cr6 se upgrades 3d models

Creation of a 40mm fan bracket for the Creality CR6-SE (less noise) I haven't tested it, soon ---- Another creation with 30mm OEM fan : https://www.thingiverse.com/thing:4669393

Part cooling fan for the Creality CR6 SE that uses the stock blower flan but directs the airflow closer to the nozzle. ... Version for 40mm quiet fans: https://www.thingiverse.com/thing:4777287

A simpel Z-stop cover for the Creality CR6-SE, stops dust from entering and keep the cable safe. Also looks alot cleaner. Print it with the flat side down. ... Click it into place and enjoy!

Spare parts from another project) Print Settings Printer: Creality CR6-SE Rafts: No Supports: Yes Resolution: 0.16/0.28 Infill: 25% Filament: Mika3d PLA Blue Notes: Using a Creality CR6-SE printer (not available in the drop-down list of printers)...

I opened the clips up, removed the bottom clip, and shifted the wiper to make it line up with the stock hotend on a CR6 SE. I also made the silicone slot deeper to hold the wiper more securely. Remember to add a small piece of silicone (like from...

I opened the clips up, removed the bottom clip, and shifted the wiper to make it line up with the stock hotend on a CR6 SE. I also made the silicone slot deeper to hold the wiper more securely. Remember to add a small piece of silicone (like from a...

instructions: print remove old bracket from spool arm connect new bracket to spool arm place on the top front of your CR6-se this would go well with other prints out there that direct your filament - I didn't need any for my set up, but you might...

A simple holder for the Raspberry Pi Cam on the Creality CR6-SE. ... Screws you need: To assemble the holder: 2 x M3x18mm 1 x M3x10mm 3 x M3 Nuts To mount on the V-Profile: 2 x M4x10mm 2 x M4 drop-in-t-nuts To fix the cam on the holder: Original...

A simple holder for the Yi-Home Cam on the Creality CR6-SE. ... Screws you need: To assemble the holder: 2 x M3x18mm 1 x M3x10mm 3 x M3 Nuts To mount on the V-Profile: 2 x M4x10mm 2 x M4 drop-in-t-nuts

While the general design of the stock cooling shroud is adequate I needed a way to improve accessibility to the hotend on the CR6-SE, hence this 'thing'! Prints with minimal supports (recommended), this is a fairly lightweight design yet very...

A simple holder for the Yi-Home Cam on the Creality CR6-SE. ... Screws you need: To assemble the holder: 2 x M3x18mm 1 x M3x10mm 3 x M3 Nuts To mount on the V-Profile: 2 x M4x10mm 2 x M4 drop-in-t-nuts

i moved my spool for my cr6-se to a top mount and then to a side mount. i was using zip ties but my prints kept getting tangled because the side mount was easy for the filament spool to fall from. i designed this clip to print quick and easy. ... ...

Replacement bracket/housing for the top z-axis bearing on the CR6-SE. Not sure what the dimensions are for other Creality printer gantries, but it might work for others as well. Both of my stock housings broke (flimsy plastic), so I made this. Use as...

The spool holder that came with my CR6 se was just a little too wide to fit into one of my filament spools. I made this thinner one in Freecad, which still fits into the arm that comes with the printer. ...The body of it has a diameter of 26mm and the...

Creation of a fan bracket for the Creality CR6-SE 7x lighter than the original Creality case ----- 04/12/2020 v2 Take into account mounting variations possible by modifying the fixing holes to be able to adjust the horizontality of the cooler ----...

A simple holder for the Raspberry Pi Cam on the Creality CR6-SE. ... Screws you need: To assemble the holder: 2 x M3x18mm 1 x M3x10mm 3 x M3 Nuts To mount on the V-Profile: 2 x M4x10mm 2 x M4 drop-in-t-nuts To fix the cam on the holder: ...

The upper corner of my CR6-SE's base sits at 100mm above the Lack below., so That is where I land with my 3mm HDF. It includes a nut insert space and a holder to fix the Slack Lack Catch cones to it. Update 2022/06/18: Fixed an offset issue. ...

... can be attached to the existing feet. You only need 2 squash balls, cut them in the middle and put them into the printed foot. The anti-vibration foot can be attached to the printer feet with double-sided tape if necessary. Printed with CR6-SE

... hold it back together. Cracking on the cover of the Creality existing unit usually results in first signs of under extrusion. I now as standard fit this to all my CR6-SE / MAX printers and have had no more extruder cover cracking issues since.

Part cooling fan for the Creality CR6 SE that uses the stock blower flan but directs the airflow closer to the nozzle. ...Version for 40mm quiet fans: https://www.thingiverse.com/thing:4777287 Print Settings Printer Brand: Creality Printer: Ender 3...

Creality CR6-Se strain gauge (level sensor) flexing fix, remove hotend cover, Unload PTFE tube remove 2 long screws from hotend to strain gauge, screw hotend to strain gauge with the hotend covers 2 short screws put printed part, PTFE tube going...

This design is heavily influenced by (not a remix of) two (2) designs: * [CR6-SE Top & bottom mount filament guides by agent9](https://www.thingiverse.com/thing:4590086) * [Creality CR6-SE Filament Wheel Guide Mount by...

Designed for the stock CR6-SE heatsink fan - should fit easily into the 'box' area of Part B, with gap at the top for the fan's cables. Two prongs from Part A fit into the screw holes in the top corners of the fan - push these into place before...

Richard Bruckner posted the model for the spool holder in the Creality CR-6 SE/CR-6 MAX Official User Group; RB_CR6_SE_Top_Mount_Spool_Holder.stl. I am not taking credit for this model. I've included a version here where I made the mounting holes...

... sobresale y molesta para instalar el conducto de aire. ...con este segundo ventilador el flujo de aire es igual por los dos lados de la boquilla, lo hice de esta forma para no tener que cambiar la carcasa original del hoteng en la creality cr6 se.

Hello, I made this Auto Off Switch for the CR6-SE because i wanted to shut down the printer after he is finished, so the fan wont spin the hole time until i get Home! With this Switch you just disconect the Old Switch, wire the new one up and Mount...

Built to mount a Wyze cam V2 onto a CR6 SE. May also work with Ender series, depends on the bracket. Mounts to the Z axis bracket on the right side using existing screws/nuts. Holds the camera upside down ~25mm above the level of the print...

The extruder on my CR6 SE was terrible so I replaced it with a Winsinn dual gear extruder from amazon. This however lifted the path of the filament by 10mm and it was no longer in line with the filament run out sensor. This is a 10mm shim to boost...

This is updated version of Direct Drive with metal extruder on my Creality CR6-SE Printer (based on Michael Bourque Direct Drive). After this update you will see your prints will be much better than with original bowden extruder... NOTE: for this...

CR6-SE Parts cooling duct. This is a Low profile cooling duct to take a 5015 fan. Part will clear bed clips and bed handle if fitted Duct mounts to the factory hot end shroud in place of the factory cooler fan. Part has tight tolerances...