creality ender 3 pro filament 3d models

Designed to fit Ender 3/Pro existing spool tube, diameter 30mm. Edge on the tube needs to be cut off to slide the bearing on. To secure the bearing on the tube, I've drilled small hole through and put R-pin in. Might need some slight sanding on the...

3-5-2022 Filament Guide for My Ender 3 Pro. I tried several guides and none was exactly lined up straight. I created this and the bigger radius allows for you to center this up without a problem. Uses one of the stock screws for the lead screw...

Simple remix, adapted to use generic, cheap 3-pin filament detection sensor you can buy online, such as http://bit.ly/2JjjDnk Also change dimensions a little to align the filament better on my Ender 3 pro. You will have to print parts for the bearing...

Specially designed for flexible filament out of jams.

I needed a roller so that I could put the filament spool behind the printer in a filament dryer. This is a modification and merge of two projects. 1."Filament guide with roller - Ender 3" from Tomaskom.2. “Ender 3 Direct Drive Filament...

... and aluminum extrusion. WARNING I HAVE NOTICED ON MY ENDER 3 MAX THAT WHILE PRINTING AN ITEM THAT UTILIZES THE FULL ZED AXIS THAT SOME FILAMENT BINDING MAY OCCUR, i have not tested on my ender 3 pro as it is not currently setup for direct drive.

Remix of - https://www.thingiverse.com/thing:5388236 Edited the guide arm to align better with my Ender 3 Pro. Original had a tendency to have the filament rest on the edge of the guide (sometimes between the roller and the guide frame). Should fit...

A simple mount for the BigTreeTech Smart Filament Sensor for the Ender 3 Pro. Slots onto the metal bracket behind the v-slot roller for the z-axis. This replaces the backplate of the sensor. It can be removed by removing the 6 screws on the back.

ENGLISH: I have designed a filament guide for my Ender 3 Pro, I suppose it will also work for the Ender 3, although I have not tested it. This guide is attached to the X axis motor so that it does not rub against anything (you just have to loosen...

I have rounded the outer Stopper. ...It's only for the Optic. With this filament holder, the spool cannot slip down.

I have rounded the outer Stopper. ...It's only for the Optic. With this filament holder, the spool cannot slip down.

The Ender 3 Pro spool shaft does not rotate so I figured it was simpler to have a non-rotating spool shaft for the Ender 3 S1 Pro. Although the part is printed with support, the only area of the part that is supported is the mounting detail. The...

I created this while training in Tinkercad. ...I needed a spool adapter to put 1kg SUNLU spools on my Ender 3 Pro. ...Edit it online at https://www.tinkercad.com/things/rMwJ9eGhRvQ.

I copied the guide directly from @Holspeed's design because it works perfectly and I appreciate how easily it slides over the bracket on my Ender 3 Pro. The filament sensor is a combination of several designs found here, with special thanks to...

After searching through several versions and remixes using old Z-axis endstops as filament runout sensors, none seemed to match my Ender 3 **PRO**'s endstop perfectly. Now one does exist. I printed it out, installed the endstop, and tested with a...

This is a remix of hudja's "SKR 1.3 / 1.4 case for Creality Ender 3 and Ender 3 PRO". This case is designed for the Ender 3 Pro and the SKR 1.3 / 1.4 motherboard with wifi module, a 4020 fan, three (3) LM2596 buck converters, a bigger hole at rear...

Combined the two designs to allow both the light bar, and the spool reposition at the same time. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: Yes Resolution: 200 Infill: 90 Filament: PolyMaker PLA Black Notes: ...

You can find spool holders here, that fit with the Ender 3 S1 Pro. Drill a 8mm hole into the shelf and screw holder and lid together. You have to remove the metal plate at the back of the filament guid. Not sure how it performs for high prints,...

I remixed the version for the Ender 3 to match the dimensions of the Ender 3 Pro. Ionize's version had the guide and sensor 4mm over to the left which didn't leave a straight path for the filament. The sensor I used is a cheap one from aliexpress...

This is for the Ender 3, Ender 3 Pro, Ender 3 v2. It will allow the sensor to mount on the back in front of the extruder. I didn't find a bracket that mounted at the right height. And most of the sensor brackets required lot of support. I designed...

This is a remix of [Filament Runout Sensor w/ Creality Limit Switch](https://www.thingiverse.com/thing:4547442) The original Sensor is good, but I created this remix because I needed a sensor for my Ender-3 Pro and it is in an enclosure. The...

... no EZOut mount. ... This should work on Ender 3 and Ender 3 Pro. It isn't the prettiest but works great. There are 3 STLs. Print the mount plus 2 wheels and 4 spacers. ...I used 20mm M3 to screw together and a couple 608zz bearings I got on Amazon.

It seems like almost all Ender 3 Pro tool trays require at least 120g - 400g of material, sometimes this isn't even including support material. 2. Along the same lines, comparable prints take between 12h - 24h to print, which I thought was way to...

With this new cooling setup my Ender 3 Pro can now print PLA+ at 120 mm/s and PETG at 80 mm/s with the same quality I had before at 60 and 40 respectively. Obviously the speed also depends on other things like Klipper and linear rails, but all...

This is a Filament Spool Bracket with Bearings for the Ender 3 S1 Pro. I used skateboard bearings that I had on hand. Special attention must be made when slicing the shaft (Cura) because Support must be Blocked for all except the top end of the...

Also, I didn't want to remove both screws to put it in place, as I leave them a little loose to prevent binding on the z screw that the Ender 3 pro is prone to. With the one screw design, I could tighten the screw on the left that holds the guide on,...

To achieve this, I used a Push Fitting Connector from my Ender 3 Pro and attached a short piece of Bowden tubing to it, then screwed it into the guide. I employed an old nozzle and a ratchet to clear the threads, ensuring the connector would screw in...

A remix of Jack1961's Filament Guide and Runout Sensor Bracket: https://www.thingiverse.com/thing:3450311 This bracket fits an Ender 3 (standard, Pro or V2) and attaches using the existing screws on the Extruder assembly that connect it to the Z-Axis...

... This is a customized remix, featuring a 5mm offset on the top component for seamless use with an aluminum extruder on the Ender 3 Pro. I'd like to extend my gratitude to Dezhe for their contribution. ...Have fun experimenting!

This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/5CiFX1Yf8qr This is a remix which has a 5mm shifted top-part for using with an alu extruder on Ender 3 Pro. Thanks to Dezhe! ... Have phun!