creality 3d printer ender 3 v2

LCD Screen Frame for Creality Ender-4 3D Printer Print Settings: Layer Height 0.2 mm, Infill Density 20 Percent

Upgrades on my Ender3V2: My Printer : https://www.bastelgarage.ch/creality-ender-3-v2-220x220x250mm-3d-drucker Silicone dampers : https://www.bastelgarage.ch/silikon-dampfer-feder-set-fur-heizbett CR Touch Auto Leveling :...

Dial Gauge holder for the Ender-3 V2 printer. ... I recommend support under connection frames with cover.

Original design for Creality ender 3 3D printer

Original design for Creality ender 3 3D printer

This Mount make it possible to mount the Display of the Creality Ender 3 V2 directly on the side.The Slots for the Display are taken from this Model: https://www.thingiverse.com/thing:4744628The side to keep hold on any 40x40 extrusion is taken from...

Instead of purchasing another bed leveling probe/sensor, I decided to create a mount for it.This is a remix of the gantry from the Hero Me Gen6 Master Suite for mounting a BFPTouch to an Ender 3 V2 with the Creality Spider hotend.Hero Me 6 -...

Requires 2x M2.5 or M3 bolts at least 5 mm long. If your probes came with washers, those may not fit, just exclude them from installation. Install at 3mm above the nozzle initially, fine tune after installation complete (including firmware). For Gen...

I created the Lamborghini themed pack for Creality Ender 3 v2 it took a lot of work... ...the blower system is well oriented to have a better cooling efficiency.

Improved BLouch mount for Creality Ender 3 v2. Added special mount holes for M3 nuts. Added small cut in the right upper corner to avoid connection with screw. Enforced plate to avoid deformation by temperature. ... ABS is recommended for print.

I found that the spool holder that came with my Creality Ender 3 V2 had some slop in it. The hardware was bottoming out on the extrusion, so I designed a small shim to prevent this from happening. ...

although you do need to extend the wire. Added the Sketchup file for easy editing. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.16 Infill: 10% Filament: Real Filament Black Matt PLA Black ...

Just my design for the Ender 3 V2 Display Knob...

Works a treat. Takes about 56 minutes to on an E3V2 using stock Cura settings. If using new bolts, you will need - 4x M3x19mm Printed at 0.2mm with 15% infill and is plenty strong enough. Print Settings Printer Brand: Creality Printer: Ender 3...

----- CAD: FreeCAD 0.20 Printer: Creality Ender 3 V2 Rafts: No Supports: No Resolution & Nozzle: 0.2 mm & 0,4 mm Infill: 100% Filament brand & color: unknown ------------------------------------------------------------ Lammcou GoPro...

I modified my son's filament sensor mount to be able to mount the Creality filiment sensor on my Ender 3 V2. https://www.thingiverse.com/thing:4890156 His mount corrects alignment issues of other mounts for the Ender 3. ...His uses the repurposed Z...

I have designed a spool holder for the Creality ender 3 V2 printer. The design uses no ball bearings and fits into the stock spool holder. The main advantage of this design is that despite the fact that it does not use ball bearings, the unwinding is...

I have designed an entire replacement housing that incorporates all the features of this print as well as fixing the problem of the filament getting caught inside the housing:...

This Mount make it possible to mount the Display of the `Creality` `Ender` `3` `V2` directly on the side. ... The Slots for the Display are taken from this Model: https://www.thingiverse.com/thing:4744628 The side to keep hold on any 40x40...

My Creality Ender 3 v2 was squeaking loudly when pulling on the filament, so I made a low-friction filament holder. Requires a screw or bolt (6mm or 1/4in, ~100mm or 4in long) and two 608ZZ ball bearings. ...Will work with the printable nuts included...

Lets you mount a Raspberry Pi Camera module on the front of your Ender-3 v2.

Actualización: 01/04/2022 -Se baja la ventilación para una mejor refrigeración de las capas -Se Modifica altura soporte Cr Touch igual al "soporte original de Creality"...

Upgrade: 01/04/2022 -Se baja la ventilación para una mejor refrigeración de capas -Se Modifica altura soporte Cr Touch igual al "soporte original de Creality" Satsana para Ender 3 V2 Con Ventilación Original y Soporte para CR Touch Creality. Se hace...

I have designed an entire replacement housing that incorporates all the features of this print as well as fixing the problem of the filament getting caught inside the housing:...

Mount for 12 mm diameter static ABL probes (capacitive & inductive) for the Creality Ender 3 V2. Requires 2x M2.5 or M3 bolts at least 5 mm long. If your probes came with washers, those may not fit, just exclude them from installation. Install...

(see in the remix tab) Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.3 Infill: 20% Filament: Das Filament PETG transparent Notes: The part is, as mentioned, optimized for a 0.6mm nozzle for faster...

This is a known issue of Creality mainboards version 4.2.2 (see for example here: https://forums.creality3dofficial.com/community/ender-3-v2/layer-shift-ender-3-v2). So I decided to design this better case where air can flow around drivers and get...

This is a tool drawer replacement for Creality Ender 3 V2. It allows mounting of a Raspberry Pi 3B+ inside the Ender 3 Shell for use with OctoPrint. ** IMPORTANT ** This has not been tested for temperatures yet, or use with the printer inside an...

So that includes: - Creality Ender 3 - Creality Ender 3 Pro - Creality Ender 3 V2 - Creality CR-10 ### 3 SIZES There are 3 sizes to choose from: - **M** - Medium - **L** - Long - **XL** - Extra Long I personally use the **Long** version, which gives...

This is a remix of the gantry from the Hero Me Gen6 Master Suite for mounting a BFPTouch to an Ender 3 V2 with the Creality Spider hotend. Hero Me 6 - https://www.thingiverse.com/thing:3182917 BFPTouch - https://www.thingiverse.com/thing:2890290...