creality cr 10 y axis pulley 3d models

This is a simple x-axis belt tensioner, utilizing a basic cam design mounted to the x extrusion via an extra m4 t-nut and one of the additional m4 screws provided with the cr-10. This setup significantly eases the process of tightening the x-axis...

3D printed parts for use with the plate listed here: https://www.etsy.com/listing/916768217/3d-printer-y-carriage-curtisy-plate Plate can be used with dual linear rails and mgn12h carriages or dual 2020 extrusion using the stock wheels from the Y and...

The main goal is to take off the wheels from the Y axis and swap them with two MGN12 rails. The rails are 500mm long MGN12. Two copies of each piece need to be printed. No need to touch the belt or motor. Just fix the two rails on the supports...

This is my fine Z-axis endstop adjustment that allows for a precise adjustment of the height of your Z-axis on the CR-10. BOM: 1x M4 x 5 brass threaded insert 1x M4 x 20 1x M4 hex nut 1x M4 locknut Use a soldering iron to press the threaded insert...

... many others were facing the same problem, making this extension a valuable addition to the community. To assemble and use this extension effectively, one must employ two pulley setups, as demonstrated through photos included in the make.

The y-axis belt of my CR-10 was torn apart due to damage from the initial endcap. I obtained a replacement belt and created an alternative endcap that would not harm it. It's essential to note that the new belt must be longer than the original one,...

T8 600mm 3D Printer Stainless Steel Lead Screw Coupling Shaft Mounting Bearing Link: http://r.ebay.com/eVLz50 BIQU GT2 Synchronous Wheel 60 Teeth 8mm Bore Aluminum Timing Pulley for 3D Printer 6mm Width Belt (Pack of 2pcs) BIQU Link:...

The CR-10 linear rail mounts are designed for the X-axis and specifically fit the NSK LS150530CLD2K02PN1 model. ...These mounts require the SK-004 saddles, which feature part number 3x-004 for optimal performance and compatibility.

X-axis cable support for the CR-10 S5 3D printer is a must-have feature, as it prevents the PTFE tube and X axis electronics cable from colliding with the bed at low Z-axis heights. ... To install this essential component, you will need to replace two...

These new components are created to utilize 4 six-thirty-second screws, 6 nuts, and the bearings from each standard belt pulley/tensioner assembly. No additional hardware is required. If you have any questions about the parts or experience issues...

... the parallelism and adjust to the aluminum rail profile without any play. ...Don't hesitate to use a file for optimal results. The diameter 4 axis of the cap is locked in place and directly in contact with the screw heads for precise adjustment.

Release the Y belt tension 2. Loosen motor bolts that secure it to the frame 3. Remove the rear motor mounting bolts 4. Attach the bracket to the frame using the M4 bolt and T nut, but do not tighten yet 5. Secure the bracket to the motor with four...

This upgraded component is specifically tailored to enhance the capabilities of the Creality CR-10 3D FDM Printer. The bar collectors in question are engineered to accommodate tubes with a diameter of either 10 millimeters or 19-20 millimeters. ...If...

I designed an alternative Y-motor bracket since the ones I found wouldn't fit my CR10 S5 printer. The original brackets' screw recess holes were too small, but they still work for me so I'm not planning any modifications. To attach the new bracket...

This design is an upgraded version of a Y belt Tensioner from several years ago, boasting improved performance and stability thanks to its robust mount. Any print involving screw threads requires thorough testing, ideally with at least one test...

All for a CR-10 Mini but just increase screw lengths for CR-10. I used a new 500mm screw (T8*8) but re-using the original I needed to add a bit to get full travel, see TXT file. May be worth buying 2 new screws to save messing about. My basic...

If you don't plan on upgrading your CR-10 with an X axis tensioner but still want to enhance that side of your printer, then this is for you! It doesn't obstruct the belt or the extruder and looks nice if you dislike the bare metal look of your...

If you're dealing with a defective plastic X-axis cover on your CR-10(S), don't worry, we've got you covered! Below, you'll find a comparison between the damaged part and its replacement. ... The original component is depicted in black, while the...

This is an x-axis led stripe holder designed specifically for the cr-10. I drew inspiration from thx's cable management clips found on Thingiverse (https://www.thingiverse.com/thing:2539274) and incorporated a rotateable led stripe holder, ensuring...

UPDATE 02/06/2019 SIGNIFICANT UPDATE X TENSIONER FOR CR-10 / CR-10S Mk7 VERSION The guide system has been upgraded and simplified, applying changes to all models. The dimensions of the screws have been unified across all versions. The minimum belt...

This is an X axis height adjustment tool designed for the CR-10, especially if the Z axis upgrade is installed. ...Nevertheless, it can be certainly used for other 3D printers.You need to print two tools to use it.Move the extruder in the middle on the...

This is a versatile x-axis height adjustment tool engineered for the CR-10, particularly when paired with a Z axis upgrade. However, it can also be utilized effectively on other 3D printers. To use this tool, you'll need to print two identical...

This is a custom-designed cover for the x-axis motor on the CR-10, featuring a clip at the back that securely holds it in place.\r\n\r\nThe cover I printed includes my personal logo, but you can modify it to fit your needs by utilizing the provided...

X-Y Axis Calibrator (10-150mm)

Update of February 6th, 2019 MAJOR UPDATE X Tensioner for CR-10 / CR-10S Mk7 Version Upgraded the guide system and simplified all models Unified screw dimensions (with other tensioner versions) Modified minimum belt tensioning position (for short...

This is a LED strip holder that latches in the X axis extrusion slot of a CR-10 3D printer. You attach a LED strip to the bottom to light up the bed while printing an object.This is a remix of http://www.thingiverse.com/thing:2252158. I removed the...

The x-axis belt of my CR-10 was severely torn apart because it had been compromised by the original endcap's flawed design. I promptly acquired a replacement belt and created an entirely new endcap that would not compromise the integrity of the belt....

This design interfaces only to my CR-10 v3 Filament Sensor Relocation Bracket: [https://www.thingiverse.com/thing:4716470](https://www.thingiverse.com/thing:4716470) This isn't a remix of __Biffo318__'s design, but its positioning and configuration...

The lower bracket fixing is taller than the original remixed file to allow standard 750mm M10 threaded bars to be used, commonly available from sellers like this:...

This adapter enables seamless integration of the original CR-10 carriage into a custom-built setup featuring the robust MGN12H system, while retaining all the original hardware components.