crazyflie frame and fpv camera mount 3d models

The protective casing is specifically designed for the Bitcraze CrazyFlie quadrotor, incorporating an additional feature that enables mounting of a lightweight FPV camera and transmitter. The holder's hoop can support 1-gram cameras like this one...

This is a custom-designed mount specifically engineered to hold an FPV camera securely within the confines of a Blackout Clone frame, ensuring seamless integration and optimal performance.

First, I designed this simple camera mount using some basic tools, and then I attached the camera to the drone frame using double-sided tape. I tested this setup on two completely ordinary frames and was happy to find that it fits perfectly. To...

Camera Mount for STX225 Lens 12 and 13mm - 10 and 12mm higt

Based on the idea and design of Thingiverse's Cam-Mount #1456921, I redesigned the entire cam-mount since I dislike the aluminum spacer entirely. UPDATE: 04/24/2016 - I introduced Version 3, adjusting the mount point slightly backward and downward...

mounf for 19mm camera that slips over 30.5mm fpv drone frames

A case is designed to accommodate a FatShark 700 tvl camera and an ImmersionRC 600 mW transmitter on the front GoPro mount of a 3D Robotics Iris quadcopter platform. The transmitter box features cutouts at the front and rear, which enhance airflow...

Secure the LED strip wiring underneath the mount by sliding it over the rear standoffs and fasten in place with a single zip tie through pre-existing holes in the frame. ... **Print Settings:** * Printer: Prusia i3 * Rafts: No * Supports: Yes *...

To use, attach the frame to the drone's motor mounts and secure it with foam tape, ensuring not to damage motor wires. Place the battery beneath the quad board and fasten with tape once balanced. Positioning the battery underneath enhances stability....

These are ram air skirts and FPV camera mounts specifically designed for the DB3 frame by SecretAgent. They're built to be fully compatible with a range of HD camera mount accessories. To get your hands on this custom-designed frame or 3D prints,...

I picked up a cheap FPV camera for my RC, fixed wing aircraft and wanted to have a good mount and case for it. The idea was to have a couple of different threaded rods to set it for different aircraft so I could mount it in the cockpits for a pilot's...

DJI FPV Camera Mount designed specifically to: 1. Deliver optimal airflow to both the Camera and Transmitter. 2. Reinforce Antennas against impact forces. 3. Ensure easy access to SD and USB ports. 4. Offer multiple secure attachment points for the...

This FPV system mount takes your Rustler 4x4 to a whole new level of excitement! The camera pops up out of the windshield, requiring a precise cutout in the body to secure it perfectly. Printing with the back laid flat on the bed yields the strongest...

So I basically wanted a modified camera mount, then a modified top plate and also something to hold the motors both at the top and bottom. I combined the XF90 frame and the top plate claw into one piece for the top plate which now holds stop 8.5mm...

It's designed for full-size cameras like Runcam Swift, requiring a three-hole body with prominent features that slide into the mount and lock securely with two bolts. This mount is also compatible with Runcam's Night Eagle, which has a thicker body,...

The TX02 Ball and Socket Joint Mount provides a quick and easy way to adjust the camera's angle, while also ensuring excellent airflow for optimal cooling performance.

A simple and easy way to mount a 20x20mmVTX and a Nano sized 14mm wide camera on your UMX or other small fixed wing. Recommend printing on it's side in PETG. ...Happy flying!!!

For this robotic camera build, I recommend acquiring a RC805 remote controller transmitter from a well-known seller online, and attach it firmly by taping the back of the plastic housing using double-sided tape. ... Additionally, the instructions...

I snapped my previous camera mount within the initial seven days. Fortunately, this upgraded model features additional support structures for enhanced stability. Built using high-quality PLA filament, I employed the following printing parameters to...

I recently determined that xHover's original design wasn't ideal and didn't allow for adjusting the camera angle. Given my Runcam Swift 2, I modified it to accommodate this specific camera model effectively. Please share your thoughts on this...

Basic mount for a DJI FPV Camera in a Stingy V2 frame. Camera angle is approx. 20 degrees. You need 24mm or greater standoffs to fit the mount and camera. ... Made this since the XHover ones were taking awhile to arrive.

... rephrased the provided text in 60 words, focusing only on the rewriting and maintaining the core message of the original text. Any additional information or external references were excluded to ensure the rewritten text remains concise and relevant.

... in flight. Take a look and feel free to make adjustments as you see fit - I hope you enjoy working on it! Unfortunately, I'm getting an unexpectedly large number of RX Shelf models displayed, and I could have sworn I only uploaded one for reference.

This is a simplistic camera mount for a FPV camera on a F2 Mito GS frame. It is supposed to be printed in a flexible filament and you need _two pieces_. One piece printed as it is And one piece _mirrored_ -- using your favorite slicer software --...

Martian V2 Camera Mount Safeguards Your Valuable FPV Gear Against Crashes. ... A dedicated 32 FPV camera mount designed for the Martian v2 model, this rugged accessory protects your costly camera from damage in the event of a hard landing or crash.

Difficult to get in and out but that just means your camera won't fall out mid flight (Plan to refine the design when I have time to make it easier to get in and out of the mount). But till then this will definitely do the job. If you end up trying...

When I started getting airborne, I encountered a few issues - the prop guard and the camera mount kept breaking even when printed with PETG. The FPV camera would pop out easily during hard landings. To address this, I experimented with different...

I'm assembling a camera mount to complement the DJI Digital FPV system on the Skitzo Nova frame. ...The cage necessitates two 20mm standoffs, which are provided when utilizing my Air Unit Mount, available at https://www.thingiverse.com/thing:3863847.

... see it again? FPV camera and transmitter frame for under 200g drone. ...drone: RC EYE One Xtreme (Hitech multiplex) camera: CCD camera SW-240 (Sunmore Smart Technology Inc.) Transmitter: TS5823 http://plaza.rakuten.co.jp/cpu4edu/diary/201601130000/

some parts to fit the Sirians 135mm frame including antenna tube holders and vtx antenna holder and a mount to hold the Hawkeye Firefly camera (oldest version 1080p max) also a way to hold and protect a runcam phoenix nano possibly other nano cameras...