creality cr 10s upgrades 3d models

... and grounds between multiple interfaces. In order to take full advantage of the Duet features I designed the [CR-10S Pro Custom Transfer Board](https://github.com/ReXT3D/cr-10s-pro-mods/tree/duet3d) that allows all signals to be fully independent.

This is a y-axis (bed) sensor mount designed to allow the CR-10S S5 to reach its advertised physical limits of 500x500x500mm. As sold, the bed sensor mount cannot be located far enough back along the v-slot to permit the bed to reach 0,0,0 home...

My bed cable snapped after several large prints, so I came up with this fix for my Creality CR-10s PRO. You can see the broken bed power cord in the picture and video below. The solution involves adding a chain that adjusts the cable angle while...

Creality CR-10s Dial Indicator Mount and Storage Mount This mount is specifically designed for a Chinese dial indicator featuring a 9.5mm shaft. To ensure compatibility, the standard indicator back needs to be replaced with a flat back. I'm confident...

The need for hot-end wire management on the CR-10S Pro has never been more obvious than after installing Micro Swiss hot end, BL Touch and Klipper running on a Duet Mini 5+ with the ability to print ludicrously fast. ... The bracket needs to be...

This is my custom-designed fan duct for the Creality CR-10s. I am publishing it in order to assist fellow users who have encountered the same issue that I faced: the "twisted fan duct" consistently failed to deliver satisfactory results due to the...

In case you also want to print your feet out of TPU like I did, I recommend using more flexible glues which can be used with rubbers.Print SettingsPrinter: Creality CR-10SBrim: YesRafts: NoSupports: NoResolution: 0.2Infill: 15-20%Filament: Prusament...

A simple, yet more accurate re-creation of the X gantry calibration tool provided by Creality that ships with the CR-10S Pro V2. I measured Creality's version with calipers and it was 99.60mm. I assume it is supposed to be 100mm, so I created my...

Noctua NF-A4x20 Fan Mount and Shroud for Creality CR-10S Pro V2 Custom Cover to Conceal Noctua's Beige Fan Custom Fan Shroud Boosts Airflow on OEM Hotend...

This is My Version of E3D V6 All Metal Hotend Upgrade on My CR-10S. The Design Includes a Double Fan Setup and Utilizes the Precision Piezo Orion Module for Z-Axis Sensor. The New Design Is Silent and Prints Exceptionally Well. Printing High-Temp...

Remodelled official Bondtech BMG Creality CR-10S mount. The main problem with the standard mount is that it's hard to remove the piece of filament still in the bowden tube without a lot of fiddling around when the end of the filament passes the...

Remodelled official Bondtech BMG Creality CR-10S mount. The issue with the standard mount is that when the end of the filament passes the sensor, it is difficult to remove the piece of filament still in the bowden tube without a lot of messing...

Effective feet designed specifically for the CR-10S model can greatly reduce vibrations and significantly lower the noise level of the printer. These innovative feet are effortlessly clipped into place at the bottom profiles of the printer, making...

It basically does the same thing: It holds the tool set of the CR-10S Pro plus some extra tools and it wraps around one of the rubber legs, and also catches behind one of the screws that holds the bottom of the printer on. It stays there tight, but...

It essentially performs the same function: It securely holds the tool set of the CR-10S Pro along with some additional tools and wraps snugly around one of the rubber legs, also catching behind one of the screws that retains the bottom of the printer...

So I uploaded a v2, which should help dissipate heat better.* My version of a perfect Creality CR-10S Pro V2 Tool Holder. You will need 2x M5 25mm bolts with T-Nuts. Remove some screws from the printer's base and slide the holder's left 'fin'...

It securely bolts inside the body of a Creality CR-10S Pro and may also work with other printers. It attaches where the stock 4020 blower fan is typically located. The case becomes even more useful when paired with a fan mount like this one found on...

Just a simple cable support to organize the cables so they don't get damaged when upgrading CR-10 with direct drive system from Micro swiss. Works good. ... Mounted easly with some cable ties around the stepper motor and cables.

Might be useful for other situations too. Original description: This little yet cleverly designed piece, slips in the lower edge of the left vertical carriage to make it meet the end stop switch to bring a few millimeters extra of clearance. This...

This solves the problem some CR-10S and upgraded CR-10 have: when the Z axe slides the X beam downwards, the right carriage lower edge ends up resting against the second motor support just a tad before the left carriage lower edge triggers the Z end...

https://youtu.be/TMVGrmwluwY I designed this piece to hold a PTFE tube as a reverse bowden filament guide for my Creality CR-10S Pro V2. I have a filament dryer next to the machine and want to have the PTFE guide the filament out of the dryer and...

I've been using my custom-made fang style fan duct since the original one snapped after a few prints - decided to share it as there aren't many other models available that offer airflow from opposite sides on the stock CR-10S Pro configuration, which...

SummaryThis design is a remix of TallNHairyDave's magnetic base for the CR-10S Pro of Hamkers' camera arm.I love the design, but I had two problems:1) I could not source the same size magnets from Amazon used in the original. So instead, I switched...

I'm using my CR-10 S4 3D printer, which has upgraded steppers on the Y-axis, just like the ones found in the S5 model. ...Since none of the custom bracket designs online seemed to fit my needs, I decided to create a basic one myself using Blender.

This is a little experiment to drive the Z axis of a CR-10S with belts instead of lead screws. The gantry doesn't fall when you power down the printer. **Is it an upgrade?** It works well for me, but consider this an experimentation rather than an...

I made a quick redesign that you can use with standard bolts and nuts from the original CR-10S. I've noticed on my printer that the X-axis belt was rubbing against the frame due to misaligned belt positioning, so this part centers it perfectly and...

I designed a quick re-make using standard bolts and nuts from my original CR-10S model. I noticed that the X-axis belt was rubbing against the frame due to misaligned positioning, so I centered it with this new part and added an angle slot for the...

I'm reworking TallNHairyDave's magnetic base for the CR-10S Pro of hamkers' camera arm, giving it a fresh spin. I love the original design, but I had two major issues: 1) The initial magnet size wasn't readily available on Amazon, so I swapped...

In other words, while it was optimized for my setup with stock hot end and Microswiss nozzle, it should work well with all CR-10S Pro units. Please do not print this in PLA. Even though there is good clearance between the duct and the heater...

This is a Raspberry pi mount for the CR-10s pro with optional camera mount. It is designed to be mounted on either side or on the back of your 3D-Printer.</p> <p>The mount is extremly easily mount/removable for optimal flexibility.</p> <p>These are...