creality 10s pro 3d models

The need for hot-end wire management on the CR-10S Pro has never been more obvious than after installing Micro Swiss hot end, BL Touch and Klipper running on a Duet Mini 5+ with the ability to print ludicrously fast. ... The bracket needs to be...

SummaryThis design is a remix of TallNHairyDave's magnetic base for the CR-10S Pro of Hamkers' camera arm.I love the design, but I had two problems:1) I could not source the same size magnets from Amazon used in the original. So instead, I switched...

It essentially performs the same function: It securely holds the tool set of the CR-10S Pro along with some additional tools and wraps snugly around one of the rubber legs, also catching behind one of the screws that retains the bottom of the printer...

It basically does the same thing: It holds the tool set of the CR-10S Pro plus some extra tools and it wraps around one of the rubber legs, and also catches behind one of the screws that holds the bottom of the printer on. It stays there tight, but...

I've been using my custom-made fang style fan duct since the original one snapped after a few prints - decided to share it as there aren't many other models available that offer airflow from opposite sides on the stock CR-10S Pro configuration, which...

I'm reworking TallNHairyDave's magnetic base for the CR-10S Pro of hamkers' camera arm, giving it a fresh spin. I love the original design, but I had two major issues: 1) The initial magnet size wasn't readily available on Amazon, so I swapped them...

In other words, while it was optimized for my setup with stock hot end and Microswiss nozzle, it should work well with all CR-10S Pro units. Please do not print this in PLA. Even though there is good clearance between the duct and the heater...

This is a Raspberry pi mount designed specifically for the CR-10s pro with an optional camera mount. It can be mounted on either side or at the back of your 3D printer for maximum versatility. The mount is extremely easy to install and remove,...

This is a Raspberry pi mount for the CR-10s pro with optional camera mount. It is designed to be mounted on either side or on the back of your 3D-Printer.</p> <p>The mount is extremly easily mount/removable for optimal flexibility.</p> <p>These are...

I upgrade my CR10s Pro to direct drive using the following design https://www.thingiverse.com/thing:4809013 With this upgrade you loose the ability to run the filament through the factory filament sensor location. This design relocates the...

Two 10-millimeter diameter bearings with a flanged design are needed to fulfill this requirement.

I revamped this by inserting an additional component that nestles beneath the printer. This envelops one of the rubber feet, and also clamps behind one of the screws that secures the printer's lower casing in place. ... It remains firmly in position...

This part cooling fan mount is compatible with both the stock 4020 fan and a more efficient, easily accessible 5015 fan. I achieved the best possible results in my 3D Printer Test by combining this duct with a 5015 fan. ... To install a 5015 fan: * 2...

Simple protector to put in the rectangular hole (see picture), for BLTouch cable for example. ...Printed in TPU, didn't tried with solid material

I made this in Fusion 360 because I could not find any filament guide I liked. ...This has workped perfectly for me yet.

A simple tool holder for a trowel and inspection lamp or pliers.

I created this tool holder to learn Fusion 360 functionality. Initially, my plan was to modify an existing AnyCubic Mega tool holder design, but I couldn't successfully navigate the BRep process. I gave up and started from scratch because it provided...

Original design overlooked crucial component - door handle. ...Resourceful problem-solving led me to devise makeshift solution using Tinkercad, where I cleverly joined pre-existing hinge parts to achieve functional outcome.

A simple 20x40 spool holder requires a sturdy 8mm axle to maintain stability and keep your spools organized.

This is a big-wheel filament feeder to guide the filament in cleanly. Parts required: one M6x30 bolt or a printed axle one 17x6x6 bearing This part is retained under the filament switch itself and clamped by the original 4 screws. There...

Originally printed and used this design for a couple days: https://www.thingiverse.com/thing:3624094 I had trouble getting the two bigger allen keys into place so I increased the sizes by a little bit. ...I also added another spot for a wrench as...

Place a simple shield in the rectangular opening (refer to the image) to safeguard the BLTouch cable. ...This protective cover is designed to be printed with flexible TPU, although it may also work with rigid materials.

Because in the version from https://www.thingiverse.com/thing:3681040 the part fell out recently, I have adjusted the design slightly. ...The part for the bearing and the pin has remained from the original, but the clip is now used from...

This part cooling fan mount can be used with the stock 4020 fan as well as a more efficient (and more accessible) 5015 fan. With this duct and a 5015 fan I printed the absolute best 3D Printer Test I've ever printed. ... For 5015 fan: 2 x M3/25 2 x...

This is a remix of https://www.thingiverse.com/thing:4398918 This design provides additional hooks to make the design more steady and reduce flex while printing. ... The material used here is PETG

This part bolts on to the top of a rod on the Z-axis Print 3 bearing casings Print 3 bearing pins Print 1 filament guide

When printing from https://www.thingiverse.com/thing:3681040 the clip failed to work for me, so I made some adjustments to make it printable separately and a bit more stable. ... The print was rotated 90 degrees as shown in the attached photo.

Used CURA settings include tree support and a quality setting of Dynamic. The fan utilized is a Noctua 60 mm model, powered by a 12-volt source. To adapt the fan's voltage requirements, a buck converter was employed to convert the input voltage...

I created this filament holder with ballbearings to make the filament spool spin more smoothly, preventing breaks and tangles. This design works well in conjunction with the original steel racket that comes with the printer, replacing the standard...

Dial Gauge Holder for Creality CR-10S Pro V2 vertical mount with screw and nut This is a dial gauge holder that mounts onto the extruder of the printer. It uses friction so no hardware or modifications to the printer are required. ... This is a remix...