cr6 se upgrades 3d models

Did a quick design for adding the older creality style hotend to the CR6. I printed it out to make sure it all fits. Be sure to add a washer in-between where the hotend adapter bolts onto the metal bracket create a gap for flexing. Just wanted to...

... Why I did this mod? I can customize the older style hotend much more than the stock CR6 one because the older ones uses M3 screws instead of M2 screws. I can switch out the hotend when I feed a different size filament. ... no supports needed.

I wanted a simple way to mount my raspberry pi camera with LED ring to my new CR-6 SE at a 45 degree angle. I based my design on this https://www.thingiverse.com/thing:3870779 I decided to use screws and nuts because I didn't want to to move...

This isn't really a remix, but additional plates to cover the wires after installing arkworkvideos excellent Power Supply Cover for the CR-6 SE. I didn't like have any wiring exposed - especially mains. There are two versions - just two flat...

I made an alternate version of this thing https://www.thingiverse.com/thing:4594168 to use a cheap LED strip as a light-bar on my Creality CR-6 SE and needed a way to route the switch. You can see better pictures in my posted make. The improvement in...

I "upgraded" to a PEI bed and it sticks on top of the back of a spare glass bed I have as I wanted to be able to go back to stock if I wanted. I've heard lots of stories of the nozzle jamming into the bed on homing when raising/lowering from the...

This is meant to provide more air to cool the parts, being a free upgrade if you are using other fans and have the original blower laying around. If you want to help, you can make a better conduit. I can't, I'm still not as good as I'd like to be...

I'm not much of a designer (check those damn ducts) but I think I have some good ideas and this is one of them.This is meant to provide more air to cool the parts, being a free upgrade if you are using other fans and have the original blower laying...

Definitely PLA or other low temperature material is NOT recommended as they are resting on the heatsink - but if you've upgraded your fan anyway it's unlikely to get hot enough to melt anything. Mine has been used for printing for hours with no...

Simple adjustable mount for other types of bed surface. ... Needs: 2pcs M5 x 20mm screw and tnut

I took the CR-6 drawer that takman29 created ( https://www.thingiverse.com/thing:4656033 ) and the Z-cover that RICBRU created ( https://www.thingiverse.com/thing:4670030 ) and just simply combined them, then fixed the drawers to fit.The cases fit...

This is a remix from https://www.thingiverse.com/thing:398515 Inspired in the Oiler: https://www.thingiverse.com/thing:2490809

Made a Short Version to save on some material and Print Time.

this is a filament guide that makes a nice transition from sensor to the EZR extruder

a little cap for the 4040 profile after i moved the screen to the other side. ... i changed filament color before the bridge infill, tp make it pop.

i have solved this problem and made the hole a little larger: "For some reason, the slot that receives the spool arm is too small. It's the same size as the spool arm. ...The spool arm will not fit down into the hole."

Provides a lot more airflow so the fan doesn't need to run at 100% all the time (40% is about the power of the original fan). It also saves you ~70g of moving mass, so you can accelerate faster. Combine that with the shorter minimum layer time and...

A simple support to lessen the strain on the printer spool holder with 1KG rolls

Improves extruder strength, for free So there are 6 different sizes so you can choose the tightening you want NH means No-Holes

I brought an E3D hotend off Of Amazon by mistake and rather than sending it back I thought i'd look if there were any adapters around for it. I did find some but they 'just' didn't quite do it for me so I decided to remix a couple of them that I...

I have my filament feeding from a cabinet on top of my printer. This is a simple guide to help reduce tension. I removed the runout sensor and using a knock-off BMG extruder. If you go this route, make sure you turn off run-out detection in Marlin...

Since I don't have enough space on my table, I want my PLA spool to be on top of my printer. ...Super Simple, don't need any screws, compatible with the pool holder piece that comes with the printer.

The Power supply is enclosed with only one inlet and no outlet for hot air to escape. I Tinkered this to fit between the power supply and the cover. You will have to cut a hole in the cover for the exhaust I used glue to install it or you could use...

Remixed from https://www.thingiverse.com/thing:4765453. Only change is a 42mm hole instead of the Creality grill, which should result in a tiny bit more airflow and less noise. It was a bit of work to get the hole aligned perfectly, but i think i...

My Printer sits in a dark area of the studio, and I found it hard to see the SD slot on the front. So, this was born. ...It's a silly item and might not even stay on that great, but hey, it's free and uses hardly any filament at all.

Warning, this is a first draft, so spacers are nedded between the hotend and the shroud, also 6mm pcb standoffs are nedded to mount the original cover back. ... also holes for the 40mm fan are for m3 brass inserts please remix and make this better if...

This is a remix of bertmag's Fallout Endstop. ...I used a skull and crossbones that I found on Thingiverse, sorry but I don't remember the original file or who to give credit to.

Extended version of my other remix, meant to attach a 4020 radial fan mount I remixed (https://www.thingiverse.com/thing:4818990). ... Also made the tab extend out in both directions as it will be even stronger and I do not have the stock shroud...

This a remix of 4594094 filament guide.. https://www.thingiverse.com/thing:4594094 Imported into Solidworks and a made a few additions to keep the cable neat, now you only need to use one those crappy clips. 3 versions. Small, same size...

Use to replace the stock 30mm fan with a (hopefully quieter) 24V 40mm fan. This piece replaces the stock spacer, you can use the existing screws again. You will need 20mm M4 screws to mount the fan. Either tap the holes or the screws should...