craftbot plus 3d models

For bigger undertakings.

Craftbot 2 Filament guide Tube holder

A Three-Dimensional Rendering of the CraftBot Bed.

Mount four Magigoo bottles securely onto your Craftbot 3 3D printer with ease. ...This mounting system is specifically engineered for use with the Craftbot 3 model, ensuring a seamless integration that maximizes performance and efficiency.

Sunlu Dryer Mount for the Craftbot Flow. I printed this in ABS with 5 shell / 50% infill.. 0.3mm layer. ... Printed on its side, with no support required.

Craftbot Pro Fan Duct for Hexagon Hot End Print Configuration Printer: Craftbot Pro In order to create a high-quality print, the printer settings need to be adjusted. Resolution: 0.2mm Infill density plays a crucial role in achieving optimal...

This spoolholder shaft - Fits on standard Craftbot spool holder axles (10.2 mm diameter x 100 mm unobstructed cylindrical length) - Minimises friction by means of two type 6003 ball bearings (17 mm inner x 35 mm outer x 10 mm depth) - Has a rim...

To link a polybox to a craftbot flow index, simply remove the nut from the base of the guide tube holder and swap it out for the pre-printed component.

Rob designed a specialized filament guide for the CraftBot, featuring an extended arm that expertly navigates the filament from larger reels. ...He created this innovative solution and has given it his official seal of approval to be shared here.

... press the other side on, applying minimal force to avoid breaking off any arms. Upgrade your Craftbot here: https://www.craftbot.nl/product/eu-hotend-upgrade-for-the-craftbot-reliable-printing-exotic-filaments-incl-eu-shipment-and-incl-tax/

The ergonomic lever is an innovative addition designed by me to simplify leveling the Craftbot 3. ... Just print out the replacement part, apply some heat to the existing control dial, and then snap it securely into position.

Simple side covers for the Craftbot Flow. Just print and assemble with an elastic band in the middle, just put it over both hooks. ... Printed in PLA at 0.2 infill 25%...

This is an upgrade of G0dl1ke's Hinge settings. ...Print Settings are as follows: Printer: Craftbot+. Rafts will be omitted. Supports will not be printed. Resolution has been set to 0.2mm. ...Infill density will be 80%.

This foot for CraftBot FLOW printers fits over the original rubber foot. ...It should be used with a double yellow dot squash ball (the softest ball) and will dampen the vibrations of the printer.

A 3D printable version of the standard metal filament holder provided with the Craftbot Flow printer (may fit others) I've included one the standard length and one 20mm longer. ... Printed in PLA at 60% infill for strength at 0.16mm layers

It may not fit non-"Flow IDEX" Craftbot printers as-is, but may do so after adapting the enclosed OpenSCAD source file and re-rendering: - Download and install OpenSCAD from https://www.openscad.org - Launch OpenSCAD and open the enclosed OpenSCAD...

My Mosaic Palette 2 Mount for the Craftbot saves valuable desk space and seamlessly integrates the Pallete 2 with the printer. I printed this mount using Kodak PLA Tough filament with a 0.8 nozzle diameter, strong enough to hold it securely. The...

My Mosaic Palette 2 Pro mount for the Craftbot saves desk space and integrates the Palette 2 more seamlessly with the printer. I printed this using Kodak PLA Tough .8 nozzle, which holds its shape easily due to its toughness. The vents at the back...

It´s sized to fit on a CraftBot Flow XL printer, and it leaves space on the sides so that the heads will stay a fair way apart. ... The connections between the squares help removing the single layer print ;-) Try lifting only one edge and you should...

This upgrade encompasses a comprehensive adjustment package tailored specifically to augment current configurations of CraftBot print platforms. ...Key refinements within revised *.stl file revisions revolve around optimized door functionality and...

2) Enlarge the thermistor hole in the Chimera heating block by drilling, so it can accept a stock CraftBot thermistor. 3) Cut the M6 nozzle throat in the section where there's no thread. 4) Heat up the nozzle throat. I heated the nozzle throat on my...

I was never fully satisfied with CraftBot's initial thin filament holder, so I created a simple yet elegant gear bearing for smoother rotation. Most of the filament rolls have a 56mm hole diameter and 75/90mm width, so they were my target. I began by...

I built this to perfectly synchronize the two belts in my CraftBot by adjusting them to equal tension. It requires a wooden dowel. The printed parts will grip the middle of the pulleys while you can pull the wooden dowel towards the back of the...

... sets the correct step for the extruder motor. For project discussion, head over to CraftBot's forum: https://craftbot.com/forums/view-thread/4314 If you have any further questions or concerns, feel free to reach out. ...Good luck with your prints!

The only negative is that you will have to reduce the useful printing area to 240 (X) * 180 (Y) * 200 (Z) The material you need to buy is: 1- Dual Gear extruder...

This is a simple and easy to print ball bearing spool holder for Craftbot printers, to be clamped onto their genuine friction type 10.5 mm diameter / 99 mm open length spool holder. It uses two standard 608 (skateboard) ball bearings. ...

Designed from scratch in FreeCAD, this stock hotend duct is a reimagined take on the Craftbot+ Fan Duct by sepp974. Key improvements include a better fit to fan angles, enhanced airflow through ducts, and a more centralized design around the hotend.

The CraftBot shines with exceptional performance as high-quality hardware. However, the stiff yet flimsy little nylon screw used to hold the print bed in place is a noticeable design flaw. One of my prints failed drastically due to the vibrations...

I designed a simple fan duct for the Craftbot, specifically made for Bart's hotend upgrade. I printed it in ABS to add extra safety features, and while PETG should also work well, I wouldn't recommend using PLA without first testing its...

This printable clip is designed for use with a CraftBot printer bed to securely hold the rear edge of a PRINTinZ Printer plate in place. It works best when paired with M3 thumb screws along the front edge. Due to variations in thickness among...