creality cr 200b upgrades 3d models

I measured it for mounting on the CR-200B without the metal shroud cage. In the picture, I mounted using the angled version which allows a view a little from above. I've included the flat version where it will provide a flatter view giving you a...

Part cooling duct upgrade for CR-200B. Directs airflow more at nozzle. Uses all stock screws to mount. I am using a Microswiss all metal cr10 hot end mounted as stock hot end is same length within a few mm so duct should work with stock hot end...

My Printer: Creality CR-200B Creality Sonic Pad Phaetus Dragonfly BMS CR-Touch

<p>Espaciador fabricado en PETG, se puede utilizar PLA, ABS….</p><p>Relleno 15%</p><p>&nbsp;</p><p>Imprime con moderación.</p>

Better fan for CR-200B 4020 Fan: https://www.bastelgarage.ch/creality-4020-bauteillufter-cr-10s-pro-max Printed in ASA: https://www.bastelgarage.ch/easa-schwarz-filament-1-75mm-1kg-esun

Better fan for CR-200B 4020 Fan: https://www.bastelgarage.ch/creality-4020-bauteillufter-cr-10s-pro-max Printed in ASA: https://www.bastelgarage.ch/easa-schwarz-filament-1-75mm-1kg-esun

Remixed the original so that the threading would align with the notches in the back of the Cr-200B (the original was tilted to the side). ...Also put the axle together for a single piece print.

The CR-200B has two fans doing basically one one job. Replace both the 5015 radial and 4020 axial inside the case with a 12V 120mm axial. I mounted pushing air out the bottom so less chance for cool air to introduce into the printing chamber. ...If you...

A bracket that allows the BL bed levelling sensor to be mounted in the same place as the bracket used in the Creality YouTube video from 2021. ...It replaces a piece from the opposite side to the hotend fan.

Shoppping List: CRTouch: https://www.bastelgarage.ch/cr-touch-auto-leveling-kit-fur-4-2-2-4-2-7-mainboard or BLTOuch: https://www.bastelgarage.ch/bltouch-3-1-automatischer-nivellierungssensor...

Shoppping List: CRTouch: https://www.bastelgarage.ch/cr-touch-auto-leveling-kit-fur-4-2-2-4-2-7-mainboard or BLTOuch: https://www.bastelgarage.ch/bltouch-3-1-automatischer-nivellierungssensor...

cr 200b orbiter 1.5 mount

Small bracket to hold the filament runout sensor when using a Bondtech (BMG) extruder on a CR-200B

cr 200b orbiter 2.0 mount. Holes were designed to put a brass inserts. ...The top two holes front side is for 2mm

CR-200B 3D printer extruder stepper motor is encloses without possibility to good disipate heat. ...This model will hold fan near extruder gear.

Bearing retainers for the CR-200B, 3 of mine were broken and 4th one was cracked, Replacing with the brittle under supported ones even if you could find them seemed pointless. I designed these they fit great. You will need to use M3X12 screws for...

Originally designed for CR-200B but I guess can also fit Ender 3 since it has a very similar head design (not the V2!). The fan duct allows to hold a 5015 blower fan which improves a lot the cooling performance compared to the stock 4010 fan. ...

remixed phosperus's carriage for cr 200b to mount orbiter.

I modifed it enough to allow the duct/fan to slide under the CR-200B chassis and enough clearance to avoid the bed retention screw. Check the posted pictures, I was able to fully travel the bed without any hitting anything. NOTE, I reverse the...

Fan duct + Bltouch holder for Creality CR200b. ...Fits both original and dragonfly hotend

... two other peaces. ... So thanks to Fan Holder https://www.thingiverse.com/thing:4950143 by https://www.thingiverse.com/bastelgarage/designs BL-Touch / CR-Touch https://www.thingiverse.com/thing:5243858 by https://www.thingiverse.com/silvianh/designs

Orbiter direct extruder extension for Creality CR-200B

upgrades on Ender-6

upgrades on Ender-6

In order to derive the heat build-up when the 3D-Printer stands on a Wall. I have developed ventilation pipes that derive the heat upwards. ... The tubes can be attached with double-sided tape.

In order to derive the heat build-up when the 3D-Printer stands on a Wall. I have developed ventilation pipes that derive the heat upwards. ... The tubes can be attached with double-sided tape.

In order to derive the heat build-up when the 3D-Printer stands on a Wall. I have developed ventilation pipes that derive the heat upwards. The tubes can be attached with double-sided tape. ...

This is the bracket that works for the CR-200B to mount a CR-Touch and BL-Touch with their included screws.Remember when doing the firmware update to do the Main Board first, then the Display Board. ...Also format your SD card in Fat32 with an...

Due to bed frame is too close to the screws, this spacer helps with the installation of silicon springs on a Creality CR-200B.

Creality CR-10 Upgrade Suite. This kit features an upgraded extruder with enhanced ergonomics and functionality alongside an improved bed level adjustment system. New as of January 25th, 2018 is the inclusion of a E3D-V6 hot-end adapter, which...