creality cr6 se motherboard 3d models
56457 3d models found related to creality cr6 se motherboard.
myminifactory
My Printer sits in a dark area of the studio, and I found it hard to see the SD slot on the front. So, this was born. ...It's a silly item and might not even stay on that great, but hey, it's free and uses hardly any filament at all.
thingiverse
A larger knob to go over the tiny X & Y adjustment knobs to allow a finer touch when adjusting.
cults3d
A larger knob to go over the tiny X & Y adjustment knobs to allow a finer touch when adjusting.
thingiverse
A simple support to lessen the strain on the printer spool holder with 1KG rolls
thingiverse
My Printer sits in a dark area of the studio, and I found it hard to see the SD slot on the front. So, this was born. ...It's a silly item and might not even stay on that great, but hey, it's free and uses hardly any filament at all.
thingiverse
Since I don't have enough space on my table, I want my PLA spool to be on top of my printer. ...Super Simple, don't need any screws, compatible with the pool holder piece that comes with the printer.
cults3d
This is a mount for Raspberry Pi-Camera to the Creality CR6-SE printer.
thingiverse
This is a mount for Raspberry Pi-Camera to the Creality CR6-SE printer.
thingiverse
Here is another version of a drawer insert for the Creality CR6 SE. ...
thingiverse
Main design derived from Florent_Degouve's "[CR6-SE] Improved original case" Uploaded to tinkercad, filled in the openings as best i could and hollowed out with the logo i swapped in from michaelbourque's "CR-6 SE Logo" on both fan ports. ... Probably...
prusaprinters
This is a mount for Raspberry Pi-Camera to the Creality CR6-SE printer.Print SettingsPrinter: CR6-SERafts: NoSupports: NoInfill: 20Filament: Greetech PETG black
thingiverse
Tapo C100 Camera mount for the Creality CR6-SE, Fits onto the front of the printer frame. ...
thingiverse
You need the Noctua 60x25mm Fan and a Step-Down for 24 to 12v Just Plug in the Fan and mount it like before, you also can use more spacers on the Ground for more air vantilation
thingiverse
Made a few tweaks to fit 92mm fan: 1. Further increased the width of the rim to fit 25mm thick fan 2. Replaced the fan mounting for 92mm fan. I used a noctua B9 but I think any 92x92x25 fan would fit. 3. Removed the internal ridges to make room...
prusaprinters
... too short. ...Update: Added a support arm to stop the sag. Print Settings Printer: Creality CR6-SE Rafts: No Supports: Yes Resolution: .20 Infill: 15% Filament: GENERIC PLA Any Notes: Support the overhangs.. ...or not Category: 3D Printer Accessories
prusaprinters
CR6-SE LCD Cover - HalloweenThis is a Halloween themed LCD cover for the Creality CR6-SE 3D Printer.The Frame should be printed face down without supports.Individual objects need to be super glued.Please, consider subscribing to my YouTube Channel...
prusaprinters
CR6-SE LCD Cover - SteamPunkThis is a SteamPunk themed LCD cover for the Creality CR6-SE 3D Printer.The Frame should be printed face down without supports.Individual objects need to be super glued.Please, consider subscribing to my YouTube Channel...
prusaprinters
CR6-SE LCD Cover - FootballIts Football season so I created an American Football themed LCD cover for the Creality CR6-SE 3D Printer.The Frame should be printed face down without supports. The end zones should be printed in your primary team...
thingiverse
2020/11/29 v1 Just the original Creality CR6-SE case with improved opening for fans ----- 2020/12/06 v2 Improved hardness and design ----- 2021/01/07 v3 Increase in volume for mounting a 40mm heat break fan and addition of protective grilles -----...
thingiverse
A filament guide for the Creality CR6 SE. This is to be used without the filament sensor. Mine went out so I just bypassed the sensor and designed this. I have included 2 different outer surfaces for the bearings, one is slightly bigger than the...
thingiverse
This is a mount for the Slice Engineering Mosquito hotend for the Creality CR6-SE. The mount takes advantage of the Slice Engineering E3D circular groove mount adapter. Use M3 brass inserts for mounting to the load cell. The stock fan...
thingiverse
Spool holder for the CR6-SE that holds both small and large spools, as the one that comes with the printer will not take Small spools.
thingiverse
I took ThePizza's attachment for the CR6 Max and adjusted the dimensions to fit easily on the rails for my CR6 SE. I then took the arm design from CasperVerswijvelt and modified it to fit a folded Logitech webcam and attached the modified clip. ... ...
thingiverse
Slightly longer spool holder to fit onto the original CR6-SE spool arm.I found that the position of my holder was just a little too short. ... Update: Added a support arm to stop the sag.
thingiverse
Simple clip to attach the Bowden tube to the braided ribbon cable on the CR6 SE replacing the stock black ones that don't really work. This print should help prevent the ribbon cable being a fatigued. ... Plus it just looks pro
thingiverse
CR6 SE Rear Ribbon Cable Tidy. A simple bracket that clips into the extrusion in the same way as the stock filament holder. Keeps the ribbon cable nice and neat and away from the Spool. Hope it Helps, hit like if you like it! ...
thingiverse
Remade Dr Boo's CR10 squash ball feet with a pocket to fit the CR6-SE feet instead of the screw holes to fit the CR10. They are not a very tight fit as I wanted to be able to easily remove them. ...I held them in place with a dab of clear Bostik glue...
thingiverse
If you are like me and absolutely hated that blue LED on the CR6-SE... Then fret no more! I designed a simple holder to suit a white, 5mm LED. Just be sure to wire in a resistor. ... I accidentally snapped the rear clips that held the original LED in...
thingiverse
This is a remix of 3dFreezeMe's awesome extended orbiter mount for the CR6-SE (https://www.thingiverse.com/thing:4818983). The only issue I had with the original is that the orbiter extruder keep giving me problems, so I decided to bite the bullet...