600g reels from Flashforge that have an inner diameter of only 20mm, so I came up with a quick fix. This will plug directly into the existing reel holder. Additionally, I created a replacement holder that mimics the stock...

Please use v042 for Raspberry Pi 2/3** This is an enclosure that I designed to go under the LCD display of the Creality Ender 3 Pro (probably will fit perfectly to Ender 3 too) that also holds a Raspberry Pi 2/3 and now 4. ~~Later on, upon request,...

A simple 2in1 mount for an ADXL345 on the Creality Ender 3 S1 / Plus / Pro or all Sprite extruders / Pro.

Remixed from Ender 3 Filament runout sensor and guide with bearing by blaiseb The holes on the E3Pro stock or metal replacement extruder dont line up on the original file. I removed 5mm from the middle and now its damn near perfect. Just wire in...

Creality Ender 3 Tool Holder

I printed this https://www.thingiverse.com/thing:3063886 filament guide for my Ender 3 v2, because the filament was scraping the Z lead screw sometimes. However, it's suggested to use 608 bearings with this desing and I didn't have any. Tried to...

The 3x version is installed on my ender 3 pro at the moment. I have included a new left z support frame for two stepper motors. The headers can be printed without support to prevent issue with the printed threads. The height of the hot end on the...

MBOT3D MK2_Rev2.0 (Ender7 style fan duct) by Ahmad Sunardi:https://shorturl.at/lpILV TheBuildBay version:https://shorturl.at/pqITY Whole story was about I want to upgtade my ancient Ender 3 "pro" with high flow hotend. So I found TheBuildBay's...

The stock Ender 3 Pro reel holder is rather simplistic and fitful. I searched for a better solution with bearings but not the end cap design you have to mount to the spool hub every time. I also didn’t want a 15 hr print job. I decided to use...

Improved and enhanced mount designed for Creality filament sensors. This new design enables the filament sensor to rotate freely, effectively preventing any tangling or snapping of the filament. I thoroughly searched through Thangs to find the...

Free riding on filament

This includes a cut out for the 4040 Damper legs in the front Right corner for the Ender 3 Printer.

Caution: This is explicitly designed for the Ender 3 PRO, which has a 40x40 Y axis extrusion instead of the 40x20 one of the standard Ender 3. ... ### Additional Parts (4) M3 nuts (10-12) M3 screws (2-4) M3 2020 t-nuts Optional 12mm buttons ...

Remixed filament guide to align the filament path with the Bantam Feeder - https://bantam.design/feeder

To avoid confusion, you will need to print: **Ender 3 with 4010 fan (stock version of fan):** * Ender3_case.stl * leg.stl, 3x * Ender3_cover_left_2.5mm.stl *AND* Ender3_cover_right_2.5mm.stl * OR * * Ender3_cover_left_3mm.stl *AND*...

This model mounts wifi box creality camera adn sd card to the front corner of ender 3 s1 pro