creality cr 10 fan upgrade 3d models

... ...Requires flashing the firmware. Uses stock screw hole on left side after removing the fan housing and allows for height adjustment to get to just the right spot. Connect VCC to 5V, GND to Z end stop ground pin and OUT to the other Z end stop pin.

Next, connect all necessary cables, including power leads, fan connections, and any additional control wires, making sure they are properly secured to prevent damage or obstruction. ...Finally, test the system thoroughly to verify that the PSU is...

This is a high-performance fan duct for the Creality CR-8 3D printer. No supports are required. It's recommended to print with ABS material. Copper tape provides insulation, protecting the main body from radiation heat. The fan protection cover adds...

###Chimera Dual Extruder mount/cooling system 50mm fan version for Tevo Tornado/Creality CR-10/Ender-3 It's a base module that combines a mount and cooling system specifically designed for the e3d chimera dual extruder, compatible with Tevo Tornado,...

Fine Tunning this excellent extruder upgrade from user @Jsphtg for Creality CR-10S Pro V2. I tweaked a little bit more the feed filament hole to fit at diameter 2,1mm which i found perfect match while using TPU/FLEX filament. Moreover you dont need...

The CR-3040 comes without a fan duct, making it suitable for ABS printing, yet unsuitable for PLA. ...This is my first attempt, and surprisingly, it works out well.

CR-10 Enclosure. Remove all 3 Internal fans, Including the Power Supplies fan. Remove top cover for optimal cooling. Found best option for mounting the MOSFET was to use mounting tape. Mounted Power Supply using Mounting tape. This is a test. So try...

My Printer: Creality CR-200B Creality Sonic Pad Phaetus Dragonfly BMS CR-Touch

A LED Ring Holder for the Creality CR-10 / CR-10S. I purchased an 80mm LED ring on eBay. ... https://www.ebay.com/itm/1-Pair-80mm-1210-3528-24LED-Auto-Face-Light-Halo-Ring-Light/282780486760?hash=item41d707cc68:g:iQ8AAOSwSutaO1nK The Diffuser...

I recently encountered a problem with my CR-10 circuit board fan, which failed after approximately two months of use. In order to resolve the issue, I disassembled the unit and replaced the faulty fan, but during this process, I was disappointed by...

Engineer modified a 12-millimeter sensor holder onto an upgraded fan system originally designed by Racusch.

This is a model I built to attach a 40mm fan to the stock CR-6 heat block. It fits perfectly in the stock fan enclosure and the grill on the front almost looks like it was designed for a larger fan. It loads upside down, so be sure to flip it...

Required materials: 0) CR-200B 1) Creality Spider hotend, aluminum heatsink option (not the high flow one) __Since the original hotend heatsink is only 12mm wide and the Spider has 16mm, 2mm are to be cut from one side to ensure concentricity with...

As I fell in love with SanderPuhs's Cr-10 Fang design and printed it for my customized CR-10, I had to acknowledge that one small thing wasn't functioning properly. Sander did an excellent job designing the BLTouch mount, but because of its...

Habe hier eine Abdeckung für den CR-6 Max gebastelt, für einen 92x92 Lüfter Gedruckt mit Stützstruktur PLA

The individual attaches a fan to a wall-mounted bracket on the wall.

You need the Noctua 60x25mm Fan and a Step-Down for 24 to 12v Just Plug in the Fan and mount it like before, you also can use more spacers on the Ground for more air vantilation

I remixed this remix for the CR-6 se. I ran it through Meshmixer and smoothed it out a bit. There was an odd hole that I filled in. Best printed in a higher temperature plastic than the plastic you plan on cooling. ... Close proximity to the nozzle...

...Replaced the fan mounting for 92mm fan. I used a noctua B9 but I think any 92x92x25 fan would fit. 3. Removed the internal ridges to make room for the fan. Still fairly rigid due to the increased rim. 4. Reduced bottom thickness from 1.5mm to 1mm.

After searching online and finding similar part cooling ducts for the CR-10S, I still encountered the same issue - the part would consistently rest against the heat-block. This design fully encloses the nozzle, making it more challenging to see and...

A highly adaptable, modular tool storage system designed specifically for Creality CR-10 or CR-10S control boxes. This comprehensive package includes two distinct base options, plus a variety of versatile holders and containers to suit your unique...

I was having trouble printing with some flexible filament right off the bat using my Creality CR-10S Pro, so I experimented with a few mods from here but none of them delivered the results I needed. To get something working, I combined elements from...

Four screws are required to secure the fan guard, utilizing the existing screw holes in my fans – specifically 4x M3x30 and 2 x M4x20 screws along with 2x M4 nuts. If anyone prints this design, I'd appreciate it if you could share pictures of your...

I've got a second Cr-10 with dual Z axes, and it seems that the nozzle is positioned about 1-2mm further back than usual for some reason. I printed this in PLA on my Maker Select Plus using 0.2mm layers, and the result was fantastic. I did use...

Extruder Crank for the Creality CR-10. ...Body Dimensions: Ø 35 mm x 8 mm External Top Dimensions: Ø 8 mm x 7 mm Internal Top Dimensions: Ø 5.2 mm x 12 mm Flat Area: 4.5mm

This is a simple filament guide, quick to print and easy to attach. I printed it PETG and combined it withthe spool holder i also designed for CR-10. Category: 3D Printer Accessories

This easy-to-print filament guide attaches quickly and securely to your printer. ...Printed in PETG, I paired it seamlessly with my spool holder design specifically crafted for the CR-10.

This fan duct works perfectly for me with dual Noctua 40x10mm fans, delivering very efficient cooling performance. I was a bit worried about the axial fan's ability to cool the hot end, but it actually worked really well. I personally prefer this...

I kept getting wisps of filament sucked into my hotend fan so I designed this duct to keep that from happening.

... inside my enclousure, so I made a 50mm fan mount with double the cfm. ... Design based on: https://www.thingiverse.com/thing:2160958 and https://www.thingiverse.com/thing:2784134 The cooling fan mount I use is: https://www.thingiverse.com/thing:2197329