creality cr6 se upgrades 3d models

Here is a quick upload of my direct drive for the CR6, its a bit more of a complicated direct drive conversion compared to my last direct drive setup, but I wanted to make the best direct drive X axis setup I could while maintaining the CR6 design...

Hardware Needed: (6) M3x4x5 Threaded Inserts (2) M3x6x5 Threaded Inserts (If using my adaptor remix) (4) M3x12 (2) M3x20 (1) 4020 Radial Fan -...

4020 fan adapter that fits inside the original CR6 hotend cover. Provides a lot more airflow so the fan doesn't need to run at 100% all the time (40% is about the power of the original fan). It is required that you remove the upper part of the...

You'll need these - [M3 tap and drill bit that is a bit...

This is a filament guide for the cr-6 se factory filament sensor. There is a roller with or with a bearing. The roller that needs a bearing you use a 608 bearing. Need to use a m4x16 bolt and nut. There is a shoulder bolt and nut included. I...

Version v1: Fits with creality extruders and Extruder motor up to 30mm legth Version v2: 90degree Turned version. Fits with the Original 40mm Nema 17 Stepper and alternative Extruders. Remark: I relised that crealitys extruders are a flatter...

Attention, je n'ai pour ma part par réussi à faire fonctionner la platine avec le moteur d'origine Nema par Creality. La connexion des enroulements est différente des Nema d'origine ce qui m'a fait cramer la carte servo42c. Ainsi je recommande...

This is a remix of: https://www.thingiverse.com/thing:4763254 This is a fan shroud duct and cover the CR-6 SE. It uses a 40x10mm 24v fan and will direct cool air all around the nozzle. Requires a 40x10mm or 40x20mm 24v fan. Print front facing...

THIS IS A RUNOUT SENSOR MOUNT FOR THE CREALITY CR6 RUNOUT SENSOR FROM AMAZON. THE MOUNT REPLACES THE FILAMENT DRIVE MOTOR WHEN SWITCHING TO A DIRECT DRIVE SETUP, HOWEVER IT COULD STILL BE MOUNTED DIRECTLY BELOW THE FILAMENT DRIVE MOTOR. SIMPLY USE...

Feel free to add to them! i dont use all of these at once,, i recomend the M3 bolts instead of pins but doesnt matter just may last longer! Hello and thanks for shopping..100%discount here! I accept donations toward making prosthetics! Please if...

Creality CR-6 SE Cable Support

As any owner of a Creality CR series printer will be happy to tell you, the filament sensor is located so closely to the extruder that if it does detect a break or the filament runs out, it's very hard to recover from it because there's no room to...

For Creality Dual Gear ExtruderJust a remix that I made because i was getting slight problems with the actual model. Reduced the size a bit and made it simplier in the exterior (just for looks, not functional but might save some filament). The...

For Creality Dual Gear Extruder Just a remix that I made because i was getting slight problems with the actual model. Reduced the size a bit and made it simplier in the exterior (just for looks, not functional but might save some filament). The...

This is a remix of: https://www.thingiverse.com/thing:4669438 I used DFAM techniques to make it more printable adding vertical slots instead of horizontal, as well as adding more slots for cooling. ... Print front side facing down with supports...

A small bracket to support the bowden tube as it enters the hotend to prevent the "weight" of the bowden tube from tripping the ABL sensor during homing and ABLing.

Greetings, As a newbie in 3D printing, I ordered a fillament kit from Labyist, and unfortunatelly, the inner filament spool inner diameter was too small to fit on the standard holder... So instead of shipping it back, why not designing one...

<p>Flag of the Czech army.<br>The flag is adapted for use on CR6SE.</p><p>Printed flag up and without supports.</p><p>The filament colour change on 4.68mm.</p><p>Glued with hot melt gun.</p><p>&nbsp;</p>

Cr6se Simple Tool holder V.1 no sd card V.2 with sd crad fix usb port

Here is the a daughter board case with a led strip holer. I used this 5v COB LED Strip https://a.aliexpress.com/_mMf0gqF The case is a little lower than orginal, so you might need shorter skrews. ...

This is essentially a remix of [3147295](https://www.thingiverse.com/thing:3147295) that moves the PiCam closer to the Z frame and hangs the PiCam under the mount. This works with a [PiCam...

<p>The simple LED light bracket that fits my Led tube light from the old fish tank (aquarium)</p><p>Print:&nbsp;</p><ul><li>At any quality</li><li>Supports for R and L parts</li><li>Infill: 20%</li></ul><p>Remixed from: <a...

I´ve changed the original one by Thr333DDD a little bit. The top adapter hasn´t a longhole anymore, hexagon for nuts and thicker for more stability. The mid adapter is only thicker. It´s not neccessary to extend the cable ! Absolutely maximum...

#1 - SD Card Holder = 4 x Micro slots, 4 x SD slots & 2 x USB slots #2 - 3D SD Card Holder 5xSD 4xmicro = 4 x Micro slots & 5 x SD slots #3 - SD Holder 8xSD 4xMicro = 4 x Micro slots & 8 x SD slots Rail Filler Short Holder fits #1 & #2 ...

Based on Icelandian's awesome filament redirect project, these new sensor housing and redirect things let you the move the spool to the top of the printer and feed the filament through a Bowden tube down to the z-axis assembly.I used Icelandian's...

I just extended it by 2mm so that the top of the blowers would be just at or under the Silicon Sock. In the process of printing to test it. Since this is my first remix I'm not even sure it'll work properly, so proceed on your own. Edit: Yellow is...

Designed this fan duct because I didn't like the gap causing air to flow down on part. The part fits very nicely on to heatsink and I have seen a difference. Also working on a way to isolate air from heatsink hitting the mounting plate and ejecting...

Our favourite printer modifications are often those that make our printer more quiet. This one was inspired by someone observing that although the stock hotend cooling fan can be noticeably loud when installed, it is quite quiet when just hanging...

This is essentially a remix of 3147295 (https://www.thingiverse.com/thing:3147295) that moves the PiCam closer to the Z frame and hangs the PiCam under the mount. This works with a PiCam v2. Note: You will probably want to focus the PiCam with the...

Simple remix of led light holder that fits my Led tube from the old fish tank (aquarium) Print: - At any quality - Supports for R and L parts - Infill: 20%