cr6 se 3d models

The upper corner of my CR6-SE's base sits at 100mm above the Lack below., so That is where I land with my 3mm HDF. It includes a nut insert space and a holder to fix the Slack Lack Catch cones to it. Update 2022/06/18: Fixed an offset issue. ...

Creality CR6-Se strain gauge (level sensor) flexing fix, remove hotend cover, Unload PTFE tube remove 2 long screws from hotend to strain gauge, screw hotend to strain gauge with the hotend covers 2 short screws put printed part, PTFE tube going...

With this design, you can apply the rear fan upgrade, which provides extra cooling, to your CR6 SE printer, as in the Elegoo Neptun 4 Pro. It is easy and simple to use. Apart from the 2D printed parts, an extra 10 m3 nuts and screws and 2 80x80mm...

... can be attached to the existing feet. You only need 2 squash balls, cut them in the middle and put them into the printed foot. The anti-vibration foot can be attached to the printer feet with double-sided tape if necessary. Printed with CR6-SE

... hold it back together. Cracking on the cover of the Creality existing unit usually results in first signs of under extrusion. I now as standard fit this to all my CR6-SE / MAX printers and have had no more extruder cover cracking issues since.

This design is heavily influenced by (not a remix of) two (2) designs: * [CR6-SE Top & bottom mount filament guides by agent9](https://www.thingiverse.com/thing:4590086) * [Creality CR6-SE Filament Wheel Guide Mount by...

instructions: print remove old bracket from spool arm connect new bracket to spool arm place on the top front of your CR6-se this would go well with other prints out there that direct your filament - I didn't need any for my set up, but you might...

Designed for the stock CR6-SE heatsink fan - should fit easily into the 'box' area of Part B, with gap at the top for the fan's cables. Two prongs from Part A fit into the screw holes in the top corners of the fan - push these into place before...

... sobresale y molesta para instalar el conducto de aire. ...con este segundo ventilador el flujo de aire es igual por los dos lados de la boquilla, lo hice de esta forma para no tener que cambiar la carcasa original del hoteng en la creality cr6 se.

Hello, I made this Auto Off Switch for the CR6-SE because i wanted to shut down the printer after he is finished, so the fan wont spin the hole time until i get Home! With this Switch you just disconect the Old Switch, wire the new one up and Mount...

CR6-SE Parts cooling duct. This is a Low profile cooling duct to take a 5015 fan. Part will clear bed clips and bed handle if fitted Duct mounts to the factory hot end shroud in place of the factory cooler fan. Part has tight tolerances...

A Minime cooling duct clone that mounts to the load sensor of the CR6-SE 3d printer. Uses the fan from the stock metal hot end shroud. The duct is designed to mount a Slice Mosquito hot end to the hot end carriage load cell. It is designed to...

The extruder on my CR6 SE was terrible so I replaced it with a Winsinn dual gear extruder from amazon. This however lifted the path of the filament by 10mm and it was no longer in line with the filament run out sensor. This is a 10mm shim to boost...

Built to mount a Wyze cam V2 onto a CR6 SE. May also work with Ender series, depends on the bracket. Mounts to the Z axis bracket on the right side using existing screws/nuts. Holds the camera upside down ~25mm above the level of the print...

This is updated version of Direct Drive with metal extruder on my Creality CR6-SE Printer (based on Michael Bourque Direct Drive). After this update you will see your prints will be much better than with original bowden extruder... NOTE: for this...

---------------------------------- This is an edit of my top rail filament guide to work with the CR6-SE. From the center of the bolts to the center of the wheel is 46mm. Richard Bruckner posted the model for the spool holder in the Creality CR-6...

https://www.paypal.com/paypalme/jensterJ97 This base mount that was designed is used to modify the existing CR6-SE spool holder arm to allow it to mount on the top of the printer. The hardware used to mount the base mount to the top of the...

Hello Everyone, I Designd and Uploaded this Direct Drive Adapter for the Creality CR6-SE because i wanted to print with flexible Filament! The Adapter is Designd to work with the Following Stepper Motor: ...

This is a remix of 3dFreezeMe's awesome extended orbiter mount for the CR6-SE (https://www.thingiverse.com/thing:4818983). The only issue I had with the original is that it limited bed movement slightly in the X axis, where the extruder would hit the...

Designed a camera case and mount for the CR6 SE. This pops right onto the x-axis mount. I put some double-sided tape to secure it on the x-axis. <b>Version 1</b> - My original design. It's kind of close to the nozzle. I can see my prints but it...

Here is my direct drive conversion on the creality CR6 SE using the BMG dual drive extruder. I've been using this for several weeks now and has been working great with no problems. (although there may be small updates to the design if I find...

When I screwed up my stock CR6-SE heatblock (don't over-tighten the nozzle, folks) I realized a replacement was a good 3 week wait. I didn't want to wait that long to continue printing, so decided to cobble together a mount for a V6 setup I had...

I designed this model to attach a universal Bluetooth shutter button to a creality CR 6 SE. ...check out my video for more information https://youtu.be/-YqwcNztbE8

... ... I mixed 2 models of clips to fit my CR-6 SE bowden tube size and the the cable. Those models where too small for the bowden tube or too small for the cable. ... https://www.thingiverse.com/thing:2743992 https://www.thingiverse.com/thing:4631777

A revised clip on Filament guide for the CR-6 SE printer.It's a snug fit, so it may take a slight sanding to get it in.This version includes the printer name and a window to see the filament. ...Many thanks to those who made this before me as they were...

Another "quick-n-dirty" mount for the Orbiter extruder on a Creality CR-6 SE printer. I rotated the extruder to have the motor in front which required raising it up another ~10mm to clear the clips for the cord on the PCB board. Might be less...

A "quick and dirty" mount for the Orbiter extruder on a Creality CR-6 SE. No modification or disassembly required! Just hook the part over the X-carriage V-roller axle and snap the other side down. The Orbiter v1.5 will mount to the holes provided...

These are feet whitch could be snapped into a 40x40mm aluminium-extrusion. They are 40mm high so there is enough space for a fan-upgrade on mainboard and PSU. ...I have printed them out of TPU so they can absorb some of the vibrations.

V1.1 fixed a couple of spacing details.Cleaned up weird voids and artifacts.Made it sit better in the space available.Removed the part cooling duct since I use a different setup.

Remix of a Remix with camera mount. Enable print thin walls for the supports to print Properly. Use supports touching build plate only. It takes 4 M3x12 with nuts and one M3x16 with a nut. ...I used some removable Loctite to keep them from backing off.