craftsman table saw handwheel 3d models

Replacement handwheel for Craftsman Table Saw, model 113.221620. The handwheels raise/lower the blade and tilt the blade. These fit over the D-shaft. These handwheels may work with any D-shaft with diameter of 3/8-inch. It fits over 5/8-inch of...

I own a Delta 36-650 Contractor table saw and the adjustment handwheel (part number 902900) has snapped. Instead of ordering a replacement, why not just print one! Print one copy of the wheel and one handle, then use a #8 screw to attach the handle...

I swapped out the original blade height adjustment and angle wheel on my Craftsman Table Saw for a custom replacement.

A craftsman's essential tool - the 137.228010 table saw. Its crank, crafted with precision, allows for effortless adjustments. The operator thoughtfully designed the crank handle hole to be slightly undersized, ensuring a secure grip when threading...

I was eager to create a miter sled for my Craftsman Table Saw, but discovered the cost of the rails to be prohibitively expensive, so I decided to design and build my own instead. ...These custom-made rails are 200mm long and feature five holes for #10...

I was missing a handle on my old Craftsman table saw and found it annoying to turn the knob without it. So I modeled a new one using Tinkercad to replace it. The model uses a 50mm long 3/8" bolt and nut because that's what I had on hand and threaded...

This is a replacement handle I designed for my Craftsman table saw. My old one broke and I couldn't get it glued back together! Similar parts sell online for anywhere from 15 to 35 dollars. This design will also work with an Ace branded 10-inch table...

Craftsman 10'' Table Saw (Model # 315218060) Gear Rack - Part # 0134010228 #88 https://www.searspartsdirect.com/model/319si7aknn-000247/craftsman-315218060-table-saw-parts

... on this one (https://www.thingiverse.com/thing:2767618) by https://www.thingiverse.com/wt808. ... It was modified for an 1 1/4" Vacuum connector and a wider shield 34mm vs. 30mm. This is specifically for Craftsman Table Saw Model 315.228310. ...

I have a Sears/Craftsman 9 Inch Table Saw and could not find a good file on here that worked. My table saw has a .500 (12.7mm) with the flat to round dimension measuring .400 (10.16mm). Handwheel body is 3.5" in Diameter. The handle knob is 2.5"...

I designed and printed custom miter locks to work with the Powertec Featherboard on my Craftsman table saw because the original locks were incompatible with it.

An adapter between a Craftsman 10" Table Saw CMXETAX69434502 and a ShopVac QSP hose with the nozzle removed. Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer!

Replacement Craftsman table saw stand leg end cap. Original broke (see black part in photo). Designed a replacement with more support than the original -- thicker around the sheet metal and taller. ... No supports needed.

The Craftsman 113 10-inch table saw top offers a high-quality and reliable cutting experience for woodworking enthusiasts. With its large 10-inch blade, this table saw is perfect for a wide range of projects. ...Its durable construction ensures...

I lost a foot for the Craftsman job site table saw, so I took one off one of the others (Black) and modeled a new one (Red) from the original.The final print was printed with the remainder of my red and finished with black.

This is a replacement for the outer belt guard (part 824359) for a Craftsman 113 table saw (specifically for 113.299315, but may fit others). This part is a subassembly of part 824360 which is both halves of the guard. ... I have also included a...

I've created a custom 10" Table Saw Belt Guard designed to replace the Craftsman Part #: 60252. The Fusion 360 archive file is included, featuring a parametric design that allows for easy customization. ...Key parameters such as Pulley Hole Diameter,...

I purchased a feather board from Harbor Freight, but unfortunately, the rail guide was too wide to fit my Craftsman table saw. To solve this issue, I created an adapter that fits the rail width of approximately 15.5mm. When you tighten the knob, the...

This knob fits the common 10in table saw "white labeled" to Craftsman, Tradesman etc starting in the early 2000's. The arrival knife in the back is removed with a 10mm wrench. This print makes the arrival knife much quicker to uninstall without...

This is a straightforward replacement for a defective Crank Wheel on my Craftsman Table Saw. The saw employs two of these wheels, one for controlling blade depth and another for adjusting the blade angle. Both wheels feature a unique keyed nut that...

Two custom table inserts fit perfectly for the Craftsman 113.243310 12-inch band saw, designed specifically to meet its unique needs. Since standard inserts wouldn't work on this model, I created two versions using DesignSpark Mechanical software. A...

... fillet on the surfaces that led to me printing with supports and then having to sanding it off. I'm not in love with how the surface finish turned out, but it lives under the table of the saw, in a basement, covered in dust, so choose your battles.

... but I was unsuccessful in getting them. ...As you can see, it's not very complicated, and it serves its purpose of moving smoothly across the cutting table, the material although could have been better in ABS I made it with what was available at hand.

This straightforward method assists me in organizing my garage, created using CATIA and featuring a compatible .stp file for integration into other CAD systems.

... smaller table saw uses a different track than the one I had before so I had to modify the bar. It fits the Craftsman 10-in Table Saw CMXETAX69434502 This is my first creation I have uploaded - comments welcome and appreciated. ... Happy Printing!

... size replica of the original. ...I recommend PLA or any easy to print plastic, since it's just going to be worn away eventually anyway. It replaces Craftsman part number 69156 table insert, and fits band saw models 113244510, 113244512, 113244513.

This is a CRAFTSMAN 10-in 15-Amp Table Saw sawdust exhaust adapter for the 3 gallon shopvac. After downloading several which said their measurements were correct, I found none of them would work. I took measurements and gave the design over to Robert...

A zero-tolerance dado throat cover specifically designed for Craftsman 137 table saws is now available. This updated model features a precise 1/8 kerf, ensuring accurate cuts every time. The design has been revised to correct the minor dimensional...

Designed specifically for this saw, but also compatible with other Craftsman/Skilsaw table saws that feature a similar mitre slot design. The rail is intentionally shortened to allow for the placement of washers underneath, thereby elevating it above...

{Edited 3/31/21} This is a zero clearance insert for a 10 inch Craftsman 137 contractor table saw. The insert is 69 mm wide and 255.2 mm long (Measured from the top of the opening bevel located on the top and left edges). The main part of the board...