creality cr 10s4 3d models

# Printing the parts: I use a Creality Ender 6 with a 0,4mm nozzle and PLA or PETG filament. It is important, that the reflector is printed more or less massive. I use 7 perimeter walls (@0,34mm) and 8 Bottom and Top layers, resolution 0.2mm. For...

But if you use a different printed that requires force, however so little, to remove the print from the bed, then the letters will probably break off. I intend to print this for my Ender 5 with relocated enclosure and self designed lid, with a 120mm...

Printing the parts: I use a Creality Ender 6 with a 0,4mm nozzle and PLA or PETG filament. It is important, that the reflector is printed more or less massive. I use 7 perimeter walls (@0,34mm) and 8 Bottom and Top layers, resolution 0.2mm. For...

But the choice is yours. Enjoy :-) Print instructionsPrint Settings Printer Brand: Creality Printer: Ender 3 Notes: Printed in Real Filament Black PETG purchased from Amazon. Nozzle : 0.4mm Layer Height : 0.2mm Print Temp : 245°C Bed Temp : 80°C...

... Adjustments made. New file added. Needs retesting Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: .28 Infill: 20 Filament: 3D Solutech Printer Filament PLA Light Yellow Category: Toy & Game Accessories

This project took some time and effort to get correct, due to the tight fitting parts, so if you intend to produce these for sale, please contact me by PM for reasonable terms. Print SettingsPrinter Brand:CrealityPrinter:CR10S...

I've seen many controller-board mounts/adapters for fitting an SKR (or MKS) mainboard (four holes in the corners) into a Creality Ender printer. With all Enders, the screw holes are unique for Melzi boards. For mounting an SRK or MKS in an Ender...

.28 layer height. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: .28 Infill: 35% Filament: Any PLA Any Notes: Should work with any stiff filament. Rafts and supports not needed. You may have to...

This is the version i would recommend downloading and using. Note 19/9/18 Two things i forgot to mention. Extruder direction will be reversed when you use this so you will need to either change it in firmware or at the connector. Extruder ESteps...

Compatibility I have only tested this with the following configuration: * Creality Ender 5/Pro * MicroSwiss Hotend (the mounts are the same for the stock hotend, but the blower scoops may not be quite right) * Printermods MDD Direct Drive Kit * Dual...

But 100% fan power isn't necessary, so use an lower Value and take the 100% as "headroom" for bridging etc.The bed leveling is done with an single DC42 IR Sensor (I can highly recommend them). Printing and InstallationAll parts can be printed...

Down here the list of improvement i think to have achieved compared to the Creality standard ventilation system: 1. Left and Right cooling air flow on the print 2. Eliminate the air bleeding on the printed part coming from the hotend cooling fan...

If you have a small printer like me (Creality Ender 3), you have to print some parts WITHOUT rafts!!!You can label the panels by changing the filament at the appropriate print height in Cura (etc.). I only did this for the buttons. I printed the...

I will update the photos once the final print had finished and it is installed :) Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: Yes Resolution: 0.25 Infill: 10% Cubic Subdivision Filament: Polymaker Polyflex PLA...

The printer used was a Creality LD-002H using an eSun transparent red water washable resin with default settings but 20s base layers and 1.8" per layer exposure. I also added a version of the jig that had a 0.6mm chamfer at the base layer - since...

Will order new ones soon. Hardware needed: 1x NEMA 17 Stepper 3x 110mm M5 Threaded rods 2x 120mm M5 Threaded rods 10x M5 Nuts and washers 3x 130mm M8 Threaded rods 1x 60mm M8 Threaded rod 8x M8 Nuts and washers 10x 608 Ball bearings 18x 4mm wood...

It is designed for and tested on the Creality Ender-3 V3 KE. But users told me that the support also fits the SE model perfectly.In any case, use of this accessory is entirely for your own responsibility.The design history of this part can be found...

Print Settings Printer Brand: Creality Printer: Ender 3 Rafts: No Supports: No Resolution: 300 Infill: 15 Filament: Any Any Any Notes: I shaved a ton of time off printing by reducing my tops/bottoms to 2 layers. You can see the infill through this,...

The "regular" files will print on an Anycubic Mega S or an Ender 3 using the "no bed adhesion" setting.A USB flash drive with BATOCERA linux installed. See <a href="https://batocera.org/download">https://batocera.org/download</a> and <a...

However, if you have an Ender 5 (Plus) or other Creality printers, you might want to check out my rail sliding mount for the Hemera. What you need: - Four square nuts inserted into all four holes on the Hemera - Four M3x8mm screws for attaching the...

- Have not tried the sensor with Creality's firmware. Do yourself a big favour and use JyersUI. - Have not used the sensor on a stand alone printer without OctoPrint. Should be fine... let me know please. - My sensor had very high rolling...

But if you have an Ender 5 (Plus) or other Creality printers, you might want to check out my rail sliding mount for the Hemera. :) What you need: the 4 the square Nuts inserted in all 4 Holes on the Hemera 4x M3x8mm for attaching the FanDuct_Mount...

I was fortunate that all 3 units, acquired from the same Amazon supplier eTopxizu 12v 30a Dc Universal Regulated Switching Power Supply), had their tapped holes in the same locations....

I have found the Creality branded fans to be much more robust and better performance than other unbranded items. 4.I have noticed that the LH duct can conflict with Ender 3 Heat Bed cable retention housing at the extreme rear left. This must be...

This Auto Off system was designed and integrated to my Creality Ender 3 V2 printer but will probably suite all Ender 3 family printers as well as similar open frame printers from different manufacturers. The system is an external add-on, there's no...

Because eventually the only things that will end up on thingiverse will be people making STL's of 'Yoda's holding a penis' and IKEA hacks. RamjetX Print Settings Printer Brand: Creality Printer: Ender 3Rafts: No Supports: NoResolution: 0.2...

Feel free to write me your wishes or suggestions on https://www.instagram.com/druckdrei/ to improve your coffee budget.CAD:FreeCAD 0.20Printer:Creality Ender 3 V2Rafts:NoSupports:NoResolution & Nozzle:0.1 mm & 0,4 mmInfill:50%Filament brand &...

... here. https://www.thingiverse.com/thing:4252159Print instructionsUnassociated tags: 3M mask Print SettingsPrinter Brand:CrealityPrinter:Ender 3 ProRafts:NoSupports:YesResolution:0,2Infill:100%Filament: Plasty Mladec, Creality, Gembird PLA - PETG

Please post any makes or questions.Print SettingsPrinter Brand:CrealityPrinter:CR10S PRORafts:NoSupports:YesResolution:0.2mmInfill:38Filament: Duramic3D PETG WhiteNotes:Parts are not oriented for printing. Please calibrate extruder steps and flow...

The electricity voltage in my country is 220V but the voltage that comes to the "on/off" switch is 110V, probably because Creality designed the power supply to be compatible with both voltages; 110 and 220. Nevertheless, when mounting the switch and...