creality ender 3 fan 3d models

You can use this design to improve hotend heating. ... No additional fan is required. ...

:-) This mod is verified to be compatible with: - Ender 3 S1 - Ender 3 S1 Pro - Ender 3 S1 Plus As of version 4.0, this duct is compatible with: - Spider Hot End Mod (3.5mm lower, use the provided STL, not the stock one) This mod is NOT (yet)...

Lightweight Build for Single 50x50x15 or 50x50x20 Fan More Than Enough Cooling is Provided A Previous 80x80x15 Version was Used, but it Provided Stupidly High Amounts of Airflow :D The Downgrade to a 50x50x15 Fan Has Been Made Images are Available at...

This replaces the original ShroudFor 40x20mm Hot-End Fan and the stock 4010 Blower Fan!I made a new version of my "Clean Shroud" that holds a 40x20mm Hot-End Fan and the stock 4010 Blower Fan (with its mounting) for Creality Ender-3 V2.You can still...

I made a new version of my "Clean Shroud" that holds a 40x25mm Hot-End Fan and the stock 4010 Blower Fan (with its mounting) for Creality Ender-3 V2. You can still use the original screws, but you will have to heat one screw up with a lighter and...

This is a remix of: https://www.thingiverse.com/thing:4528533 The new Creality Spider 3.0 is a little different from Creality's usual hot ends in that the wire bundle is located on the LH side of the part as opposed to the RH side. I had to shift...

I utilized two 5015 fans to make my Ender 3 a bit more tolerable. update: Actually, don't print this! The 5015s are apparently not designed for that setup. ...They got excessively loud right away.

Replaces the old frame for 40mm fans, to increase the air volume and lower the fan rpm. Combined with Noctua silent fans its probably the best solution. ...The distance between nozzle and the original radial fan increases a bit.

I DESIGNED THIS TO USE ALL STOCK FANS WITH AN OPTION TO ADD ANOTHER 40MM DUCT TO THE LEFT SIDE FOR DUAL PART COOLING AND USE A STOCK COOLING PART FAN DUCT STYLE CONFIGURATION SO IT WILL BE LIGHT WEIGHT. PART FAN IS ANGLED A LITTLE BIT SO I COULD FIT...

This is a basic ABL mount designed to be compatible with gibbed's eB Fan Shroud in either the 4010 or 5015 variant, or any cooling solution that leaves the x-carriage backplate completely empty. There are two main variations on this design with...

This is a new design for all Creality Ender 3 printers (excluding only Ender 3 S1), CR-10 and Ender 5 Plus with Micro Swiss Direct Drive Extruder along with the original BLTouch metal mount. Inspired from Satsana 5015 Fan Duct and Orbiter Fan duct,...

This is a remix of the Satsana 5015 Fan Duct from eric_anastas modified to fit "ALL" Creality Ender 3 printers (excluding only Ender 3 S1) and CR-10 with the Micro Swiss Direct Drive Extruder using the "original" BLTouch metal mount. It's been...

:) https://paypal.me/cdsmakestuff Dual Cooling Fan Upgrade with BLtouch Mount Fits Creality Ender 3 (OG) and Ender 3 Pro Ender 3 V2 Version coming Soon. Why another? Well I tried a lot of different existing designs and just wasn't happy with any...

:)https://paypal.me/cdsmakestuffDual Cooling Fan Upgrade with BLtouch MountFits Creality Ender 3 (OG) and Ender 3 ProEnder 3 V2 Version hereWhy another? Well I tried a lot of different existing designs and just wasn't happy with any of them. I wanted...

A Compact LED Display with Three 5mm Slots. ... https://www.thingiverse.com/thing:2767047

Is a remix of https://www.thingiverse.com/thing:4408571.Fan duct for Creality CR-10 / Ender 3 printers with Micro Swiss Direct Drive Extruder. Suitable for 40x40x20 fans and BL-Touch.BL-Touch offset X=-46 Y=-9The holes for the fans were fitted with...

:)https://paypal.me/cdsmakestuff Dual Cooling Fan Upgrade with BLtouch Mount Fits Creality Ender 3 V2 Ender 3 (OG) and Ender 3 Pro version Here: https://www.thingiverse.com/thing:5403671 Why another? Well I tried a lot of different existing designs...

:) https://paypal.me/cdsmakestuff Dual Cooling Fan Upgrade with BLtouch Mount Fits Creality Ender 3 V2 Ender 3 (OG) and Ender 3 Pro version Here: https://www.thingiverse.com/thing:5403671 Why another? Well I tried a lot of different existing designs...

... nozzle height right. 13/9/19: Volcano BLTouch mount added. 10/5/2020: Mount modified to fit the Ender 5 in addition to other Creality models (Ender3 and CR machines). ...If needed just let me know and I'll add a version with provision for inserts.

... between the duct and silicone sock on the heater block. September 13, 2019: A Volcano BLTouch mount has been added. May 10, 2020: The mount has been modified to fit the Ender 5 in addition to other Creality models (Ender3 and CR machines).

There is also the possibility to install a fan. The connectors of the Raspberry are also added, so nothing has to be cut or drilled. The LCD display cable can be easily routed through the opening at the bottom. ...A quick installation is possible by...

MBOT3D MK2_Rev2.0 (Ender7 style fan duct) by Ahmad Sunardi:https://shorturl.at/lpILV TheBuildBay version:https://shorturl.at/pqITY Whole story was about I want to upgtade my ancient Ender 3 "pro" with high flow hotend. So I found TheBuildBay's...

I could not find the perfect shell for my taste and need (fitting it upside down to the lower side rail of a Creality Ender 3 Pro to run octoprint), so I took the most good looking I found IMHO, and tweaked as needed. Here are my edits: - added...

Compact Trifan Ender 3 Pro Hotend Housing remixed to fit Creality Spider Hotend (high version) Dual blower fan Creality Spider hotend High-temperature is a long model therfor needs a longer fan duct. ...I combined the housing with fan duct in one piece....

This way the fan only spins when the power supply needs it to.Printer: Creality Ender 3 MAXFilament: OVERTURE PLAInfill: 100%Support: NOAdhesion: As you wishNozzle: 0.4mmQuality: CURA adaptive layersITA:Ho creato questa cover per una mod che ho fatto...

I made this Because I own a printer that doesn't Exist - Or better, there is a severe lack of information about it Online (It's called EZT3D M09?) For my printer, which is oddly similar to the Ender 3, there is no compatible fan configuration as the...

Hero Me Gen 5 40mm Noctura fan cover with cable management. ... I have designed this to cover the cable route while running dual 5015 fans and protect the 4020 Noctura from accidental damage.

This is a fully parametric OpenSCAD file to generate the parts necessary to replace the (frankly useless) stock heatbreak and cooling fan assembly on Ender 3 and CR 10 printers with an E3D-V6, AKA "volcano" all metal hotend. My Tronxy P802 and my...

###Chimera Dual Extruder mount/cooling system 50mm fan version for Tevo Tornado/Creality CR-10/Ender-3 It's a base module that combines a mount and cooling system specifically designed for the e3d chimera dual extruder, compatible with Tevo Tornado,...

It is a remix of the hero me gen 7 single 5015 fan duct to make it fit for a Creality Ender S1 & S1 Pro. Most other Ender 3 S1 & Pro ducts are routing them to the right side of the CR touch module; however that results in a narrow air channel...