craftsman drill holder 3d models

Drill bit index for Craftsman 1950's Carpenters Wall Cabinet

This is a remix from https://www.thingiverse.com/thing:398515 The original was too small for my Craftsman V20 drill so I re-created the basic design. The hole at the bottom/front is big enough for the front part of the chuck to fit through. It also...

It also fits an older Craftsman 18v drill I have. Print Settings Printer Brand: Creality Printer: Ender 3 Pro Rafts: No Supports: No Resolution: 0.2 Infill: 5-20% Filament: Geeetech PLA Grey Notes: Any material does the trick. Category: Tool...

This is a replacement for the chuck key holder on the Craftsman 10in Drill Press (Model No. 137-219001). The barrel of the chuck key, where it clips in (see picture) is Ø0.390". ...

The barrel of the chuck key, where it clips in (see picture) is Ø0.390". Print instructionsCategory: Tool Holders & Boxes Summary This is a replacement for the chuck key holder on the Craftsman 10in Drill Press (Model No. 137-219001). ...The barrel...

A Replacement Drill Press Handle: Upgrade Your Craftsman Model This innovative handle is designed to replace the broken lowering and raising table handle on your Craftsman 34" drill press model, but its versatility makes it compatible with others.

... I found a metric bolt and nut of the correct size to fasten the handle. (I neglected to note what the size was. I will update when I measure it later) I also tapped the set screw (grub screw) hole to take the original Craftsman handle set screw.

here is another part off my craftsman drill press

Has mounting hole to attach to Craftsman 20v Drill/Drivers using the 3mm preinstalled nut. You will need to purchase a 3mm x 16mm screw to secure this to your drill. This holder has a friction fit which will hold bits securely but some may slide...

Craftsman 20 Volt battery holder, Battery can be placed from either end, Same design both ends, can be installed either way.

It works with my 2 Ah (29141, 40V DC 73Wh { http://www.craftsman.com/craftsman-40v-lithium-ion-battery/p-07198740000P }) and my 4 Ah (138.98742, 40V DC 146Wh { http://www.sears.com/craftsman-40v-rechargeable-lithium-ion-battery-98742/p-07198742000P...

It's now successfully holding both my 2 amp-hour (29141, 40V DC 73Wh { http://www.craftsman.com/craftsman-40v-lithium-ion-battery/p-07198740000P }) and my 4 amp-hour (138.98742, 40V DC 146Wh {...

Bracket that can be mounted to hold Craftsman V20 tools

I needed a place to store my 3 piece Craftsman pry bar set. ...I mounted it to the side of my workbench. I noticed there was some flex to the holder, so I added some side braces to stiffen it up a bit.

The holder was specifically designed for Craftsman double ratcheting wrenches so it may not fit your wrench….. ...but figured I'd share for the odd chance someone out there could use it. PrintingPrinted @ 0.3mm layer, 20% infill, no support needed ~...

Battery wall holder for Craftsman 20v batteries. This is a nice and convenient way to keep your batteries ready and accessible for when you need them. I use 1/4" bolts that are 3/4" long to install on my slat wall but I have included a file without...

This is a small piece that keeps the craftsman screwdrivers in one place with friction

I made a tool holder for Craftsman V20 series tools. I have been using prints from this design (https://www.thingiverse.com/thing:4728728) but thought I'd try something with a little bevel to it and make insertion easier. I print these on the long...

This dust guard protects the spindle on vintage (1930s-1950s) Craftsman, Atlas and Dunlap drill presses. Model created directly from an original pot metal dust cover. ... These sit loosely in the hole at the top of the belt guard, they should be easy...

Replacement part created for a damaged Craftsman 8-inch drill press, which had stopped working. Made from strong ABS material and designed with 100% infill to ensure stability. ...Designed using the precise tools of Sketchup software, where the original...

I have a Craftsman table top drill press, that I need to put a light ring on. 2 sided tape kept falling, so I decided to try my hand at modeling one. Went better than expected, but I'm just a beginner with Fusion 360. ... I can upload the F3D part if...

I needed a solution to hang my craftsman tools up out of the way. ...They came with a built in hanger but nothing to hang them on.This attaches easily to the wall and holds my tools with the hooks they cam with.</p>

This was designed and printed to replace a broken crank arm on my drill press. I used a 1/4-20 x 3" bolt for connecting the two together, with 2 washers place between the handle and arm. ...I used a 5mm bolt to keep it secured to the drill press.

This was designed and printed to replace a broken crank arm on my drill press. I used a 1/4-20 x 3" bolt for connecting the two together, with 2 washers place between the handle and arm. ...I used a 5mm bolt to keep it secured to the drill press.

This was designed and printed to replace a broken crank arm on my drill press. I used a 1/4-20 x 3" bolt for connecting the two together, with 2 washers place between the handle and arm. I used a 5mm bolt to keep it secured to the drill press. ...Print...

Battery holder for 19.2 Craftsman batteries

Wire spool holder for early 90s Craftsman MIG welder.

CRAFTSMAN CMHT37109: