creality cr5 pro 3d models

This is a left front mount for a Creality Camera that works with the Creality Box 2.0 . I have not tested it yet I will upload pictures as soon as I have printed and tested it. UPDATE : Print the bolt part in 100% infill as it breaks off...

... original so if look is important, use that one. ... this is a stronger, more stable version, so if that is a thing for you, have a look here :-) Same holes, same height, fully Creality standard, they use the same metal bracket for all their printers.

... SD card along with the rabbit, car etc. ...Uploading it here as some customers reported their SD card doesn't have it included. There are two holes underneath the bed that it attaches to, using the spare screws provided by Creality with the printer.

Modified clip upgrade for the latest Ender-3 or Ender-3 Pro 3D printer kits featuring dual Ø4mm diameter power cords, effortlessly detachable using a flathead screwdriver on aluminum profiles.

I made the model to adapt it to ender 3 or pro. ... You'll have to cut 1cm from the chassis to better route the cables, then also on the power button.

This is just a small spacer for DWS's draw set for the Ender 3 Pro (https://www.thingiverse.com/thing:3416444). It essentially converts the box to fit a standard Ender 3. ...

A must-have accessory for Ender 3/Pro enthusiasts, this handy tool box provides ample storage for the printer's included tools and offers additional room for personal favorites. ...Conveniently secured by two screws at the top right corner.

Direct Drive Extruder installed on my Cr10s Pro I made this base to fit my printer with this excellent Orbiter 1.5 extruder. ... With this base you use the same screws as the base to use the stand.

Modified clip for the new Ender-3 or Ender-3 Pro 3D printers kit with 2x Ø4mm diameter of the power cables. ...Very easy to remove clips from an alu profile with a flat screwdriver :)

This is the right (switch) side for a replacement for the stock ender 3 s1 pro light or the light kit. ...Original model at thangs.com: https://social.thangs.com/m/974694

These clips enable users to relocate their power supply unit on an Ender 3 Pro, freeing up space for adding a secondary Z-axis stepper motor in support of a Dual Z-axis upgrade.

I designed a custom QR code cover with the T2 logo on it, specifically tailored for my Ender 3 Pro 3D printer. ...The blank cover was downloaded from Nobble's design on Thingiverse, reference number 3317795.

The need for hot-end wire management on the CR-10S Pro has never been more obvious than after installing Micro Swiss hot end, BL Touch and Klipper running on a Duet Mini 5+ with the ability to print ludicrously fast. ... The bracket needs to be...

https://paypal.me/cdsmakestuff Creality Ender 3 / Pro / V2 (?) --- I can only assume this could work for the V2... don't have one to test with. Part Cooling / Hotend Cooling - Upgrade "Kit" Very lightweight --- Original steel fan support and part...

https://paypal.me/cdsmakestuff Creality Ender 3 / Pro / V2 (?) --- I can only assume this could work for the V2... don't have one to test with. Part Cooling / Hotend Cooling - Upgrade "Kit" Very lightweight --- Original steel fan support and...

Orbiter v1.1 and v1.5 adapter for Creality Ender V2. [Join our Facebook support group!](https://www.facebook.com/groups/705637896767655) Updates: 11.02.2021: Uploaded adapter for Orbiter v1.5. 15.02.2021: Uploaded new adapter version for...

Started with Pen/Pencil/Marker mount for Creality Ender 3 / CR-20 by urish (https://www.thingiverse.com/thing:3139205) and found that the connection to the print head was too flexible. Designed this holder with two pieces that attach together with...

... ...This happened when the extruder came down and hit the spool. Even whit the holder all the way back of the printer. This part prevents that and the spool from coming out of its place. 3 Pieces. It works with all the creality standard spool holders.

Da mir das original Board zu laut war habe ich ein SKR PRO eingebaut. Bedient wird er normalerweise über Repetierserver daher bekam er nur das kleine Display da mir die Bedienung mittels Knopf auch viel besser passt. USB wird verlängert und nach...

... that impact the ring angle. On my ender 3 pro with the 90° original angle the ring isn't horizontally aligned with the print head, i have corrected this with a -2.5° correction. I don't know if it's specific to my printer or if it's general. ...

I upgraded to an SKR PRO board as the original one was too loud. It's usually controlled via Repetier server, so I only gave it a small display since navigating through buttons works much better for me. The USB cable will be extended and pulled...

Cr10s pro için çizdiğim kamera tutucu. x ekseni gerdirme tarafına yazıcının ön kısmından ittirilerek montaj yapılabilir. Kamera vida yerini boş bıraktım yakın zamanda ona da vida çizip yükleyeceğim ama bu haliyle de sıkı geçme geçiyor kamera,...

For Reality CR-10 Smart Pro is the alternative end cap for the spool roller with a diameter of 50mm. Using the hexagon key from the printer kit, unscrew the screw and remove the standard cap, then replace it with the printed one, screw it in.

I was on the hunt for a custom power supply cover for my trusty Ender 3 Pro, but nothing caught my eye, so I took matters into my own hands and created this one myself - a sleek slip-on cover that's both functional and visually appealing.My first...

This allows you to attach a bowden tube to your filament sensor on your CR-10S Pro, no drilling or tapping required. Makes it much better to put your roll of filament where ever you want, and makes the transition smoother. Print it at 100%, it snaps...

I made it easier to print the Creality logo in a different color and changing tool configurations and sports. I took out the scraper because i use a much better one thats too big, but i included a file with one anyway. My changes were spaces for...

There are other guides but I could not find a filament guide that fits with the Creality filament break sensor mounted.Here are the list/qty of the parts needed or to be printed: The Main Bracket - Print x1The Outer Ring - Print x1 The Innser Ring -...

It essentially performs the same function: It securely holds the tool set of the CR-10S Pro along with some additional tools and wraps snugly around one of the rubber legs, also catching behind one of the screws that retains the bottom of the printer...

I love the original design, but I had two major issues: 1) The initial magnet size wasn't readily available on Amazon, so I swapped them out for 0.5in (12.7 mm) magnets from Michaels craft store...

When looking for a simple and effective design for squash ball feet for my Ender 3 S1 Pro, I couldn't find many models that I liked. Many of the models required modifications to the printer that were irreversible or seemed too flimsy for what I...