craftsman table saw zero clearance insert 3d models

{Edited 3/31/21} This is a zero clearance insert for a 10 inch Craftsman 137 contractor table saw. The insert is 69 mm wide and 255.2 mm long (Measured from the top of the opening bevel located on the top and left edges). The main part of the board...

Craftsman Model 113 Contractor Table Saw replacement throat plate with splitter. Requires 2x 10-32 machine screws and 1x 10-32 nut. For small volume printers like an Ender 3 or Prusa MkX, print front and back half then put both pieces together...

Model for a zero clearance insert for a craftsman 137 job site table saw, designed to fit perfectly in place without any clearance issues. I created this insert because I couldn't find one that matched my dado stack requirements; the manual listed...

Zero clearance inset / throat plate for Craftsman miter saw (model 137.212290). Bought the saw used and the throat plate was cracked and falling apart. I taped up the remnants and modeled a new one since these are impossible to find. Print with...

This is a zero clearance insert I designed to replace the flimsy OEM insert on a Makita **MLT100N** table saw. I do not know if this is compatible with the **MLT100** or not, but it might. -You'll notice that the screw holes are counterbored from...

I wanted a zero clearance insert for my DeWalt DWE7485 jobsite saw and printed another I found online but it didn't fit my saw very well so I set out and whipped this one up. The insert fit well enough and was fairly straight forward to level with...

I resized and mirrored the design to fit my saw perfectly. As yet, I haven't printed it out, so I'm unsure if it's functional. The size requires it to be printed in two separate parts. I intend to print this on either a MakerBot Replicator 2 or an...

... screws. It can be printed on most common household 3D printers. While it is tailored for my particular table saw, I’m hoping that the design can be tweaked to fit other left tilting saws. More information, STEP and Fusion 360 file available.

... I’m hoping that the design can be tweaked to fit other left tilting saws. [More information, STEP and Fusion 360 files](https://arcady.genkin.ca/2020/10/ultimate-3d-printed-table-saw-throat-insert-with-dovetailed-zero-clearance-strips/) available.

I designed an all-in 3D printed table saw throat insert. It features changeable dovetailed zero clearance strips that are easy to make from 1/4″ birch plywood. The insert allows full range of movement of blade and splitter (height and tilt angle). It...

Zero clearance (at 90 degrees) insert designed specifically for the MasterForce 10" jobsite tablesaw MJ10250VDJT, carefully crafted using a caliper on the stock insert and adjusted to accommodate a 1/8" kerf blade while ensuring that the ribbing...

I needed a custom template for my DW7491 table saw to cut zero-clearance inserts with precision. This straightforward design enables you to accurately cut rounded ends using a flush-trim bit on your router. The template covers the semi-circular edges...

This is a zero clearance insert for the Bosch GTS10XC table saw. The model has already an opening for the riving knife to pass trough. As the model is too big to be printed as a whole on most printers, a 2-part model is also provided. I used...

This is a simple and straightforward zero-clearance insert designed specifically for use on the Craftsman 10-inch tabletop bandsaw, which has a part number of 113-244513.

The Zero Clearance design for the Nototec 25102

A quick replacement of the stock zero clearance insert on the WEN 3959 benchtop band saw. Stock photo shows the gap it leaves, which allows small cut offs to fall in. This new insert also reduces tear-out. ...I printed at 50% infill with tree supports...

I upgraded the standard stock insert on my DW715 Dewalt Miter saw with a custom-made zero clearance insert. After several months of use, it still looks like new and shows no signs of wear or damage. ...The design is compatible with a long bed 3D...

I designed a Zero Clearance Kerf Band Saw Insert for my 14" Jet bandsaw. I'm confident it will work with other brands as well, thanks to its 2.5" hole. ...Here are the print settings I used: Printer: DIY Rafts: No Resolution: .20 Infill: 100% Notes: I...

Zero clearance insert for the Dewalt DWS780 miter saw made with Fusion 360. I printed mine on a CR10 V2. ...Since the part is so big, I had to orient it vertical and at a slight angle to make it fit the buildplate.

Zero Clearance Insert for the Hitachi 10FCH2 Saw (Should also match the Metobo C10FCH2). Works fantastic, just needs some minor adjustment to avoid sanding to install. I will fix the fit just a bit in the next revision I produce. ...For now, if you...

I designed a zero-clearance insert to replace the standard stock insert on my DW715 Dewalt Miter saw. After several months of use, it still looks almost brand new with no significant signs of wear. The only caveat is that it needs a long bed, which I...

I created a zero clearance insert to replace the standard stock insert on my DW715 Dewalt Miter saw. This one has been in use for a few months now and doesn't show any serious signs of wear. ...It requires a long bed (I have a prusa i3), but it it could...

This is a zero clearance insert for Dewalt miter saws.I modeled it from the insert on my own saw wich is a DW716 (12inch, dual bevel, NON sliding)from what I can tell from the replacement inserts on amazon, this will fit...

Zero clearance insert for a Ryobi TS1345L. Should work with anything in the 1345 line (the L is the refurb model). Uses the screws from the existing throat plate. Once it was installed, I cut the slot with multiple small cuts. The PLA melted...

Remix of Saur0n's EMS216L insert Plate but to fit the TSS103. ... Using PrusaSlicer modifiers I printed the middle third at 100% infill and the sides at 50%.

print solid, saw through once installed for precision fit. ... works a treat on discontinued saw.

* zero clearance table saw insert * throat plate * (modelled in 2 parts for smaller printers) * * this is my first project in OpenSCAD! * please provide support or improvements by commenting * * TO DO: * - make the number of interlocking...

Two custom table inserts fit perfectly for the Craftsman 113.243310 12-inch band saw, designed specifically to meet its unique needs. Since standard inserts wouldn't work on this model, I created two versions using DesignSpark Mechanical software. A...

This is a DIY project based on bpopp's custom Dewalt table saw dado throat plate design. I've modified the original to accommodate a standard blade, allowing users to create openings that match their specific needs. ...The updated version appears...

There are two models here. V3 is slightly larger than V2 to account for a small amount of plastic shrinkage. ...V2 is the exact size.See it installed and tested here