creality cr6 3d models

Just a remix to mount the ADXL sensor on the PEI sheet because I have a handle and it is difficult to use any other sensor mount. This is easy and quick to install. You are going to need two heat inserts (M3x5x6) for the center holes and M3 screws...

A larger knob to go over the tiny X & Y adjustment knobs to allow a finer touch when adjusting.

Most important parameter: I had to set 2mm retraction to avoid clogs.

A simple support to lessen the strain on the printer spool holder with 1KG rolls

Tooless mount for GoPro

Just a remix to mount the ADXL sensor on the PEI sheet because I have a handle and it is difficult to use any other accelerometer mount. This is easy and quick to install. You are going to need two heat inserts (M3x5x6) for the center holes and M3...

This contains two items;A remix of my own “Creality CR6 - Sherpa Mini Mount” (https://www.printables.com/prints/258342-creality-cr6-sherpa-mini-mount) to be able to fit the “CR6 5015 part fan shroud dual fang” from K2van...

These feet will dampen the vibrations, raise the height and allow you to pull the printer forward (if you need to, mine is on a cupboard that wasn't quite deep enough). Print them in TPU and thye work just great! ... I used 40% infill density.

A screw-on holder for the CR-6 SE Display SD card 2 micro sd adapter

Hi. Here is a quick mount to re position the filament run out sensor, to point towards the back, this bracket mounts to original position, then mount the FROS to that. Will need 2 extra m3 x 20 and 2 m3 x 10 countersunk bolts. I use this in...

This is designed to be clipped on to the modified filament sensor case here https://www.thingiverse.com/thing:4635094 and it will direct the cable over the extruder instead of down the side of it. I have not printed/tested this, but it should work...

This is a remix of the remix! I just made it completely flat on the bottom in solidworks and I also made the outside and top of the ring flat too. It should be much stronger now. This is a good base for modification as the original mesh was VERY hard...

See my make for more photos. This thing was inspired by this thing https://www.thingiverse.com/thing:4688169 but I made it all from scratch and it's quite different. It's only 38mm by 28mm as that's the only space I had behind this drawer for...

The X&Y tension adjusters have no resitance and work loose after time, this mod adds a clicking action to lock them into position

I've tried adding LEDs to a few different fan ducts that go around the hot end and blow air down instead of the stock system and they've all worked really poorly - but I still didn't want the stock blue LED. I came up with this small adapter that...

My first remix ! ;) https://www.thingiverse.com/thing:4654645 The mounting design on the original fits perfectly on the head But I didn't like the orientation of the clip, and I kept breaking it trying to fit the ribbon inside. ... I found...

Onepiece print for the hotend, to connect a 50mm fan to it.

Simple but effective led holder, i use them with SMD2835 Light Strips with double sided tape. may fit other brand, as it use only one track to hold! ... Include both side, printable in less than 1 hour

<p>A remix of the original universal dual fang shroud from K2van. This version has holes added to lower the weight, and the bar that holds it up has been lengthened to ensure stability when it is in in the most extended position. ...I find that the...

I like the look of the blue LED, but it's rubbish to actually see the print. A fan duct seemed the ideal starting point for adding more! The original fan duct design from Kroffty is amazing. I just added the ability to put some cheap LED lights from...

Danger: Currently, my ABL is messed up. Maybe wait for next version, if you do not want to use a file. This remix of mine comes with a complete source file, so you can make your own version with your favourite type of insert or whatever. Main...

Did a quick design for adding the older creality style hotend to the CR6. I printed it out to make sure it all fits. Be sure to add a washer in-between where the hotend adapter bolts onto the metal bracket create a gap for flexing. Just wanted to...

Did a quick design for adding the older creality style hotend to the CR6. I printed it out to make sure it all fits. Be sure to add a washer in-between where the hotend adapter bolts onto the metal bracket create a gap for flexing. Tested it,...

Just a simple cover for a 40mm fan with the Creality logo from the front of the CR6-SE (very hard to find that logo too as most are just the triangle). There are a few versions with different thicknesses, the option of clips and different...

when i was browsing for light bar for the CR6-SE i didnt find any i liked so i designed this one.its pretty stright forward to print unless your bed doesn't fit the one peice bar, so i split it in two. i did this and super glued it and it works fine....

It only add 3 holes to add magnet 8mm x 3mm to use with creality laser head. ...

I've used it with my Creality CR-6 and it fits perfectly. You can see more (and better) photos in my posted make. Mine is printed in PETG for better heat resilience so it will come out looking nicer in PLA! You can see how I used it here...

I made an alternate version of this thing https://www.thingiverse.com/thing:4594168 to use a cheap LED strip as a light-bar on my Creality CR-6 SE and needed a way to route the switch. You can see better pictures in my posted make. The improvement in...

This is a very quick remix of the following: Malolo's screw-less / snap fit Raspberry Pi 3 Model B+ Case & Stands by Malolo https://www.thingiverse.com/thing:3719217 Creality CR6 CR-6 SE Under-screen / Side Rail Raspberry Pi Model B 1 2 3 Case" by...

I'm not much of a designer (check those damn ducts) but I think I have some good ideas and this is one of them. This is meant to provide more air to cool the parts, being a free upgrade if you are using other fans and have the original blower...