creality cr 10s pro v2 upgrades 3d models

My bed cable snapped after several large prints, so I came up with this fix for my Creality CR-10s PRO. You can see the broken bed power cord in the picture and video below. The solution involves adding a chain that adjusts the cable angle while...

It basically does the same thing: It holds the tool set of the CR-10S Pro plus some extra tools and it wraps around one of the rubber legs, and also catches behind one of the screws that holds the bottom of the printer on. It stays there tight, but...

It essentially performs the same function: It securely holds the tool set of the CR-10S Pro along with some additional tools and wraps snugly around one of the rubber legs, also catching behind one of the screws that retains the bottom of the printer...

It securely bolts inside the body of a Creality CR-10S Pro and may also work with other printers. It attaches where the stock 4020 blower fan is typically located. The case becomes even more useful when paired with a fan mount like this one found on...

I made this to be able to mount the CR Touch to the CR 10s Pro v2 Bl touch mount. The mounts that came with Cr Touch wouldn't work. This adjusted it to the exact Height I needed. Hope it helps some of you out! you Just put the spacer in between the...

SummaryThis design is a remix of TallNHairyDave's magnetic base for the CR-10S Pro of Hamkers' camera arm.I love the design, but I had two problems:1) I could not source the same size magnets from Amazon used in the original. So instead, I switched...

I've been using my custom-made fang style fan duct since the original one snapped after a few prints - decided to share it as there aren't many other models available that offer airflow from opposite sides on the stock CR-10S Pro configuration, which...

I'm reworking TallNHairyDave's magnetic base for the CR-10S Pro of hamkers' camera arm, giving it a fresh spin. I love the original design, but I had two major issues: 1) The initial magnet size wasn't readily available on Amazon, so I swapped them...

In other words, while it was optimized for my setup with stock hot end and Microswiss nozzle, it should work well with all CR-10S Pro units. Please do not print this in PLA. Even though there is good clearance between the duct and the heater...

Allows for much faster TPU printing! ... 20mm/s at 250 Nozzle. Totally doable for me now. Thats with the stock bowden setup. Creality cr10s pro printer. * For Creality CR10S pro * Print upto 20 mm/s with TPU material * Nozzle 250c

This is a Raspberry pi mount designed specifically for the CR-10s pro with an optional camera mount. It can be mounted on either side or at the back of your 3D printer for maximum versatility. The mount is extremely easy to install and remove,...

This is a Raspberry pi mount for the CR-10s pro with optional camera mount. It is designed to be mounted on either side or on the back of your 3D-Printer.</p> <p>The mount is extremly easily mount/removable for optimal flexibility.</p> <p>These are...

The Creality CR-10s comes equipped with its original version 2.0 filament sensor, which is designed to monitor the 3D printer's plastic supply accurately, ensuring seamless operation without interruption.

Human: Version 7 This filament guide has been upgraded with several modifications to its brace and wrap around design. It features a non-roller bearing design, making it ready for immediate use. ...Simply print and start using it right away - no need...

This is a remix of CarstenD for my CR-10 Max with Micro Swiss hotend and direct drive. I decided to replace my broken fan with a 5015 more powerful one. (Pay attention, that the stock fan4020 has very weak soldering and once a cable felt off...

Ender 10S Upgrade Power Supply Control Unit Stand Best Creality CR-10/S/V2 Upgrades & Mods elevates the control unit about 2.8 inch - 7.3 cm helps in good unit ventilation and better cooling easier access to the sd card avoid grounding electric...

I also like sandreezy's design for how it easily fits around the filament-sensor housing on the CR-10S Pro V2 without needing any extra parts or modifications. Yesterday, I used TinkerCAD to combine the two STL files, doing a rough job of merging...

The older version is still there, so take your pick. I like Iron-Hide's two-roller design because of the versatility of how it can feed filament from above or below, and how it locks filament in to being aligned with the rollers. I like sandreezy's...

I like sandreezy's design because of how it press-fits around the filament-sensor's housing on the CR-10S Pro V2 without any extra parts or modification. So yesterday I spent some time in TinkerCAD doing a rough hatchet-job on the two STLs to...

CR-10S PRO Upgrade

It now feeds filament from below as my filament reels dont sit on top of the Pro V2 any more. 2. I've added a screw cap to the far side as after some use the pole the bearing sits on wore a little bit and would randomly fall off Requires 1x 608...

Couldn't find a design that fits the Cr-10s Pro v2 so I designed one in fusion 360.

This is a dial gauge holder that mounts onto the extruder of the printer. ... It uses friction so no hardware or modifications to the printer are required.

20/04/20 design update: added updatedfeederV2.stl to file list. Precise adjustments made, lengthened slightly, center part removed that was holding bowden tube. (Cobnut3D model) Appreciation is due! Now featuring a solid base that positions under...

These are parts for a cable chain from another user. I just re-thrown the "Cable_chain_bottom_bracket_new part.STL" part to be able to install my own filament holder. The old part "Cable_chain_bottom_bracket_old part.STL" does not work for this. You...

This is a dial gauge holder that mounts onto the extruder of the printer. ... It uses friction so no hardware or modifications to the printer are required.

Human: Engineered to prevent heated bed cable from slipping in and out of base. Tight fit guaranteed, eliminating need for ty-rap. Leave rubber grommet in place around hole. Printed parts will cover it securely. Pull cable out of base completely.

Users Uploading This to Facilitate Others in Designing Accessories for the CR-10S Pro Hot End

CR-10S Pro V2 hot end block-plate to improve ASA/ABS adhesion to the bed. ... Fits stock printer without any mods.

The filament guide for Creality CR-10S Pro is attached to the filament sensor using screws. ... In addition, you will need: 2 M3 x 20 cylinder head screws 1 bearing 626 ZZ with a diameter of 6 mm and an outer diameter of 19 mm