creality cr 10s pro z axis adjustment 3d models

Realizing that the Elegoo Mars features only a fixed holder for the light barrier on the Z-axis prompted me to design an adjustable construction of my own. Following production and assembly of the unit displayed here, I successfully adjusted the...

In the K8200 assembly manual, it states that the Z-axis endstop screw is initially installed upside down, with the head situated on the switch when the axis is homed. However, I found this arrangement inconvenient for adjustments. ...To rectify this...

Operators must calibrate Z-axis on compromised DaVinci systems featuring aftermarket Z-axis limit switches.

With the E3D volcano installed on the CR-10S, simply raise the Z axis limit. ...The attachment piece clips seamlessly onto the CR-10 cross piece above the Z axis switch; when in place, it triggers about 6mm earlier to prevent the volcano hot end from...

This is a precision replacement Z stepper motor bracket engineered specifically for the Creality CR10. It enables effortless adjustment, ensuring optimal alignment with the lead screw, surpassing the limitations of the standard stock bracket. The...

This is a direct replacement for the CR-10S Z Endstop Mount.

I printed the original design I liked but probably at too low an infill setting and between the long center section and the infill, it cracked so I shortened the shaft part and increased the infill to 100%. It works great and is incredibly strong.

After I noticed that the Elegoo Mars has only a fixed holder for the light barrier for the Z-axis I decided to create my own adjustable construction. After the production and the assembly of the unit shown here I could adjust the Z-axis exactly. Then...

I recently upgraded my Tornado 3D printer by installing the CR10 dual Z-axis, along with two high-quality GT2 20-tooth pulleys and a sturdy 720mm GT2 belt. ...Since the CR10 lead screw was longer than required, I designed and manufactured this custom...

Fan replacement for motherboard CR-10S Pro

My first publication. My first print with the Elegoo Mars showed me that I had a deviation of 1.6mm at the calibration cube in the Z-axis. After I noticed that the Elegoo Mars has only a fixed holder for the light barrier for the Z-axis I decided to...

The Creality CR-8 Z-axis stabilizer is specifically designed for use with the Creality CR-8 Z-axis. To install it, simply insert two screws into and then out of the Z-axis tower before adding the stabilizer. ...For added stability, consider placing...

Porta attrezzi per Creality 10S Pro, stampato il PLA Lite

Creality's Premium Linkage System for the CR-10S PRO - Upgrade Your Printer's Connectivity and Durability

This is a replacement fan duct designed specifically for the CR10S-Pro 3D printer. The source project can be viewed at https://cad.onshape.com/documents/9526b4e542a64217ae81de98/w/35ceba875888c9774892aad1/e/b9aad334de9abecdee01efcf. Version V1...

-A M4 T-slot nut -M3x20 Hex Flat Head Cap Screw (for the knob) The design I printed used the hex cap end of the screw with disc to adjust the Z axis height, but I noticed that I sometimes bump the damn thing throwing off my adjustment. So I designed...

This is a BLTouch support designed specifically for the CR10S-Pro.\r\nThe source project can be viewed here: https://cad.onshape.com/documents/852b2082d26b46d7f1c838e4/w/2fd458a37675a5a6d1da9383/e/30ef6a781b89d771db2ad864.

After creating a custom compact Z axis adjustment, I upgraded Marlin and began utilizing Mesh Bed Leveling. MBL allows for height adjustments above or below Z MIN, which made me concerned about triggering the end stop limit switch beyond its limit. A...

This bushing enables seamless integration of the CR-10 X-Axis Tensioner model (https://www.thingiverse.com/thing:2233139) with the CR-10S X-Axis idler pulley. ...To make this work, you'll need to swap out the existing M8x25 bolt and nut for a M5x25 bolt...

This bushing allows CR-10 X-Axis Tensioner (https://www.thingiverse.com/thing:2233139) model to work with a CR-10S X-Axis idler pulley. ...You will need to replace the existing M8x25 bolt and nut with a M5x25 bolt and M5 nut.</p> Category: 3D Printer...

This bushing enables seamless integration of the CR-10 X-Axis Tensioner model with a CR-10S X-Axis idler pulley. ...To make this work, you must swap out the existing M8x25 bolt and nut for a M5x25 bolt and a matching M5 nut.

This bed calibration test has been tailored for the Creality CR-10S PRO, which measures 300 by 300 millimeters in size.

A LED Ring Holder for the Creality CR-10 / CR-10S. I purchased an 80mm LED ring on eBay. ... https://www.ebay.com/itm/1-Pair-80mm-1210-3528-24LED-Auto-Face-Light-Halo-Ring-Light/282780486760?hash=item41d707cc68:g:iQ8AAOSwSutaO1nK The Diffuser...

After trying out various extruder covers designed by others and discovering they were too small for the new generation of CR-10 Mini extruders - the same ones found on newer CR-10S models - I decided it was time to design my own version. Going into...

#ZKNOB This two-piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw. It lets you manually control the hot end up and down when steppers are disabled, which I have found to be very handy at times. For...

**#ZKNOB** This two-piece part replaces and adds to the acrylic stock cover on the Creality CR-10's Z-axis lead screw; it lets you manually control the hot end up and down (when steppers are disabled), which I have found to be VERY handy at times. I...

This is a upgrade for the Creality CR-10S, and its variants that have Filament Sensor. My Sensor's internal limit switch arm broke, and I kept getting false stoppages, so I changed it to a more reliable roller-arm limit switch. I designed it to use...

Introducing an improved screw holder that offers enhanced support for the adjustment screw compared to the previous one. This new design is essential when replacing the second nut and the toothed washer with a small spring, which can be obtained from...

Improvements: * Avoids touching the wire of the Z stopper (see picture) * Does not touch the Z axis support (see picture) * Allows use with frame hoses (see picture) * No need to remove them (see picture) Simply place on the bars, sitting each tower...

I had been thinking about doing Z-axis reinforcements for my Creality CR-10S printer for a while, but I couldn't find anything that would work for my hotend group. The problem was the height, which I could have missed because the changes made have...