creality cr 10 y axis pulley 3d models

To build this mount, you'll need: 3 M5 x 12 mm screws 2 M5 t-nuts - You should already have one from your old mount and a couple of extras came with the CR-10 (at least that's what happened in my case). ... You can modify this design using Tinkercad...

I haven't spotted any rear y-axis pulley covers for the CR-10, so I whipped one up in Fusion 360. The part clips over the center section of the stepper motor from above. If it needs adjusting, let me know; revisions are being made, so keep an eye on...

If you swap out the smooth idler pulley on the Y-axis of the Creality printers for a toothed GT2 pulley, you'll notice that the new pulley is significantly narrower.\r\n\r\nThese spacers are designed to replace the stock white plastic spacers either...

My original y axis belt tensioner started to show some cracks i got proactive and made a replacement because i couldn't find a replacement on websites It's recommended to make this with the toughest filament you have or make from aluminum plate with...

Mount for rail MFN12 on Creality CR-10

Y axis belt tensioner for Creality Cr-10 S4 & S5 only. 3 main piece all self locking, sturdy and hand adjustable. Reuses standard parts, No bolts to buy. This unit greatly reduces shock, jerking and noise of printer especially at high speeds and acts...

This part is to replace the original in case of breakage. ... This smaples was printed on Creality CR-10 Smart

Assemble the MFN12 mount specifically designed for the Creality CR-10 rail system. The mounting process is straightforward and requires careful attention to detail. Begin by aligning the rail guides of the MFN12 with the corresponding slots on the...

New Combo YZ Bracket for Enhanced Print Quality When integrating this combo with Thingiverse's design, https://www.thingiverse.com/thing:2757810, you'll experience a significant reduction in Y-axis bed cabling issues. To eliminate the nuisance of...

Pressure fit cover for Y Axis belt/idler. ...To install, slide on from the rear to the front of the Y axis idler bracket.

This is the plastic component that secures the stop switch to the y-axis.

One of the bearings in the pulley assembly of the y-axis belt broke. The bearings proved too difficult for me to remove without damaging the pulley. Needing an out-of-warranty replacement (search on Amazon B07QFL7VS4), shipping times were long. While...

I needed a slight adjustment to the Z Axis motor mount after installing the "Creality CR-10 Wire management, Strain relief and Glass holder" from Thingiverse's 2328449, which interfered with the corner of the motor mount, restricting Y Axis travel...

This is a slight adjustment to the Z Axis motor mount I needed after installing the "Creality CR-10 Wire management, Strain relief and Glass holder" https://www.thingiverse.com/thing:2328449 which I found impacted the corner of the motoer mount,...

To print the complete chain for y axis on your CR-10 mini, you need: - 6x Top (https://www.thingiverse.com/thing:2708420) - 6x Bottom (https://www.thingiverse.com/thing:2708420) - 1x side_bracket (https://www.thingiverse.com/thing:2708420) - 1x...

I had this to mount my Y axis stepper https://www.youtube.com/watch?v=fKDs7HW3cAE

I got tired of using a smaller GT2 idler pulley that I had replaced my stock Creality idler bearings with for smoother prints. I had used a smaller bolt and it had started bending in towards the printer and so wasn't as tight as it used to be. This...

What you will gain is much improved Y axis performance at the cost of a little noise due to the fact there's no more belt to dampen the motor. On my S5 I had constant issues with skipped steps and this has solved that. #BOM: These links are...

This one is designed specifically for the larger CR-10 S5 and S4 series machines, utilizing easily available parts that are easy to print. This upgrade is inspired by the [3DLS Complete Belt-Free 3D...

May I put some more information in my blog, try to have a look, may it's published already: German: https://www.moralin.net/de/blog English: https://www.moralin.net/en/blog for X axis, you need * 16 (2x8) cable chain elements *...

after downloading over 100 links and all the mounts for 3 of my cr-10s. I was searching all over for bolts. Then thought , "Does my ender need chain and mount bolts?" .....rhetorical No bolt option Also simplifying the top bracket to just...

https://www.youtube.com/watch?v=fKDs7HW3cAE Liner Rails I Used...

https://www.youtube.com/watch?v=fKDs7HW3cAE Liner Rails I Used...

I've revised the Y plate cable fixation to add the cover intended for the base piece, but this time tailored to secure the chain attachment. ... Printing: * 8 bottom links (100% infill) * 8 top links (100% infill) * 1 side bracket (20% infill) * 1 bed...

I've created yet another CR-10 belt tensioner. In this instance, I aimed to preserve the appearance of the printer while incorporating a tensioner. ... I'm counting on all of you to appreciate this design, so please share any suggestions for...

I'm going to install a damper on the back of the Y motor so it stays perfectly aligned.\r\n\r\nThe part fits like a glove and lines up perfectly with the step motor.\r\n\r\nTo get this part working in sync with the damper, I used two new M3x40mm...

Creality CR-10 Smart X-Axis Covers. Attach with glue or with some thin double sided tape. They are actually covers for your existing covers. You need to pull a lot apart to get the original ones off. These make it easier than replacing the whole...

A Sleek Cover Design for the Front Y-Axis Wheel of the Creality CR-10 and CR-10S 3D Printers, Perfectly Matching Their Industrial Chic Aesthetic.

update 2018 05 08: added V2.1 with longer filament tube holder 08.05.2018 Version 2.1 mit längerem Filamentschlauchhalter hinzugefügt I gradet my Creality CR-10 to a CR-10S 300 up and used the opportunity to manage the cables new. I didn't like the...

I just upgraded my Creality CR-10 to a CR-10S 300 and had the chance to organize my cables again. I wasn't happy with the filament tube movement and hotend cable arrangement, so I designed holders for the end stop holder and hotend attachment. For...