craftsman 109 lathe parts 3d models

A metal lathe's feed lever, specifically the Craftsman 109 model, can be adjusted to control the speed at which the workpiece is fed into the cutting tool. ...This feature allows for precise and accurate cuts while using this lathe.

The metal lathe compound swivel base from Craftsman's model 109 is designed for precise and versatile cutting operations. ...This sturdy and reliable base allows for easy adjustment and rotation of the head, making it a great tool for any woodworking or...

Change gears for the Craftsman Model 109 Lathe. This should be the complete set with the following gears: 32T, 36T, 40T, 44T, 46T, 52T, 54T, and 56T. The fit of keyways and axles may need to be sanded just a bit to get them to fit correctly. I've...

Organizer for Sears / Craftsman / Dunlap / AA Model 109 Lathe change gears. Two versions included: tall and short. ... Short one uses less filament, but the gears aren't as constrained.

Organizer for Sears / Craftsman / Dunlap / AA Model 109 Lathe change gears. Two versions included: tall and short. ...Short one uses less filament, but the gears aren't as constrained.</p> Category: Machine Tools

Change gears for Sears / Craftsman / Dunlap / AA Model 109 Lathe. Through hole and slots are a little bit oversized to accommodate the tolerances on my printer. I still clean up the hole with a 1/2" drill, but the slots typically require no...

My local hackerspace got a Craftsman 109 Lathe but it did not have the semi-circular Rocker that is required for the Tool Post. I designed this one to get by. I am not pretending this is as good as a metal Rocker, but a plastic Rocker is better...

Change gears for Sears / Craftsman / Dunlap / AA Model 109 Lathe. Through hole and slots are a little bit oversized to accommodate the tolerances on my printer. I still clean up the hole with a 1/2" drill, but the slots typically require no...

I recently purchased a Craftsman 109 lathe off of Craigslist. Unfortunately, not all of the gears were present. After a LOT of hunting, I finally found all of the information I needed to create DXFs for the gears at <a...

I recently purchased a Craftsman 109 lathe off of Craigslist. Unfortunately, not all of the gears were present. After a LOT of hunting, I finally found all of the information I needed to create DXFs for the gears at http://www.geargenerator.com/. ...

I recently acquired a Craftsman 109 lathe from Craigslist, but I was missing several gears. After an extensive search, I finally found the necessary information to generate DXFs for the gears at geargenerator.com. Once I had all the files, I cleaned...

I created this specialized cutout tool specifically for the Craftsman 109, which boasts a compact spindle design. ...By leveraging this unique feature, users can effortlessly tackle intricate cuts in smaller components, significantly reducing complexity...

Atlas/Craftsman 12-inch lathe parts. My one-piece saddle features a 10d-9 cast at its bottom, making it extremely difficult to find. I possess two of these lathes; one suffered significant damage in a building fire, so I will add extra components as...

This is a crucial gear spacer designed specifically for the Craftsman 109 lathe, allowing users to effectively utilize the various gears available on this machine.

This is a result of reverse engineering a headstock of a 1950's era Craftsman 109 hobby lathe. FYI, the gears are faked in. (No involute curves.) There's probably a couple other things missing or not exactly right. I didn't end up needing this,...

The vintage 1932 model of lathe features a functional and precise cross slide dial that is still sought after by craftsmen today. ...This mechanical device allows users to adjust the tool's position with utmost accuracy, making it an essential component...

I designed a gear change system inspired by the Atlas 618/Craftsman 101 6" lathe's configuration, utilizing available gears as reference points. ...The dimensions were determined based on the few gears at my disposal, which might not match your setup,...

This is a genuine reproduction of the original drive pulley used on the Craftsman/Atlas 1/2 drive motor shaft, offering precise compatibility and reliable performance.

This text pertains to small cones used in a lathe for shaping small objects. The instructions were created using Repetier firmware version 2 at high settings with 100% infill, three shells, and a layer height of 0.15mm. ...The extruder temperature was...

This is a design I'm finally proud to share with the world.\r\n\r\nThese inserts were born from my love for the premium ones designed for akro-mils parts organizers, but I've always preferred the Craftsman brand available at Lowes, so I took it upon...

These are replacement parts for an antique Craftsman walking lawn sprinkler that's been around since the dawn of time. ...Although it still manages to function, its ancient gears are starting to show signs of wear and tear - the grub gear and bushing...

This fits the Craftsman 351183050 1/2 inch stapler. It could also work with the brad nailer. ...Made with Gizmodorks TPU material.

Fits Craftsman 351183050 1/2 inch stapler. It may also fit the brad nailer. Printed in gizmodorks tpu Category: Tools

This was an awesome find and allows me to maximize the use of my parts bins. I had a minor issue with the originals due to a large circular void in the first layer when printed. This caused a buildup of material in the second and third layers and...

... for a setscrew, but it fits so snugly on my lathe that I didn't need to use the screw. This modification may work on other Atlas/Craftsman 618 Lathes, but it was specifically designed for this model - http://www.lathes.co.uk/atlas6inch/page2.html.

This replacement cover is designed for a vintage Craftsman / Atlas lathe from 1935. It securely attaches to the cross-slide, shielding the threads and providing protection. ...The design has been updated, with modifications made to the .scad file so...

This is a replacement handwheel designed to fit an antique 1935 Craftsman/Atlas lathe, complete with a comprehensive knurling library crafted by a skilled individual elsewhere.

To mount the Clough42 ELS on the rear of the lathe, I needed a little more thread on the lead screw and decided to replace the lead screw support with a slightly shorter version. Additionally I used two thrust bearings to react the preload. I didn't...

This is a collection of highly detailed scratch-built parts for the legendary Messerschmitt Bf 109 G fighter plane.

This is a remix of the Craftsman parts organizer insert by dlinsmeyer. ...I created an empty one so you can add your own bin dividers and a 4 slot one.