creality ender 3 pro filament 3d models

A collection of remixed filament guides specifically tailored for the Ender 3 Pro printer. All parts are fully printed, eliminating the need for bearings or other components. Support is only required for the two-pin sections, where 'touching build...

I was looking for a filament runout sensor mount for my Ender 3 Pro. I don't in any way care for the ones that hang on the filament. That just seems like problems waiting to happen. DorkyTim has a nice design that routes the filament just pass the z...

I was looking for a filament runout sensor mount for my Ender 3 Pro. I don't in any way care for the ones that hang on the filament. That just seems like problems waiting to happen. DorkyTim has a nice design that routes the filament just pass the z...

###Ender 3 Pro Filament Out Sensor### **This sensor circuit is based on the 555 Timer IC and will create an oscillating beep (i.e. ...continuous beep beep) when your filament runs out.** **PARTS LIST** (1) 555 Timer IC...

###Ender 3 Pro Filament Out Sensor### **This sensor circuit is based on the 555 Timer IC and will create an oscillating beep (i.e. ...continuous beep beep) when your filament runs out.** **PARTS LIST** (1) 555 Timer IC...

... than opening the controller board case and plugging it in there. Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 20 Infill: 10% Cubic Filament: CCTree PLA Fluorescent Red Category: 3D Printer Accessories

This is a remix of Filboyt's v-channel end clip designed to mount a filament guide on an Ender 3 Pro. I really love this filament guide design - it's clean, stylish, simple, and perfectly placed to keep the filament feeding nicely. However, over...

Sunhokey filament sensor holder for Creality Ender 3 V2. ...This revision extends the mounting length so it will hold stronger.

Sunhokey filament sensor holder for Creality Ender 3 V2. ...This revision extends the mounting length so it will hold stronger.

Since I recently installed a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a small housing for it. This one is a modification of my 1st version...

My direct drive ender 3's just allows the filament to glide back and forth on the top rail. ... Seeing the original remix work fine of my CR10's I did a quick remix to use the same setup on my enders without the filament sensors.

This is Filament Guide for the Ender 3 S1 Pro (maybe also non Pro) with Filament storage behind the Printer. I had the issue that with PTFE tubing to the printer or non guided feeding, the resistant was too much and there has been areas with...

This is a remix of eoyilmaz's Creality Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosurehttps://www.thingiverse.com/thing:4586351This has been modified to fit the Raspberry 3a+

For the same print parameters (50% infill) I get more than 25% weight reduction compared to the original design.Again, all thanks go out to CHE3SE for inspiring my first remix in the 3Dprinting community.Print SettingsPrinter...

I liked [Creality Ender 3 Pro - Raspberry Pi 2/3/4 + LCD Enclosure](https://www.thingiverse.com/thing:4586351) but I have an Ender 5 Pro so I took the file (v042 is what I modified) into [TinkerCad](https://www.tinkercad.com/) trimmed the front and...

I've had no issues without a bearing but if you would like to use one there's the option. Without bearing files: roller-no-bearing.STL hinge.STL mount.STL With bearing files: roller-bearing.STL 2x bearing spacer.STL hinge.STL mount.STL Print...

ALSO, REPORT ME IF YOU FOUND ANY ERROR.** Important notes -------- * Parts were tested for parts mutual matchings and collisions and thus they are accurate to some extent, although I didn't print any parts (except...

I have added a base so that it can be mounted on the right rail of the Ender 3 Pro. I have raised the lower magnet so that it is stronger and changed the size of the magnets to 10x10x2mm. I have attached a box which functions as a collection...

I created the Lamborghini themed pack for Creality Ender 3 Pro, it required a lot of work... ...the blower system is well oriented to have a better cooling efficiency.

... original spacer must be replaced with this one. I use it with the “E3D Minimalist for V6 & Volcano on Creality CR10/S Ender 3/Pro and clones” made by MediaMan (https://www.thingiverse.com/thing:3393889, THANK YOU MediaMan!!). ... Happy printing!

CREALITY ENDER-3 S1 PRO - EXTRUDER FAN COVER Creality Ender-3 S1 Pro Upgrade and Modification, enjoy our Version. If you have any Questions, just write a CommentDISCLAIMER This Product may only be printed for Personal use and may not be Sold...

Remixed to slide into Ender 3 Pro rail top rail. Need to play with the arrangements a bit, using Cura to generate auto-supports meant the print worked but left a very rough surface in a couple of locations that needed sanding down. ... Not perfect...

An alternative spool holder for Ender 3 S1 or S1 Pro. It's height is smaller than the stock part. It's stronger than the remixed source. ... Optional to strengthen the piece, but not necessary: - 1 M3x12 screw; - 1 M3 nut ;

... ... Reasons for redesign: 1. Tighter fit in Ender 3 Pro top rail. (Original design was very loose on my printer.) 2. Sleeker curves on the arm. ... Last picture shows original part (link above) on top, and this redesign on the bottom.

This small piece fits around the small brass ring that surrounds the Z-axis screw on an Ender 3 Pro. The fit is perfect and looks right at home on my machine. I used stock Cura settings with a 2.0mm layer height and the part took 15 minutes to print....

(Description in german below // Deutschsprachige Beschreibung folgt unten)Since I recently mounted a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a...

(Description in german below // Deutschsprachige Beschreibung folgt unten)Since I recently mounted a BLTouch on my Ender 3 Pro, I no longer need the mechanical Z-axis end switch. I have now converted it into a filament runout sensor and designed a...

I have printed several filament guides for my ender 3 but the end up broken over time so i decided to design an heavy duty filament guide that wont break. It's worth the effort. ... Very sturdy, no flexing or breaking.

Hi guys, When I bought an Ender 3 Pro, I sought out some high-tech modifications to boost the experience of using my printer. One of them was the filament guide that I've been using so far. It was printed without any adjustments and worked...

Since I recently mounted a BLTouch on my Ender 3 Pro, the mechanical Z-axis end switch is no longer needed by me. It has now been converted into a filament runout sensor and a small housing has been designed for it. The case does not have any...