craftsman v20 3d models

Bracket that can be mounted to hold Craftsman V20 tools

Down + Dirty tool and battery hanger for Craftsman v20 cordless tools. ...

Craftsman V20 battery mount can be printed with no supports and 20% infill. ...There are two screw holes (4mm or less) for mounting and the head should be smaller than 10mm.

These are battery mounts I designed for the newer Craftsman V20 line of batteries. There are versions for both horizontal and vertical mounting. ...It is a little tight at first, but after about the first half hour of being used it forms to the battery...

I made a tool holder for Craftsman V20 series tools. I have been using prints from this design (https://www.thingiverse.com/thing:4728728) but thought I'd try something with a little bevel to it and make insertion easier. I print these on the long...

This is a battery adapter designed for a Craftsman V20 Battery, inspired by Griffin175's battery adapter (https://www.thingiverse.com/thing:3127879). I created this adapter without using any hardware to hold the contacts in place or requiring glue...

This is a rough likeness of the front height adjustment lever for a craftsman V20 lawnmower.

This is a remix from https://www.thingiverse.com/thing:398515 The original was too small for my Craftsman V20 drill so I re-created the basic design. The hole at the bottom/front is big enough for the front part of the chuck to fit through. It also...

This is a replacement part specifically designed for the Craftsman V20 line of battery-powered tools. A notorious design flaw inherent in the original equipment tends to cause it to malfunction and break, necessitating this replacement option. The...

This is a remix from https://www.thingiverse.com/thing:398515 The original was too small for my Craftsman V20 drill so I re-created the basic design. The hole at the bottom/front is big enough for the front part of the chuck to fit through. ...It also...

Just a very simple yet effective wall mount for the v20 batteries. It is sturdy enough for the larger batteries as well. ...Screw is offset due to the grooves in the battery.

a nice little hanger for your craftsman leaf blower. ...Make sure the hook on the bottom is unfolded.

UPDATE: Added holes to the V20 adapter to screw it into the C3 adapter. Just recycling screws from an old C3 Battery, they are like 2mm x 25mm with a 4mm cap. The battery is a snug fit but I might model a clip to screw under it for the lock. I...

UPDATE: Added holes to the V20 adapter to screw it into the C3 adapter. Just recycling screws from an old C3 Battery, they are like 2mm x 25mm with a 4mm cap. The battery is a snug fit but I might model a clip to screw under it for the lock. I...

This is an adapter to be able to adapt a Craftsman V20 sander with dust collection to a 1/4" vacuum. ...It works exceptionally well as in my testing, there has been virtually no dust left over.

Craftsman V20 4-1 Place Battery Non-Latching Holders MountCraftsman V20 Battery Holder Mount.Includes files for 4, 3, 2 and 1 battery holders. No supports needed. ...Print on edge as pictured.  Edit: Added files with 80mm and 40mm hole spacing.

# Why I had a specific need to use my Dyson upright vacuum's attachments on my craftsman v20 CMCVH001B handheld vacuum. # How - I designed this in Fusion 360 and printed it in PETG - The curves were annoying, but I think I got them all worked...

The user attaches the device to the factory mounting point, positioning the nozzle for optimal suction performance. ...This setup enables the vacuum to rest on the floor, effortlessly collecting dust heaps that are neatly swept in its direction.

I know there are one or two of these out there already, but they were flimsy and did not print well on my printers, so I printed my own that does not need supports at all. Its dead simple and strong. I put a few different sizes so that depending on...

The blower only comes with a short round tube with a circular end, so I designed these additional extensions with a flared flat end because I am tall and didn't want to bend over to get the air to the floor. I designed it in Wings3D and include...

I designed this safety key on the off chance that I lose the original.

I designed this safety key on the off chance that I lose the original.

If you'd like to support me you can post a make, comment and/or pay me a coffee at PayPal -------------------------------------------- Nozzle made for Craftsman V20 Blower. Does it make any difference? I have no idea, but I had a lot of fun creating...

Human: Craftsman. There's a script to transform tris into quads, but it's not just for this model - it's also a gift that can be used on any model. You'll find a script to retopology models using instant meshes bridge and instant meshes. To run...

If you'd like to support me you can post a make, comment and/or pay me a coffee at PayPal--------------------------------------------Nozzle made for Craftsman V20 Blower.Does it make any difference? I have no idea, but I had a lot of fun creating...

I'm not able to assist with that request.

Basic SINAMICS V20 converters, compatible with SolidWorks

This is an LG V20 Incipio phone case.