craftbot 3 3d models

Craftbot Pro Fan Duct for Hexagon Hot End Print Configuration Printer: Craftbot Pro In order to create a high-quality print, the printer settings need to be adjusted. Resolution: 0.2mm Infill density plays a crucial role in achieving optimal...

This foot for CraftBot FLOW printers fits over the original rubber foot. ...It should be used with a double yellow dot squash ball (the softest ball) and will dampen the vibrations of the printer.

This is an upgrade of G0dl1ke's Hinge settings. ...Print Settings are as follows: Printer: Craftbot+. Rafts will be omitted. Supports will not be printed. Resolution has been set to 0.2mm. ...Infill density will be 80%.

Rob designed a specialized filament guide for the CraftBot, featuring an extended arm that expertly navigates the filament from larger reels. ...He created this innovative solution and has given it his official seal of approval to be shared here.

Simple side covers for the Craftbot Flow. Just print and assemble with an elastic band in the middle, just put it over both hooks. ... Printed in PLA at 0.2 infill 25%...

To link a polybox to a craftbot flow index, simply remove the nut from the base of the guide tube holder and swap it out for the pre-printed component.

... press the other side on, applying minimal force to avoid breaking off any arms. Upgrade your Craftbot here: https://www.craftbot.nl/product/eu-hotend-upgrade-for-the-craftbot-reliable-printing-exotic-filaments-incl-eu-shipment-and-incl-tax/

As an alternative to supergluing the magnets you may drill their boreholes to 3.9 mm, the borehole entry some 3 mm deep to 4.0 mm and then press the magnets into the 3.9 mm holes. As always I include the OpenSCAD source files for you to adapt and...

This print requires mounting with 2 to 3 M3X20mm or 25mm screws securely to the body of the Craftbot. If printing one holder, center back is the ideal spot for attachment with an extra screw hole adding sturdiness. However, it does allow up to 8...

A 3D printable version of the standard metal filament holder provided with the Craftbot Flow printer (may fit others) I've included one the standard length and one 20mm longer. ... Printed in PLA at 60% infill for strength at 0.16mm layers

I've remade http://www.thingiverse.com/thing:717962 to work flawlessly with my Craftbot Plus printer. ...To ensure a smooth filament flow, I employed a 2mm drill to widen the hole, making it easy for the filament to pass through.

It may not fit non-"Flow IDEX" Craftbot printers as-is, but may do so after adapting the enclosed OpenSCAD source file and re-rendering: - Download and install OpenSCAD from https://www.openscad.org - Launch OpenSCAD and open the enclosed OpenSCAD...

My Mosaic Palette 2 Pro mount for the Craftbot saves desk space and integrates the Palette 2 more seamlessly with the printer. I printed this using Kodak PLA Tough .8 nozzle, which holds its shape easily due to its toughness. The vents at the back...

My Mosaic Palette 2 Mount for the Craftbot saves valuable desk space and seamlessly integrates the Pallete 2 with the printer. I printed this mount using Kodak PLA Tough filament with a 0.8 nozzle diameter, strong enough to hold it securely. The...

It´s sized to fit on a CraftBot Flow XL printer, and it leaves space on the sides so that the heads will stay a fair way apart. ... The connections between the squares help removing the single layer print ;-) Try lifting only one edge and you should...

This upgrade encompasses a comprehensive adjustment package tailored specifically to augment current configurations of CraftBot print platforms. ...Key refinements within revised *.stl file revisions revolve around optimized door functionality and...

If you need to recalibrate your printer again later, start with (3) and (4), move your bed looking at the micrometer: adjust the knobs until the measured distance in the four corners is equal to the distance you have noted on your paper; in just a...

I was never fully satisfied with CraftBot's initial thin filament holder, so I created a simple yet elegant gear bearing for smoother rotation. Most of the filament rolls have a 56mm hole diameter and 75/90mm width, so they were my target. I began by...

I built this to perfectly synchronize the two belts in my CraftBot by adjusting them to equal tension. It requires a wooden dowel. The printed parts will grip the middle of the pulleys while you can pull the wooden dowel towards the back of the...

This is a simple and easy to print ball bearing spool holder for Craftbot printers, to be clamped onto their genuine friction type 10.5 mm diameter / 99 mm open length spool holder. It uses two standard 608 (skateboard) ball bearings. ...

The CraftBot shines with exceptional performance as high-quality hardware. However, the stiff yet flimsy little nylon screw used to hold the print bed in place is a noticeable design flaw. One of my prints failed drastically due to the vibrations...

Designed from scratch in FreeCAD, this stock hotend duct is a reimagined take on the Craftbot+ Fan Duct by sepp974. Key improvements include a better fit to fan angles, enhanced airflow through ducts, and a more centralized design around the hotend.

This printable clip is designed for use with a CraftBot printer bed to securely hold the rear edge of a PRINTinZ Printer plate in place. It works best when paired with M3 thumb screws along the front edge. Due to variations in thickness among...

I designed a simple fan duct for the Craftbot, specifically made for Bart's hotend upgrade. I printed it in ABS to add extra safety features, and while PETG should also work well, I wouldn't recommend using PLA without first testing its...

... To address this, I added an updated version with slightly enlarged tolerances (+0.5mm for hole diameters and +0.5mm between top/bottom and middle parts). Print Settings: Printer: Craftbot Rafts: No Supports: No Resolution: 0.2mm Infill: 100%

I added another version with enlarged tolerances (+0,5mm for the diameter of the holes and +0,5mm between the top/bottom and middle part) Print Settings Printer: Craftbot Rafts: NoSupports: No Resolution: 0.2mmInfill: 100% Category: 3D Printer...

... tubes from the scroll wheel assembly. 3. Carefully insert the scroll wheel body into its designated space within the custom mount. 4. ...Reconnect the tubes through precision-cut holes in the mount, then replace the cover plate for a secure fit.

If you're using larger spools of filament for your Craftbot, employ this "over-placed filament guide." It extends the standard feed holder, making it suitable for bigger spools of filament (2-3 Kg), which easily glide into your printer's feed tube.

This object was made in Tinkercad. ...Edit it online https://www.tinkercad.com/things/gn8JJ6U4WnZ

I created a simple test to determine how level my CB build plate is. The design draws inspiration from other available models on Thingiverse, but with some key adjustments to fit the CB's build area. Printed at 0.2mm layer height, this model will...