creality cr6 3d models

https://www.youtube.com/watch?v=B6ID1zSqvd4 This is a combination of this https://www.thingiverse.com/thing:1258498 and this https://www.thingiverse.com/thing:4620590 - but both were highly modified. The end cap of the stepper seemed like the...

<p>I'm not much of a designer (check those damn ducts) but I think I have some good ideas and this is one of them.</p><p>This is meant to provide more air to cool the parts, being a free upgrade if you are using other fans and have the original...

I printed the original thing this is remixed from in PETG, so it looks pretty blobby etc, but it's strong stuff - however, I'm using it with a 4020 fan instead of a 4010 fan and within about an hour the weight had made it start to droop and it was...

Props to the original maker. I remixed the long version of the original drawer to have a flat front and a stronger handle - just like my right-side remix here. https://www.thingiverse.com/thing:4703142 You can see my matching right-hand drawer...

See my make for more and better photos. I didn't like the idea of having to have my motherboard fan on full power all the time - but the stock one was tiny and noisy. I discovered that Arctic Cooling make a very cheap (and quiet) 92x25mm 12V fan...

This is not really a remix, I just added a couple of bits onto the already excellent design. I modified the cover that clips onto the x-axis stepper motor by adding the camera mount from my thing here https://www.thingiverse.com/thing:4654989 (you...

This isn't really a remix, but additional plates to cover the wires after installing arkworkvideos excellent Power Supply Cover for the CR-6 SE. I didn't like have any wiring exposed - especially mains. There are two versions - just two flat...

All I did was add a chamfer to the handle of the original remix to make it stronger. I printed it with a 1-4mm chamfer, but when it came out I wish I'd used a 2-4mm chamfer to make it more pronounced/stronger. If it breaks I'll print the newer one! ...

The original author is very talented and did an amazing job with the mold - but three times I snapped off those little sticking out bits on the "Outer Part Bottom". So I made it a lot stronger and used a chamfer. It uses a bit more filament and it...

I just extended the bottom. moved some of the side vent holes around and added rail brackets. This will fit a raspberry Pi model B 1, 2 or 3. It will fit into any rails that are the same as the CR-6 - but you may need different lengths of V-slot...

This is not the slightest bit original. RICBRU did all the work. I just wanted a top without a logo hole that would allow dust etc in and I also wanted PTFE instead of printed lines for the filament to go through the exit into the extruder. I...

This cover is great, but it doesn't work if you use a 40mm hot-end cooling fan. Basically all I did was chop a chunk off the side to account for the larger fan. I also wanted to be able to mount an LED strip to the side of it instead of the awful...

I basically made the fan duct stronger in a few weak areas, made it easier to print, moved it down and changed the angle a bit (to get my 4020 fan to fit under the bed levelling sensor wires). I made the mounting bracket massively stronger and...

Feel free to add to them! i dont use all of these at once,, i recomend the M3 bolts instead of pins but doesnt matter just may last longer! Hello and thanks for shopping..100%discount here! I accept donations toward making prosthetics! Please if...

I remixed my remix to improve on the design. This one is taller (goes further down), has a base and positions and angles the LED strip better. It still includes the cut-out for a 40mm fan, but this one interferes with the bed sensor less. I used a...

AVISADOR ALARGADOR PALANCA EMBRAGUE RUEDA DENTADA FILAMENTO FEEDER HANDLE CREALITY CR6 SE (¿DALEK)

CR6-SE Hotend end adapter for Creality Spider HotEnd. Part A: HotEnd Adaptor - Primary support for the HotEnd. Important: The spider's default pneumatic coupler will not fit the CR-6 SE top mount - you will need to replace this with a PC4-M10...

As any owner of a Creality CR series printer will be happy to tell you, the filament sensor is located so closely to the extruder that if it does detect a break or the filament runs out, it's very hard to recover from it because there's no room to...

the Creality CR6-SE printer is very similar in many ways and the MicroSwiss all metal hotend for the CR6-SE can be very easily made to fit the CR-10 Smart.► https://store.micro-swiss.com/products/all-metal-hotend-kit-for-creality-cr-6-seOther than...

&nbsp;This “tweak” simply cuts-out some of the plastic, in the shape of the Creality logo that is on the stock hotend assembly, from the face against which the fan is mounted. &nbsp;I made this change on my machine because I happen to like the...

I wanted a simple way to mount my raspberry pi camera with LED ring to my new CR-6 SE at a 45 degree angle. I based my design on this https://www.thingiverse.com/thing:3870779 I decided to use screws and nuts because I didn't want to to move...

This is a laser holder console to https://www.thingiverse.com/thing:4701896 direct drive extruder.

Cover for the Creality logo top frame under handle, after all, it is a 3D printer. ... Attach w/double sided tape

Cover for the Creality logo top frame under handle, after all, it is a 3D printer. ... Attach w/double sided tape

All the cable clamps I've found just popped out far too easily. These have to be slid in, but frankly you're only going to be doing this once, so removing an end-cap (or printing and screwing one in) isn't a big deal. You can use the v-slot cover...

<p>Just a simple remix to add the ability to use a M10 fitting.&nbsp;<br><br><i><strong>Instructions:</strong></i><br><br><i>Print with supports!</i><br><br><br>For V1:<br>You should test to see if the filament goes through the end, but it probably...

Just a simple remix to add the ability to use a M10 fitting.  Instructions: Print with supports! For V1: You should test to see if the filament goes through the end, but it probably won't! So you need to use some small hex keys or...

Creality CR6 SE Update Extruder

A tool organizer for the Creality CR6-SE

This is a direct drive for creality cr6-se.