creality cr 6 max 3d models

Cr6 extruder is converted as a direct drive with this project. ...(V2)

I made an alternate version of this thing https://www.thingiverse.com/thing:4594168 to use a cheap LED strip as a light-bar on my Creality CR-6 SE and needed a way to route the switch. You can see better pictures in my posted make. The improvement in...

This is a M10 threaded remix of K2Van's excellent CR-6 hotend with WhatWouldAnEngineerDo's two-part modification. I've personally found the two-part version to level more reliably using the CR-6 strain gauge than with the original version. I've...

14.12.2023 Обновил до версии v5.Вариант минифидера под штатный мотор.Адаптирован под родную 12-зубую шестерню мотора, все крепится на штатные места.В комплекте адаптер для обрезания трубки под нужную длину: Вставляете трубку в фидер до упора,...

I wanted a SD-Card Holder for normal sized SDs for my new CR-6 SE. This is an easy print, just make sure bed adhesion is good so that the part not warps. It can be installed with the two stock screws that keep front cover attached to the left 40x40...

I wanted a SD-Card Holder for normal sized SDs for my new CR-6 SE. This is an easy print, just make sure bed adhesion is good so that the part not warps. It can be installed with the two stock screws that keep front cover attached to the left 40x40...

This isn't really a remix, but additional plates to cover the wires after installing arkworkvideos excellent Power Supply Cover for the CR-6 SE. I didn't like have any wiring exposed - especially mains. There are two versions - just two flat...

It only add 3 holes to add magnet 8mm x 3mm to use with creality laser head. ...

Upgrades on my CR6SE: === Micro Swiss Dual Gear Extruder Micro Swiss All Metal Hotend Kit CR-6 SE/Max Micro Swiss Plated Copper High Temperature MK8 Style Heater Block Upgrade 255x245mm PEI Magnetic Spring Steel Build Plate for CR-6 SE 0.4mm MK8...

This is a simple spool holder for the CR-6 SE. The holder is just the actual holder (not the arm) and is almost an exact replica of the one the printer comes with. You can see the difference and similarities between the original (right) and the...

Here's why: Built on marlin 1.1.6 Has bed aligned correctly. Temperature protection turned on (no house fires). REALLY, ANET DISABLED THIS OPTION!!! Easily add BLTouch. Turns your ANET E10 into a CR-10 stock firmware. REMEMBER TO ADJUST YOUR FLOW...

Edited the holding brackets for Anycubic i3 mega to support a 5W LED bar, model: X4-LIFE-701572 on the top frame of the Creality CR6-SE. It fits perfectly and it does not affect the print height of the printer. ...

Upgrades on my CR6SE: Micro Swiss Dual Gear Extruder: https://www.bastelgarage.ch/micro-swiss-bowden-dual-gear-extruder Micro Swiss All Metal Hotend Kit CR-6 SE/Max: https://www.bastelgarage.ch/micro-swiss-all-metal-hotend-kit-fur-cr-6-se-max Micro...

Here is a bigger version of gulfcoast_robotics' handle bar freshly modeled and sized for the CR-10 Max. ... I'd suggest support on this one, and you'll need the Max to print it due to its size.

Just a simple cover for a 40mm fan with the Creality logo from the front of the CR6-SE (very hard to find that logo too as most are just the triangle). There are a few versions with different thicknesses, the option of clips and different...

Creality CR-X Support for CR-Touch

Creality CR-X Support for CR-Touch

Make sure you follow a guide to tune your PID afterwards using something like this https://matterhackers.dozuki.com/Guide/PID+Tuning/6 (I used a temp of 215c and 10 runs). UPDATE: I added a tiny hole going down the thin tube on the inner part...

Je to moje první dílo. Já jsem to vymyslel a přítel na dálku z Bostonu mi to vytvořil v CAD programu. Moc mu za to děkuji a věřím, že vytvoříme další kousky. :-) It's my first work. I invented it and a friend at a distance from Boston created it in...

just print 2pcs x 85mm or 1ps x 170mm /slot. just snap it in from top without need to open the screw. if other printer model you can test print the 10mm and test it on your printer v slot. if the cover snap in without any problem than you can print...

Das Teil passt zu der Kette von Thomas Gaillard "www.thingiverse.com/thing:4745917"

You can %98 scale to fit easy, but I tried %100 scale, its OK.

This is a remix from https://www.thingiverse.com/thing:4657122 I didn't like the way the original design of this hot-end cable guide forced this cable to be twisted. So I redesigned it. There are two versions, one without the PTFE bowden tube...

This is a very simple remix. All I did was trim it a bit where it clipped over the metal frame so I could use my own PTFE support with the part-cooling fan bracket that you can see here https://www.thingiverse.com/thing:5406079 - I've discovered that...

Hello, petit cache de protection, pour cacher se moche câble.

You need the Noctua 60x25mm Fan and a Step-Down for 24 to 12v Just Plug in the Fan and mount it like before, you also can use more spacers on the Ground for more air vantilation

My first attempt on making a 3D-model. I ended up with making two alternative printer feet. One to just put on the original feet on the printer, and one to slide on to the aluminium profile. The last one are a more safe foot since it is locked to the...

Mounting the webcam to the bed provides nice smooth timelapse videos using octoprint as the model is always in the same position relative to the camera. This bracket attaches to the steel plate underneath the bed. It can be positioned at front or...

I do move my 3D-printer and there is always an possibilty I change my belt knobs - which is totally annoying. I made a fix for that. ... I printed it as showed with tree support inside in PLA