creality cr20 3d models

// ENGLISH Camera mount for a Creality CR20. Securely fastened to the printer with a small drop of hot glue. Designed in two separate parts, a support and a base, for easier printing and customization. You can create your own personalized base...

... but has only been tested on this specific device. ...The camera mount is situated at the front of the printer on the Y-axis as shown in the provided image. This print was created with one side facing downwards and supported by the Creality CR20 Pro.

in the download you'll have the blanl ones, or with the "CR20" text)This frontplate can be used to give your Creality CR20 and CR20 PRO printer a different look and feel. And it's a reminder of which way to turn for the Z-offset ;-) The plates with...

This is a "Remix" of the WebCam Bracket by ClassicVAG I bought an EKEN H9R action cam for my timelapses and combining the CR20 mount with a custom base made for the dimensions of this camera, i "create" this. ... Enjoy

This is a "Remix" of the WebCam Bracket by ClassicVAG I bought an EKEN H9R action cam for my timelapses and combining the CR20 mount with a custom base made for the dimensions of this camera, i "create" this. ... Enjoy

... WebCam Bracket by ClassicVAG. ... I recently acquired an EKEN H9R action cam to capture high-quality timelapses. By combining the CR20 mount with a custom base tailored specifically for the dimensions of this camera, I designed this innovative setup.

Adapter_Redrex__Dual_Extruder Creality CR-20 Die Schraubenlöcher wurden versenkt, damit die original Schrauben weiter verwendet werden können...

Remixed to suit a Creatliy glass bed. Smaller gap and printed in ABS. ...So far hold the bed very tightly.

Based on Marlin 2.0.5.4 Drivers and software included. Functionally tested. - PrusaSlicer or other software can also be used to flash the firmware. - If EEPROM error, perform an M500 with Pronterface. - Endstop software enabled, to make Zoffset...

The case accommodates PCB boards that snap into place inside it, offering two mounting holes or tabs specifically designed for the Creality CR-20 printer. It's possible that other printers may also be compatible, but I'm unsure which ones. The...

... the minuscule microSD card. The adapter is slid into the clip which (without screws) is clicked on a Creality CR20 or Ender 3 Pro. ... You can find the cable here https://nl.aliexpress.com/item/32821019448.html?spm=a2g0s.9042311.0.0.758a4c4dOONhGy

Here's the deal with human remixes and Creality Fanducts - they're basically a game-changer for 3D printing. Just take a look at this thing on Thingiverse, https://www.thingiverse.com/thing:2969101. ...It's a total hack of the original design, tweaked...

<p>To mount the pen holder, screw it under the original part cooling fan.<br><br>Remixed from <a href="https://www.thingiverse.com/thing:4924000">this thing</a>, because I had Problems with the pen wobbling on the paper. ...This version does'nt include...

Metal Extruder Cable Manager for Creality CR20 Pro, will fit most of the Creality models and probably others as well. ...For the insert used a 50% infill to make sure while sliding in and out the edges will not be chocked.No other modifications needed ,...

... getting tangled and caught. ...This simple precaution will save you a world of hassle in the long run. Tested on a Creality CR-20 Pro, but I'm confident this trick will work just as well with an Ender 3 or any other printer that needs a little TLC.

To get the belt path aligned better with the parallel orientation, we need to tweak the setup to ensure consistent tension throughout the entire X-axis motion.

This should fit Creality CR-10, CR-10S, CR-10 4S, CR-10 5S, CR20, Ender 5, Ender 3 I used this with E3D Hemera XS Revo on an Ender 3 Pro, with [this fan duct (5015 blower)](https://www.thingiverse.com/thing:5427294) ----- I attached Joe Casha's...

This is a filament runout sensor with a roller that uses the stock z-stop switch of the Ender series printers (you don't need it if you have updated to bl touch). It does not need any additional parts and is 100% 3D printable. You will need: -...

This is a damping system designed specifically for the Creality CR20 and CR20 PRO 3D printers.

This is a replacement dampening system designed specifically for the Creality CR20 and the upgraded CR20 Pro 3D printers.

User is utilizing a modified version of the Creality CR20 and CR20 Pro 3D printers, SKR 1.4 board equipped with two modifiable offset sensors.

Printed and then installed on Creality CR20-Pro, using 3DPrintz Black PLA. ... Sliced using Cura 4.9 - using Fast settings : 0.28 Layer Height 4 Walls for strength 15% Grid Infill Support (only for > 50% - for the hole in the model) Bed...

This is a mounting solution for those that are using the BTT_tft3.5v3 touchscreen on a creality Cr20. You will also need to purchase, or have short #4 self tapping screws to secure the screen to the mount. The case is designed to snap into the...

This print is used to retrofit a usb c and micro sd card extender in the creality cr20, using the existing holes in the case, when using a different mainboard. This can be printed without supports and on its end. The skr 1.4 uses a usb b connector so...

Ready to go bracket to mount an BigTreeTech SKR1.3/1.4 mainboard inside a Creality CR20-Pro machine.Feel free to adapt the STL to fit your printer. This bracket can hold the SKR mainboard, 2x Stepdown converters, 1x Fan turbine and a whole bunch of...

This is the CR20 a ship that appeared in the original 2003 clone wars series. I would imagine this ship appearing in the table top game Star Wars Armada. ...This is a flotilla style ship for the Republic Faction

This is the CR20 a ship that appeared in the original 2003 clone wars series. I would imagine this ship appearing in the table top game Star Wars Armada. ...This is a flotilla style ship for the Republic Faction

The CR20 power supply puts out a steady 24v. A LM2596 step-down converter is being used to provide a reliable 5v power source for my raspberry pi, which runs the octoprint software. I've got a link to the specific LM2596 adjustable DC-DC converter...

I'm creating a cable management system for my Creality cr20 pro by attaching it to the bed bracket using Ender 3 Cable Chain, which I modified to fit by widening the last link holes with a 4mm drill and replacing the back corner case screw with a...

The design clamps securely over the standard spool roller (Creality Cr20 Pro) and is firmly screwed in place by connecting the top and bottom components using (3x12 mm (8x) and 5x35 mm (2x)) threaded fasteners. This setup ensures that none of the...