creality ender 3 filament 3d models

I modified my son's filament sensor mount to be able to mount the Creality filiment sensor on my Ender 3 V2. https://www.thingiverse.com/thing:4890156 His mount corrects alignment issues of other mounts for the Ender 3. ...His uses the repurposed Z...

Remix from https://www.thingiverse.com/thing:4781650 with added hole to put filament easier. Also decided to remove ball to make it simpler. ...The guide perfectly fits into creality's enclosure.

The original bolts are M3 x 16mm CSK I have run the printer with about 100M of PLA+ and there are no issues that i can see caused by lifting the filament sensor by 3.2mm. No visible abrasions etc. My filament is also side mounted if relevant. ...

FlexiStruder for Creality Ender-3 and CR-10 Necessary for printing from the flexible filaments. ... Flexible filament settings by Maker's Muse: https://youtu.be/fTJz6vMvtJ8 BOM: 1x MK8 drive gear 1x PC4-M6 fitting from stock extruder 1x 608zz bearing 1x...

FlexiStruder for Creality Ender-3 and CR-10 Necessary for printing from the flexible filaments. ... Flexible filament settings by Maker's Muse:https://youtu.be/fTJz6vMvtJ8 BOM: 1x MK8 drive gear 1x PC4-M6 fitting from stock extruder 1x 608zz bearing 1x...

... TIGHT FIT to printer frame UPDATED (5.07.2021) - After 3 print tests I achieve really good tight fit. ...If your printer prints with "elephant foot" you will need to remove it Simple filament guide - Easy snap in - No supports - 1.75mm filament

Ender 3 Filament guide modified to fit onto gantry that has the Creality Ender 3 Neo LED light kit installed. The screw that comes with the light kit is used to attach and secure the filament guide base to the gantry against the light kit. ... A...

Système 4 en 1 : - détecteur de fin filament, - protection contre les nœuds, - guide filament, - protection pour éviter que le filament touche la vis trapézoïdale. Matériels : 2 Vis M3 10mm, 2 Vis M3 20mm, 4 écrous M3, 1 roulement à billes 608ZZ...

It does not come with a mount for the filament sensor, this slides onto the existing nut if you are side loading filament. By the way. ...This goes at a slight angle, allowing for the filament to just go in smoother.

This is a replacement feeder arm nothing special

The concave roller centers the filament before it enters the filament feeder, allowing the filament to flow smoothly. This improvement has greatly enhanced the quality of my 3D prints! I threw away the "eyelet" type guide and replaced it with this...

None of the designs I tried worked well with the Creality direct drive, so I made my own. Version 2.0 is a little shorter, and has cable clearance for the stepper motor cable. ... My design: https://www.tinkercad.com/things/dseulqFPcqt

I made this attachment to make it easier to print legs for the base of my cr-10 so I can one day put the control box underneath the printer. You will need five M3 screws(12 mm) and five m3 T-slot nuts to slide into the printer rail's. I printed the...

I made a few adjustments to the design posted by KInd_Error that made it work with a standard 608 bearing and M5 screw.

Crealıty Ender 3 v2 filament holder

... Edit: Experienced problems with high-retraction models where the extruder gear was chewing a flat spot into the filament, so uploaded an updated extruder bracket with a 3mm offset for the spring instead of 4mm to reduce pressure on the filament.

Modified version to give a little more room between the extruder and the sensor.

Remixed -- Creality (Ender 3) Creality (Ender 3) Filament holder 80mm spools by mjoaris Nov 11, 2018 This is a dual roller bearing spool holder that secures onto the original Ender-3 spool mount. ...It's necessary for a dual extruder application or...

... and properties that can enhance your printing experience. By following these simple steps and tips, you'll be well on your way to mastering the Creality Ender 3 filament guide and unlocking a world of creative possibilities with your printer.

... dimension was increased accordingly. Creality CR10/Ender 3 Filament Guide Dimensions: For those relocating their filament spool above or below their printer, these measurements are provided in inches. ...Scaling for metric units will be necessary.

A standard printer holder is used, or as in my case "Creality (Ender 3) Filament holder 80mm spools" by Mjoaris. Filament spool holder rotated 45 degrees to reduce the height of the printer. A standard printer holder is used, or as in my case...

(https://www.thingiverse.com/thing:3209211) The spool is a file that actually came directly from a remix of mjoaris' design: "Creality (Ender 3) Filament holder 80mm spools PLUS 30deg remix," by Sporktek. ...(https://www.thingiverse.com/thing:3819690) ...

Here's another Creality Ender 3 Filament Guide, this one a minimal screwless snapfit version that keeps the shiny open 608 ball bearing in focus. This guide is still a work in progress, but it works fine if printed well. ...To remove the guide, simply...

The filament used was Overture 1.75 PLA ------------------------------------------------------------------------- Print Settings Printer brand: Creality Printer: Ender 3 Rafts: No Supports: Yes, on bed only Infill: 20% Filament brand: Overture...

The Creality Ender 3 Roller filament guide has been my go-to choice so far, but since I've mostly printed with PLA, the part that pushed into the extruded aluminum kept getting loose over time and would fall out occasionally. This updated version...

Combined X-axis support and lower filament guide for the Creality Ender 3. ...Print with supports disabled. Remixed from: Creality Ender 3 - X Axis bearing support by Creality, 2019 / Ender 3 Filament Guide by Makerbot

So here's another Spool Holder for your printer, but the big difference with others is that this one fits perfectly on the Creality Ender 3 filament/spool arm. All you need to do is print the part and get some screws and nuts to attach it securely. I...

Creality Ender 3 Spool Filament Guide Mounts Horizontally on Top Rail The filament spool guide mounts neatly to the top metal rail, adjacent to the spool. By doing so, it eliminates tangled filaments caused by the print extruder head's upward Z-axis...