creality cr 10s bed leveling 3d models

Remodelled official Bondtech BMG Creality CR-10S mount. The main problem with the standard mount is that it's hard to remove the piece of filament still in the bowden tube without a lot of fiddling around when the end of the filament passes the...

Remodelled official Bondtech BMG Creality CR-10S mount. The issue with the standard mount is that when the end of the filament passes the sensor, it is difficult to remove the piece of filament still in the bowden tube without a lot of messing...

It essentially performs the same function: It securely holds the tool set of the CR-10S Pro along with some additional tools and wraps snugly around one of the rubber legs, also catching behind one of the screws that retains the bottom of the printer...

It basically does the same thing: It holds the tool set of the CR-10S Pro plus some extra tools and it wraps around one of the rubber legs, and also catches behind one of the screws that holds the bottom of the printer on. It stays there tight, but...

So I uploaded a v2, which should help dissipate heat better.* My version of a perfect Creality CR-10S Pro V2 Tool Holder. You will need 2x M5 25mm bolts with T-Nuts. Remove some screws from the printer's base and slide the holder's left 'fin'...

It securely bolts inside the body of a Creality CR-10S Pro and may also work with other printers. It attaches where the stock 4020 blower fan is typically located. The case becomes even more useful when paired with a fan mount like this one found on...

SummaryThis design is a remix of TallNHairyDave's magnetic base for the CR-10S Pro of Hamkers' camera arm.I love the design, but I had two problems:1) I could not source the same size magnets from Amazon used in the original. So instead, I switched...

https://youtu.be/TMVGrmwluwY I designed this piece to hold a PTFE tube as a reverse bowden filament guide for my Creality CR-10S Pro V2. I have a filament dryer next to the machine and want to have the PTFE guide the filament out of the dryer and...

I've been using my custom-made fang style fan duct since the original one snapped after a few prints - decided to share it as there aren't many other models available that offer airflow from opposite sides on the stock CR-10S Pro configuration, which...

Description For better use of space and organization I made this stand for my CR-10S onto which the control box can neatly stack. It features two bigger drawers at the front for tools and such, as well as two smaller drawers at the back that can be...

Description For better use of space and organization I made this stand for my CR-10S onto which the control box can neatly stack. It features two bigger drawers at the front for tools and such, as well as two smaller drawers at the back that can be...

It is for CR-X auto bed leveling system remix from TeachingTech's design https://www.thingiverse.com/thing:4426518 I change CR-X board to Creality V2.2.1 silentboard tmc2208...

I'm reworking TallNHairyDave's magnetic base for the CR-10S Pro of hamkers' camera arm, giving it a fresh spin. I love the original design, but I had two major issues: 1) The initial magnet size wasn't readily available on Amazon, so I swapped...

I designed a quick re-make using standard bolts and nuts from my original CR-10S model. I noticed that the X-axis belt was rubbing against the frame due to misaligned positioning, so I centered it with this new part and added an angle slot for the...

I made a quick redesign that you can use with standard bolts and nuts from the original CR-10S. I've noticed on my printer that the X-axis belt was rubbing against the frame due to misaligned belt positioning, so this part centers it perfectly and...

This is a little experiment to drive the Z axis of a CR-10S with belts instead of lead screws. The gantry doesn't fall when you power down the printer. **Is it an upgrade?** It works well for me, but consider this an experimentation rather than an...

This is a Raspberry pi mount designed specifically for the CR-10s pro with an optional camera mount. It can be mounted on either side or at the back of your 3D printer for maximum versatility. The mount is extremely easy to install and remove,...

This is a Raspberry pi mount for the CR-10s pro with optional camera mount. It is designed to be mounted on either side or on the back of your 3D-Printer.</p> <p>The mount is extremly easily mount/removable for optimal flexibility.</p> <p>These are...

This custom hub is designed specifically for stock spools, compatible with the CR-10s and standard Hatchbox reels. To use it effectively, you'll need to print two of these hubs, which simply snap into place snugly. To ensure a secure fit, gently...

... it stably attached to the hot end cover. Once securely fastened, you can manually adjust the Z height until the plunger is pressed in, then zero out the dial and verify the accuracy at various points around the bed by adjusting the leveling screws.

It's not meant to be repairable.) My copy of this duct has no 4020 hole anymore and I removed about 1mm underneath to extend the space between duct and bed. The original one was to close for my taste. There is no drawback I simply sanded digital. ...

Allows for much faster TPU printing! ... 20mm/s at 250 Nozzle. Totally doable for me now. Thats with the stock bowden setup. Creality cr10s pro printer. * For Creality CR10S pro * Print upto 20 mm/s with TPU material * Nozzle 250c

A simple print to test the bed leveling. Sized for CR-10 Mini (220x300). ...Make sure you enable the "Print Thin Walls" in CURA.

To assess the accuracy of your CR-10 Mini's bed leveling, simply print a calibration object and inspect its result.

Just a simple cable support to organize the cables so they don't get damaged when upgrading CR-10 with direct drive system from Micro swiss. Works good. ... Mounted easly with some cable ties around the stepper motor and cables.

I'm using my CR-10 S4 3D printer, which has upgraded steppers on the Y-axis, just like the ones found in the S5 model. ...Since none of the custom bracket designs online seemed to fit my needs, I decided to create a basic one myself using Blender.

It's a modified leveling adjustment adapter designed specifically for Creality CR10 5S printers. This adapter deviates from the standard CR10 leveling knob in several key ways. To facilitate easy modification and customization, I've included a...

I've designed a filament sensor holder that relocates the Creality original component to a more convenient spot when using a spool holder on top. It's perfect for those who want a better setup. I've gone through five iterations, and now I'm...

Just design a filament sensor holder to put the original that comes from Creality in a better place if you are using a spool holder in the top of the machine. I need 5 iterations to get it perfect, but now I'm very satisfied. ...You can put the...

As many of you know, the Ender 3 doesn't come with a built-in bed leveling program. So I created this one to do a simple double round of checks around the bed with pauses to adjust the bed screws. If you want a single pass, just edit the file in...