creality cr 10 direct drive 3d models

This is a modified extruder arm/base with a cable holder integrated for direct drive conversions. This is mainly for the Speed Drive conversions: https://www.thingiverse.com/thing:3816051 I had my doubts as to how long this would last, but I printed...

Since I'm using a Micro Swiss direct drive extruder, I think I have more room between the X rail and part cooler, so it's possible to squeeze the bltouch in behind the cooling duct. These things are under the fans:...

I am no designer, engineer or expert designing parts for 3d printers, I just adjusted the original parts design by DaVinci2000 to make them work with the Creality CR-10 V3 using the stock parts it comes with. If you find this useful you can...

This is a remix of my other CR-10 FANG. For this one I adapted the monoblock mount for the mosquito and made it fit with the Phaetus Dragon hot end. I ended up having to redesign the mounting plate that also holds the BLtouch, had to drop the...

--Simplicity Easy Direct Drive Conversion-- I have included my custom direct drive mount that rotates in reverse direction from stock. China sent me the wrong alloy parts so I had to re-pin the connector at the board to run the stepper in reverse. I...

Remixed from Kopiemn direct drive to support a Bondtech BMG extruder (left hand version). This is configured to line up with hotends mounted in the Hero Me Gen5 cooling system. ...Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No Supports:...

Since the X Carriage of the CR-10 V2/V3 is very different from the standard Ender 3/CR-10 Carriage I designed this adapter for it. Thank you to to Adolf_Muffin for the original design (https://www.thingiverse.com/thing:4293887) and TwoPuncakes for...

... well. This part cooler duct was printed before switching to the Micro Swiss direct drive setup, resulting in some underextruded layers. ...However, tension issues with the extruder drive are now resolved thanks to the excellent Micro Swiss design.

# Introduction I upgraded my extruder and hot end on the CR-10 primarily to work with flexibles, but also because the original hotend and extruder were not that great. This mount attaches the Titan extruder and V6 hotend directly onto the X...

mount titan extruder and volcano on x axis of the cr-10

Since I'm using a Micro Swiss direct drive extruder, I think I have more room between the X rail and part cooler, so it's possible to squeeze the bltouch in behind the cooling duct. ... These things are under the fans:...

This is a remix of a fan housing I found on Thingiverse, and it worked well for my Ender 5 Plus, with a Microswiss direct drive and Mosquito hotend. ...I'm not going to maintain this post, but I thought I would share.I printed it in 25/75 carbon nylon,...

Support for neon lighting on Creality CR-10/CR-10S/mini or any machine with a 2020 or 2040 profile allows you to secure the LED neon lights available at Action stores. ...This results in minimal loss of print height.

I tried Sashalex007's SpeedDrive v1 direct drive conversion (https://www.thingiverse.com/thing:3816051), but the two pieces couldn't fit together. I originally just modified the two pieces to work together, but the combination wasn't seamless. So, I...

Note: If it's your first attempt at direct extrusion, you might want to decrease print speed and acceleration on the X-axis because there is more weight on the sleigh than before. Bugfix01: Mounts of 2ndFan too long -> chopped Update: There is...

Some direct drive mount are already existing, but it seems that all of them were using a printed part to mount the extruder and I didn't wanted to experience any vibrations in the extruder during retractions, so I bought this plate from aliexpress,...

Remixed from Kopiemn direct drive to support a Bondtech BMG extruder (right hand version). This is configured to line up with hotends mounted in the Hero Me Gen5 cooling system. Print Settings Printer Brand: Prusa Printer: I3 MK3S Rafts: No...

The direction of the fan is uncertain due to the Copperhead being slightly taller; time will tell if it is perfectly aimed. The BL-Touch mount has been reinforced and a center hole added for pin access. Shims are included to help achieve the desired...

After deleting the outdated files, I modified the direct drive after printing it, only to encounter issues that required cutting the wrap-around square to allow filament feeding. Do not attempt to print this yet. Upon further inspection, I realized...

This is a modified mount for the Voron Afterburner to mount it to a CR-10/Ender style printer using a single 400mm MGN12H linear rail. It is modified from the new Voron Switchwire printer that just came out. It uses the same design with a single...

This is a remix of Wundel's Ender 3 Direct Drive conversion kit, showcasing impressive promise, but unfortunately, two negative comments arose - one concerning the oversight of a spot to tie cables and another regarding tilting the 5015 fan at 45...

I use M3x4mm brass inserts, available at https://www.aliexpress.com/item/100PCS-OD-4-3-M3-3-4-5-6-8-10-12-brass-insert-nut-knurled/32793013316.html Update 08.03.2019: I added an EZABL 18mm Mount. Update 23.04.2019: I added a BLTouch mount, a nozzle...

Print Settings: Printer: Creality CR-10 Rafts: None Supports: None Resolution: 0.2mm Infill: 15% Notes: To ensure the parts print flat, rotate them accordingly. For a unique X-pattern design on the bottom tray, omit the top layer and use grid infill...

Stock Creality screws should work here. Tolerances are tight in order to ensure a secure fit, your printer will need to be well adjusted for success here. I would print in PETG (pictured) for best results, but this should work in PLA if your make...

The Creality CR-10 Extruder Carrier is accurately modeled within a +/- 0.15mm tolerance, based on a real-life CR-10. It features basic elements such as fans, fan housing, extruder, bracket, and alignment screws. The model was created using Fusion 360...

This is a modified version with a stronger part which clips to the metal plate and also an easier print on it's side with less supports needed.

Special thanks to original creator Greg191134 of "The Tank" Bondtech BMG + E3D v6 Print Head https://www.thingiverse.com/thing:3080548 The original model is truly exceptional and will suit most users perfectly. However, I wanted a design that didn't...

Remix of this https://www.thingiverse.com/thing:4543524 But thingiverse won't link to it. Adapted for a Titan extruder or clone. I liked this mount for my stock extruder as it was really solid so made one for the titan, so its now mirrored to have...

Special thanks to the original creator Greg191134 of "The Tank" Bondtech BMG + E3D v6 Print Head https://www.thingiverse.com/thing:3080548 The original model is a great design and will work perfectly for most people. I wanted something that didn't...

I had to remix this because the hole for the hotend didn't line up. I printed it in PETG with tree supports touching the bed in Cura 5.1 and it worked out great. ... Thanks to Kopiemn and mediaman for giving me something to work with.