creality dual extruder upgrade 3d models

Adapter to use the Creality Metal Extruder on the Creality Direct Drive Extruder-Upgrade. ... To use this adapter, the M4 screw to hold the spring must be replaced by a M3 threaded rod.

This remixed Flashforge Creator Dual Extruder model addresses issues with the original's 2mm-thick arms, which prevented proper heat sink placement and arm movement. The revised design features thinner arms and reduced spring space for optimal...

I had upgraded the stock extruder on my Ender 3 to the grey metal one from Creality, which has a rectangular housing around the compression fitting threading instead of triangular as the stock extruder has, so I modified the opening to accommodate.

Fine Tunning this excellent extruder upgrade from user @Jsphtg for Creality CR-10S Pro V2. I tweaked a little bit more the feed filament hole to fit at diameter 2,1mm which i found perfect match while using TPU/FLEX filament. Moreover you dont need...

You will need 6 - m5 x 40 bolts and nuts The parts I found were for creality, my printer is home made. If your printer uses a 4020 V type extrusion on the left and a 2020 V type extrusion on the right you can possibly use this. I used no support....

Modified feeder designed to enable flexible filament printing on Creality Bowden machines. This is a modification of the original file found here: https://www.thingiverse.com/thing:2144277. ...The goal was to eliminate the need for the PTFE tube...

Extruder plates equipped with a plastic PTFE fitting hole will inevitably seize and collapse over time. This revised design employs an M6 nut to secure the fitting firmly, providing a more durable solution. I also aimed to utilize flexible filaments...

I replicated it, but my flexible filament still got stuck in the extruder's sides. ...I didn't like the concept of the extra "tube" style because my filament continued to escape, so I started from scratch on NX7.5 and created a precise fit around the...

I was having trouble printing with some flexible filament right off the bat using my Creality CR-10S Pro, so I experimented with a few mods from here but none of them delivered the results I needed. To get something working, I combined elements from...

I upgraded my extruders on the CTC and created a custom cover to fit them. The Makerbot Replicator 2X Full Metal Extruders I bought from ebay required an angle cut for their sprung hinges, as the original cover wouldn't let them close tightly enough....

This is a clip designed to fit snugly atop the tension arm of a Winsinn/Creality Dual Gear Metal Extruder, allowing you to seamlessly connect a bowden tube to the extruder's intake for effortless filament guidance into the extruder. ... I encountered an...

This design allows consistent filament feeding by providing enough space for both extruders to utilize the "Minimalistic MK8 Upgrade" alongside my "Spring Enhancer / Spring Compressor". The standard plate shipped with the Replicator Dual is a bit too...

It turns out that between the MK8 extruder design and Creality's dual geared extruder, they share the same filament path (same distance from left to right and dimensionally the same from the bottom up), despite the fact that the dual geared design is...

Filament Guide for a CR-6 SE with dual Gear Extruder.It is a Remix from this: https://www.thingiverse.com/thing:4586801Print SettingsPrinter Brand: CrealityPrinter:  CR-6 SERafts: NoSupports: NoResolution: 0.20mmInfill: 10%Filament: Creality PLA...

**Malyan M180 - Upgrade to Dual Bowden Extruder for Enhanced Performance** I decided to replace the heavy dual extruder head with a much lighter bowden extruder, allowing the M180 to print faster and quieter. Due to the limited slicers that work...

It ensures precise alignment of the filament, thanks to its dual drive extruder design, which is slightly taller than the standard plastic version. Unlike other brackets that rely on z-axis spindle screws, this one attaches securely behind the third...

This is for the ender 3 max if the dual gear extruder all-metal lever is installed. the filament sensor is too low and the hole for the filament does not line up. This block goes under the filament sensor and raises it to the correct height. ...You will...

https://youtu.be/PrdRSvT4WRI Parts need to buy: BMG Extruder clones: http://ebay.us/MZf0a6 E3D V6 Hotend / Heatsink: http://ebay.us/hkRyrC Reuse old Fans and Linear Bearings, check how to remove Linear Bearing from Aluminium Block...

Filament Guide for a CR-6 SE with dual Gear Extruder. ... It is a Remix from this: https://www.thingiverse.com/thing:4586801

... the same principle. I utilized the existing extruder parts but reversed their orientation, positioning them upside down. ...By employing the wiring from hotend 2 in hotend 1, no adjustments to the Firmware were necessary to reverse the rotation.

For Creality Dual Gear Extruder Just a remix that I made because i was getting slight problems with the actual model. Reduced the size a bit and made it simplier in the exterior (just for looks, not functional but might save some filament). The...

Recently, I installed Carl Raffle's cooling block upgrade on my 2X printer and modified rmcniff's extruder for enhanced performance. With this combination, I achieved successful PLA printing for the first time. To accomplish this, I made adjustments...

For Creality Dual Gear ExtruderJust a remix that I made because i was getting slight problems with the actual model. Reduced the size a bit and made it simplier in the exterior (just for looks, not functional but might save some filament). The...

This is a simple insert for the Creality (clone) dual gear extruder to make the filament path going out of the extruder a bit tighter, because while it is better than the stock, there is still a huge gap between the gears and the hole in the...

This is a simple insert for the Creality (clone) dual gear extruder to make the filament path going out of the extruder a bit tighter, because while it is better than the stock, there is still a huge gap between the gears and the hole in the...

This is a major upgrade based on the phenomenal work of both rmcniff (http://www.thingiverse.com/thing:222667) and countspatula (http://www.thingiverse.com/thing:256754).\nLike countspatula I recently installed my Carl Raffle Cooling block and hot...

Parts need to buy: BMG Extruder clones: http://ebay.us/MZf0a6 E3D V6 Hotend / Heatsink: http://ebay.us/hkRyrC Reuse old Fans and Linear Bearings, check how to remove Linear Bearing from Aluminium Block...

This extruder offers several key features: - Utilizes the Creality Ender 3 original heater - Allows for the installation of a 20x20x10 mm fan on the heater - Enables the fitting of a 20x20x10 mm fan on the part - Facilitates easy cabling -...

You can find it hereAdapter for the official Creality Direct Drive gantry released for Ender 3 + Dual Gear extruder to be used with the Hero Me Gen 5.I am not sure if Creality still sells it, but it's the one seen in this video by CHEPPrint it with...

[You can find it here](https://www.thingiverse.com/thing:4790273) --- Adapter for the official Creality Direct Drive gantry released for Ender 3 + Dual Gear extruder to be used with the Hero Me Gen 5. I am not sure if Creality still sells it, but...