creality ender 3 3d drucker

This updated version is now compatible with my newly designed direct drive extruder model, also available for purchase separately from Creality's dual gear extruder. Corrections ----------------- * Increased fan cover wall thickness to make it more...

I designed this simple guide so my filament filter doesn't mess with threaded rod. ...I designed 3 versions with different gap position and 1 without any gap.

This is a basic octopi station that goes under your display module and can store your raspberry pi (either model 3 or 4)

Here's a video that shows how it works and where it should be installed - it's not perfect, but it's better than nothing: https://www.youtube.com/watch?v=gYs1RouDY1k I've included two versions of part "A" - one is specifically designed for Ender...

I wanted my spool holder to be able to hold 3 500g spools for easy color switching. ...This extension just slides in the original spool holder with a tight fit and extends it by 35mm.

LED strip bar for Ender3. ... In 3 parts to be able to be printed on my printer. ... I printed it in PLA, but it will be stronger in ABS.

This 3D printed phone case fits perfectly on a Samsung Galaxy S6 without any issues and doesn't require any additional supports to print successfully.

Simple 3d printer feet for damping vibrations Support required only on the top part. ... Keep infill low so it stay flexible

This is my first 3d Home made file By Combining Theses https://www.thingiverse.com/thing:3317795 https://www.thingiverse.com/thing:3597420

A clever clip that prevents printer filament spools from slipping off is a must-have accessory for every 3D printing enthusiast and professional alike.

... because I had Problems with the pen wobbling on the paper. ...This version does'nt include the spring, so be careful when leveling, and maybe first home the 3D printer before leveling the pen.Instruction on how to use 3D-Printer as Plotter:  Link

... bolts, just enough to hold it tight. I have added some holes and a channel to keep the web cam wire tight and neat, and the hole in the bottom is to place the web cam wire through.The top hole is big enough for a 3/8 bolt which fits most web cams.

<p>Remix of the MakeChetti's tensioner case, I found out that the belt is a bit too high and rubs on the extrusion instead of running inside. ...This version keeps top side roughly in level with the stepper pulley. Category: 3D Printer Parts

I uploaded these files specifically for those gorgeous overnight prints, and also because the lighting can really throw off the balance in my 3D printing videos. ...Check out my channel at...

... infilI only used a grip on the base, flap or raft for the pin print, because of the height and to not have to reduce the print speed. ...if your printer 3D is well calibrated, just reduce the speed to go well :)  Thanks for Download this Model ;)

they keep the filament nice and straight.) I recommend 3 clips however 2 work. 5. Make the filament at 150mm and 100mm 6. Remove the mount and clips and extrude 100mm of filament, DO NOT TRY AND EXTRUDE WITH THE MOUNT IN PLACE. 7. See how much...

This build is perfect for newcomers to 3D printing, featuring a simple design that's easy to create. I recommend printing this handle on the vertical side for a smooth surface finish. I've also added a grabber to enhance stability and prevent...

I'm not a fan of LED strips, so I designed a custom LED module holder for my 3D printer - one like this model is available from gme.cz, specifically the dsh.517-730.1.pdf document.\r\n\r\nTo build it, I used M3 screws to secure the V-Slot aluminum...

also filled some grooves inside the duct cause they were causing thin wall conditions Used the MS 3d builder so it doesnt look clean but it does the job I printed it at 45deg, with no inside supports to minimize bridging, looks like it would also...

... fine. A second issue was that my printer would NOT print the center leg at the bottom of part 2. I tried 3 times and it would always just snap off at the same point (during printing no less) so I removed the curves and added a straight post.

... (only tested with 1kg spools) i recommend high infill 20% or more. No supports needed, 0.2mm layer height is fine. Once printed, I pushed it into the factory spool holder then used the factory nuts to attach to the printer. Category: 3D Printing

... I attempted to craft a 3D image file without the ring, but my skills in this area are limited, resulting in an inferior product compared to printing the large design and simply cutting off the excess material to achieve the desired effect.

... getting really hot in there. ### Top Version 2.0 Top of the case has a hole for a cooling fan. Now it's much better. ### Top Version 3.0 Added a fan cover, so the parts get cool air for cooling instead of the hot air under the heatbet. ...

they keep the filament nice and straight.) I recommend 3 clips however 2 work. Make the filament at 150mm and 100mm Remove the mount and clips and extrude 100mm of filament, DO NOT TRY AND EXTRUDE WITH THE MOUNT IN PLACE. See how much filament was...

After buying my first 3D printer I tried to personalize it by printing various objects including a tool holder. I printed what seemed best for my use, but at the end I decided to make one the way I liked it and this is the result. I have used an...

Extruder Knob for the Creality Ender 3, Ender 3 Pro, CR-10. Fits perfectly on a 5mm shaft with flat part. ... Please, share a picture of your makes!

Ein Winkel Zur Stabilisierung des Alu-Rahmenprofils eines 3d Druckers

I have the following Rail kit from Creality, but it looks like they changed the rails: https://www.banggood.com/Creality-3D-Linear-Rails-All-Kit-for-Ender-3S-or-Ender-3-Pro-3D-Printer-Part-with-Leveling-Sensor-p-1728277.html?cur_warehouse=CN I was...

ENDER 3 PRO LCD CASE LOGO ENDER CREALITY CRUCIAL NOTE: SCALE UP TO 10% FOR A TIGHT FIT. ... PLEASE REACH OUT TO ME AT DIEGO_OCHOA_GUERRERO@HOTMAIL.COM, I'D BE HAPPY TO SEND YOU A .3MF FILE TO PRINT ON YOUR ENDER 3 PRO.

**Bill of Materials** - M3 Threaded Inserts (6x) - https://geni.us/ThreadedInserts - M3 Round Head Screws & Hex Nuts (various lengths) - https://geni.us/M3-Screws - 3x7x3 mm Ball Bearings - https://geni.us/7pVaEB **Print Settings** - Filament: PLA -...