craftsman table saw 3d models

I swapped out the original blade height adjustment and angle wheel on my Craftsman Table Saw for a custom replacement.

I was eager to create a miter sled for my Craftsman Table Saw, but discovered the cost of the rails to be prohibitively expensive, so I decided to design and build my own instead. ...These custom-made rails are 200mm long and feature five holes for #10...

I was missing a handle on my old Craftsman table saw and found it annoying to turn the knob without it. So I modeled a new one using Tinkercad to replace it. The model uses a 50mm long 3/8" bolt and nut because that's what I had on hand and threaded...

This is a replacement handle I designed for my Craftsman table saw. My old one broke and I couldn't get it glued back together! Similar parts sell online for anywhere from 15 to 35 dollars. This design will also work with an Ace branded 10-inch table...

Craftsman 10'' Table Saw (Model # 315218060) Gear Rack - Part # 0134010228 #88 https://www.searspartsdirect.com/model/319si7aknn-000247/craftsman-315218060-table-saw-parts

... on this one (https://www.thingiverse.com/thing:2767618) by https://www.thingiverse.com/wt808. ... It was modified for an 1 1/4" Vacuum connector and a wider shield 34mm vs. 30mm. This is specifically for Craftsman Table Saw Model 315.228310. ...

Replacement handwheel for Craftsman Table Saw, model 113.221620. The handwheels raise/lower the blade and tilt the blade. These fit over the D-shaft. These handwheels may work with any D-shaft with diameter of 3/8-inch. It fits over 5/8-inch of...

A craftsman's essential tool - the 137.228010 table saw. Its crank, crafted with precision, allows for effortless adjustments. The operator thoughtfully designed the crank handle hole to be slightly undersized, ensuring a secure grip when threading...

I designed and printed custom miter locks to work with the Powertec Featherboard on my Craftsman table saw because the original locks were incompatible with it.

Replacement Craftsman table saw stand leg end cap. Original broke (see black part in photo). Designed a replacement with more support than the original -- thicker around the sheet metal and taller. ... No supports needed.

An adapter between a Craftsman 10" Table Saw CMXETAX69434502 and a ShopVac QSP hose with the nozzle removed. Customized version of https://www.thingiverse.com/thing:1246651 Created with Customizer!

I purchased a feather board from Harbor Freight, but unfortunately, the rail guide was too wide to fit my Craftsman table saw. To solve this issue, I created an adapter that fits the rail width of approximately 15.5mm. When you tighten the knob, the...

This is a straightforward replacement for a defective Crank Wheel on my Craftsman Table Saw. The saw employs two of these wheels, one for controlling blade depth and another for adjusting the blade angle. Both wheels feature a unique keyed nut that...

This straightforward method assists me in organizing my garage, created using CATIA and featuring a compatible .stp file for integration into other CAD systems.

... fillet on the surfaces that led to me printing with supports and then having to sanding it off. I'm not in love with how the surface finish turned out, but it lives under the table of the saw, in a basement, covered in dust, so choose your battles.

... but I was unsuccessful in getting them. ...As you can see, it's not very complicated, and it serves its purpose of moving smoothly across the cutting table, the material although could have been better in ABS I made it with what was available at hand.

Designed specifically for this saw, but also compatible with other Craftsman/Skilsaw table saws that feature a similar mitre slot design. The rail is intentionally shortened to allow for the placement of washers underneath, thereby elevating it above...

This is a replacement for the outer belt guard (part 824359) for a Craftsman 113 table saw (specifically for 113.299315, but may fit others). This part is a subassembly of part 824360 which is both halves of the guard. ... I have also included a...

Customized Version of http://www.thingiverse.com/thing:97238 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=97238 Instructions Using the Following Options: Bandsaw Length Set to 24 Inches Inside...

Customized version of https://www.thingiverse.com/thing:4859523 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4859523

This is a custom crank-handle-adjustment-knob replacement for the Craftsman table saw, an 8-inch direct drive model with 15 amps of power. The original handles often broke down quickly, so I created this alternative. It comes with a 19mm socket or...

I've created a custom 10" Table Saw Belt Guard designed to replace the Craftsman Part #: 60252. The Fusion 360 archive file is included, featuring a parametric design that allows for easy customization. ...Key parameters such as Pulley Hole Diameter,...

This knob fits the common 10in table saw "white labeled" to Craftsman, Tradesman etc starting in the early 2000's. The arrival knife in the back is removed with a 10mm wrench. This print makes the arrival knife much quicker to uninstall without...

A zero-tolerance dado throat cover specifically designed for Craftsman 137 table saws is now available. This updated model features a precise 1/8 kerf, ensuring accurate cuts every time. The design has been revised to correct the minor dimensional...

I split the original model file to enable printing on my Ender 3Pro. Two rail parts will fit on an angle. ...needs to be adjusted for more clearance in height.

Customized version of https://www.thingiverse.com/thing:4859523 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4859523

Customized version of https://www.thingiverse.com/thing:2925024 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2925024

Customized version of https://www.thingiverse.com/thing:2925024 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2925024

{Edited 3/31/21} This is a zero clearance insert for a 10 inch Craftsman 137 contractor table saw. The insert is 69 mm wide and 255.2 mm long (Measured from the top of the opening bevel located on the top and left edges). The main part of the board...

These adapters fit the factory guard of vintage Sears Craftsman model 113 contractor-style 10" table saws, including the 113.298142, 113.298032, and 113.298240 models. A dust hose adapter fits 2.5" Shop-Vac style hoses securely in place. To attach...