creality ender 3 neo upgrades 3d models

Tool holder for Ender 3 stock tool - no extra screw required. Small tool in front, large one behind. Cutting pliers and other tools are securely held due to a height of 20mm. This measurement matches the horizontal profile exactly. ... The tool holder...

...... I conceived a fundamental Power Supply Cover for the Ender 3, which also muffles the PS-FAN and redirects hot air upwards. ... Note: The inner wall is excessively high and thin, causing it to wobble during printing, so I simply chopped it off after.

I made some modifications to be able to adapt it to the ender 3 pro and v2 or other bed with the same chassis. ... I strongly advise to print the model with a resin printer,the model requires a lot of details in the teeth.

This is a simple solution to the black hole over the micro sd card slot in the ender 3. If the card has been swallowed multiple times by the machine. ... It's enough to print it and insert it into the location above the SD card.

This is a variation of my Filament-Cutter design specially for the Ender-3-Pro in conjunction with an MicroSwiss hotend.The Filament-Cutter is being used in my SMuFF project in order to get rid of the ramming while swapping filaments.

This is a variation of my Filament-Cutter design specially for the Ender-3-Pro in conjunction with an MicroSwiss hotend.The Filament-Cutter is being used in my SMuFF project in order to get rid of the ramming while swapping filaments.

On Creality printers (at least the Ender 3), the cooling fan in the electronics is coupled with the part-cooling fan, so make sure to turn that on (M106 S255) to avoid overheating your printer electronics while plotting. You may or may not include...

My Neo had a different bar layout to what this file required, so I modified the file slightly to fit. All other attributes are the same as the original file. ... You will still require a long ribbon cable.

... screws on top of the main electronics cover. Once all obstacles were cleared, I could slip the final foot into its designated slot within the aluminum frame. The entire printing process took less than two hours to complete on my Ender 3 printer.

to jest rmix z opcją czyścika filamenty żeby nie blokował łożyska link do czyścika https://www.thingiverse.com/thing:3033662 Ustawienia drukowania Marka drukarki : Kreatywność Drukarka : Ender-3 v2 tratwy : NIE Obsługuje : Nie ma znaczenia...

I created this specifically to hold the UniTak3D Ender 3 3D Printer LED Lights found on Amazon here https://www.amazon.ca/dp/B0B7B1QG5Q?psc=1&ref=ppx_yo2ov_dt_b_product_details. I didn't like the way they just laid in the gantry rails so I made a...

______________________________________________________________________ This is a remix of the handle included in this Thingiverse item: Ender 3 bed handle with removable Raspberry Pi camera mount by PatriceLoco -...

... for the heater cable). I also reinforced some areas a little and enlarged the mount holes at the front to better accommodate the coarse fan mounting screws. Fully compatible with the CR Touch that comes with the stock Neo (and Neo v2). ...

While making my first prints on the Ender-3 V2 the cable that runs to the nozzle got stuck between the printbed and the motor that is situated in the rear of the printer. To prevent this from happening I designed this cable holder. The cable...

There's also a small slit on the bottom of the case, I put that there to hopefully fit an SPI cable for the TFT35 SPI, I will use this case for that, https://www.thingiverse.com/thing:6478665USB Cable - This is what I will use to connect the PI to...

This bracket mounts the factory spool holder from the Max Neo to the top rail. You can use the same screw that comes with the original holder. This is a quick prototype that still needs a little work, but I could not find anything similar. ... I...

I wanted a nice honeycomb / hexagon shaped control knob for the lcd on of Neo. Couldn't find anything to match @fedorSosnin 's Honeycomb Z axis knob. Sized nicely so it doesn't block the lower part of the screen. ...Slightly tight fit on the hole, but...

The positioning of the filament spool holder on the Ender 3 causes the filament to come down at an angle such that it rubs on the entrance to the extruder. This is a filament guide to help the filament enter the extruder at a better angle without...

There's a version labeled "Creality" and one that isn't. ...It might work for other Creality Printers as well. The design doesn't look great with Smurf-Blue PLA, but my black PLA was all out. ...I'd love to see your prints in another color, though!

This is a compact cooling vent for the standard fan that comes with the Ender 3 printer. To install it, simply swap out the original fan duct with this one. For optimal results, print it from PETG due to its proximity to the hot end, but...

**Other Ender 3 Parts.** [Tusk Fan Shroud](https://www.thingiverse.com/thing:3055926) [Z Endstop Bracket](https://www.thingiverse.com/thing:3057136) [Y Endstop Bracket](https://www.thingiverse.com/thing:3057132) [Cable...

I found the original Ender 3 spool holder too short and too thin for most of my filament spools. All filaments I use have a 50mm diameter hole and a width of just over 100mm. So those spools run with more friction and are worse secured because they...

Additional parts needed 2@ M4 X 16 screws 2 @ M4 T Slot Nut Fastener This is a top gantry LED mount for an END 3 Max Neo. It pairs with my X Axis gantry LED mount. https://www.thingiverse.com/thing:5931926. This design is good to give overall...

https://www.thingiverse.com/thing:3639454** I stumbled upon Filboyt's Ender 3 vent ring creation and was impressed, so I decided to print it out. It fit perfectly with my printer, and the 'bowl of water test' confirmed its excellent performance. So...

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

I just wanted to have my 250ml IPA bottle always near my Ender so i created that holder.

Unfortunately this doesn't work for the Ender 3 v2. This has been designed for printers that have been converted to direct drive or do not have their extruder in the same place. The only extra hardware you will need is one M6x20 bolt with a nut, it...

You must print the piece labelled ‘cable chain - link’ 15 timesI will release a video of how to install it in a week or two whenever i can.Unfortunately this doesn't work for the Ender 3 v2. This has been designed for printers that have been...

I am designing a new case for my Ender's power supply, electronics and screens, so I am recreating each part in Fusion 360. Thought I would share for your designs. ... If you can print this into a working model I will be highly impressed.

... M4x15. It employs an original Creality nut, which serves as a crucial component. Initially, I utilized a roller with extended functionality to catch the 10mm diameter end within a bench drill, after which I smoothed the surface using sandpaper.