creality cr 6 se 3d models

I've tried adding LEDs to a few different fan ducts that go around the hot end and blow air down instead of the stock system and they've all worked really poorly - but I still didn't want the stock blue LED. I came up with this small adapter that...

This is designed to be clipped on to the modified filament sensor case here https://www.thingiverse.com/thing:4635094 and it will direct the cable over the extruder instead of down the side of it. I have not printed/tested this, but it should work...

See my make for more photos. This thing was inspired by this thing https://www.thingiverse.com/thing:4688169 but I made it all from scratch and it's quite different. It's only 38mm by 28mm as that's the only space I had behind this drawer for...

This isn't really a remix, but additional plates to cover the wires after installing arkworkvideos excellent Power Supply Cover for the CR-6 SE. I didn't like have any wiring exposed - especially mains. There are two versions - just two flat...

I've used it with my Creality CR-6 and it fits perfectly. You can see more (and better) photos in my posted make. Mine is printed in PETG for better heat resilience so it will come out looking nicer in PLA! You can see how I used it here...

Just a simple cover for a 40mm fan with the Creality logo from the front of the CR6-SE (very hard to find that logo too as most are just the triangle). There are a few versions with different thicknesses, the option of clips and different...

It only add 3 holes to add magnet 8mm x 3mm to use with creality laser head. ...

Make sure you follow a guide to tune your PID afterwards using something like this https://matterhackers.dozuki.com/Guide/PID+Tuning/6 (I used a temp of 215c and 10 runs). UPDATE: I added a tiny hole going down the thin tube on the inner part...

This is a very quick remix of the following: Malolo's screw-less / snap fit Raspberry Pi 3 Model B+ Case & Stands by Malolo https://www.thingiverse.com/thing:3719217 Creality CR6 CR-6 SE Under-screen / Side Rail Raspberry Pi Model B 1 2 3 Case" by...

It will fit into any rails that are the same as the CR-6 - but you may need different lengths of V-slot covers. I'd advise using a 10mm v-slot cover between the front of the rail and the raspberry pi case so it's not pressed right up against the...

Props to the original maker. I remixed the long version of the original drawer to have a flat front and a stronger handle - just like my right-side remix here. https://www.thingiverse.com/thing:4703142 You can see my matching right-hand drawer...

All I did was add a chamfer to the handle of the original remix to make it stronger. I printed it with a 1-4mm chamfer, but when it came out I wish I'd used a 2-4mm chamfer to make it more pronounced/stronger. If it breaks I'll print the newer one! ...

See my make for more and better photos. I didn't like the idea of having to have my motherboard fan on full power all the time - but the stock one was tiny and noisy. I discovered that Arctic Cooling make a very cheap (and quiet) 92x25mm 12V fan...

<p>I'm not much of a designer (check those damn ducts) but I think I have some good ideas and this is one of them.</p><p>This is meant to provide more air to cool the parts, being a free upgrade if you are using other fans and have the original...

This is not really a remix, I just added a couple of bits onto the already excellent design. I modified the cover that clips onto the x-axis stepper motor by adding the camera mount from my thing here https://www.thingiverse.com/thing:4654989 (you...

I printed the original thing this is remixed from in PETG, so it looks pretty blobby etc, but it's strong stuff - however, I'm using it with a 4020 fan instead of a 4010 fan and within about an hour the weight had made it start to droop and it was...

https://www.youtube.com/watch?v=B6ID1zSqvd4 This is a combination of this https://www.thingiverse.com/thing:1258498 and this https://www.thingiverse.com/thing:4620590 - but both were highly modified. The end cap of the stepper seemed like the...

I'm not much of a designer (check those damn ducts) but I think I have some good ideas and this is one of them. This is meant to provide more air to cool the parts, being a free upgrade if you are using other fans and have the original blower...

This cover is great, but it doesn't work if you use a 40mm hot-end cooling fan. Basically all I did was chop a chunk off the side to account for the larger fan. I also wanted to be able to mount an LED strip to the side of it instead of the awful...

This is not the slightest bit original. RICBRU did all the work. I just wanted a top without a logo hole that would allow dust etc in and I also wanted PTFE instead of printed lines for the filament to go through the exit into the extruder. I...

I basically made the fan duct stronger in a few weak areas, made it easier to print, moved it down and changed the angle a bit (to get my 4020 fan to fit under the bed levelling sensor wires). I made the mounting bracket massively stronger and...

I remixed my remix to improve on the design. This one is taller (goes further down), has a base and positions and angles the LED strip better. It still includes the cut-out for a 40mm fan, but this one interferes with the bed sensor less. I used a...

Creality Sonic Pad mount for CR-6 se

Add the Creality font to your CR-6 SE bed plate in PrusaSlicer. To install the .svg file in PrusaSlicer: 1. Click on Printer Settings tab. 2. Under General, click the Set button next to Bed shape. 3. Under Texture, click the Load button. 4.

Filament spool holder remix for CR-6 MAX

Silicone Heat block mold for CR-6 SE. Printing Information The inner part needs support. Other can be print without it. To Inject the silicone - Soak all mold parts in a bath of 1/4 water 3/4 dish soap - Assembly the mold wet - Lock the...

Good day,Welcome to my profile, full of models and miniatures :-)I have a cable for profile 4040 for the Cr6 Max printer.This is a possible solution if you destroy the original staples and you like the original instead. ...Made of PET G and is much...

Good day,Welcome to my profile, full of models and miniatures :-)I have here for you an original solution for holding the cable from the bed to the motherboard for the Cr6 Max printer.You will need an M3x10 screwPrinted without supportsHave a nice...

Using some models of thingiverse i modify to adapt in Creality CR-6 SE.

Cable clip for Creality CR-6 SE, with 2x3mm holes added to attach objects to it.