cr6 se upgrades 3d models

Made a spool resized for the 54mm holes in certain spools. I'll have more version coming for the larger 73mm hole spools as well. ... The ring fits snugly over the end to keep the spool from falling off.

This setup is a Remix I made from scratch to mount a Sunlu dryer box up top and a slip on filament guide The Sunlu mount is made to be a tight fit Depending on how dialed in your settings are you may have to sand the outsides of the bushing to...

My first remix ! ;) https://www.thingiverse.com/thing:4654645 The mounting design on the original fits perfectly on the head But I didn't like the orientation of the clip, and I kept breaking it trying to fit the ribbon inside. ... I found...

I needed a spool-holder that does not take up additional desk-space. So I adapted the Ender 3 metal spoolholder. When putting the filament on top you have to also have some kind of guide to feed at an relaxed angle. The guide is made out of two parts...

I've been developing this adapter off and on since the spiring of this year (2021) after having gotten tired of using the factory hotend. Clogging was becoming constant despite all attempts to thwart it. Having replaced the entire hotend assembly...

Hi. Here is a quick mount to re position the filament run out sensor, to point towards the back, this bracket mounts to original position, then mount the FROS to that. Will need 2 extra m3 x 20 and 2 m3 x 10 countersunk bolts. I use this in...

Simple but effective led holder, i use them with SMD2835 Light Strips with double sided tape. may fit other brand, as it use only one track to hold! ... Include both side, printable in less than 1 hour

simple rack for 5 nozzle fixed on profile 40*40

i took this file (https://www.thingiverse.com/thing:4922950/files) and redid it cus it was missing some parts wehen i loaded it. so i redid it to fit my measuring tape on the side since i moved my spool to the top of the printer. ... 0.28LH-...

Added the cable guide ('Flatcable_holder.stl' (designed by @Sebazzz) to the Angled Orbiter Mount by dryphi. Based on latest v2.5 revision which is tested/confirmed working. I did not print this remix yet for testing, still have the original...

Hello Everyone ! This adapter fully fit with orginal parts. You can use with orginal filament sensor and orginal sensor and engine cables no need add or anythingelse. This parts advantages are less printing time 2 Hour 30 Minute ! and...

Onepiece print for the hotend, to connect a 50mm fan to it.

This is a remix of my very popular [BRDD](https://www.thingiverse.com/thing:4837410) (Bourque/Rowland Direct Drive) system. This improved design solves a problem that some have reported where the bracket melts due to the stepper overheating. While...

See my make for more photos. This thing was inspired by this thing https://www.thingiverse.com/thing:4688169 but I made it all from scratch and it's quite different. It's only 38mm by 28mm as that's the only space I had behind this drawer for...

Added a hole in the case for the RPi camera Remix by putting together the following two: Case from https://www.thingiverse.com/thing:4611286 Hole from https://www.thingiverse.com/thing:3026059

This is a remix of the remix! I just made it completely flat on the bottom in solidworks and I also made the outside and top of the ring flat too. It should be much stronger now. This is a good base for modification as the original mesh was VERY hard...

There are 2 different drawers for under the screen. 1 is with a USB extension plugged into the screen and 1 is without. ... Then there is a right side under the bed and a left side under the bed.

thanks to Paroni for the model. I added some walls left and right so it would cover up the cables for a cleaner look. Uploaded three versions: one is fully closed the other has a honeycomb opening on the left wall, the last one has a Honeycomb...

These feet will dampen the vibrations, raise the height and allow you to pull the printer forward (if you need to, mine is on a cupboard that wasn't quite deep enough). Print them in TPU and thye work just great! ... I used 40% infill density.

This is a remix of the OriginalSpeedrive V1- Directdrive Mount with some changes and some optimizations to fit perfectly for CR-6. Installed in my Cr-6 Max and works great. Please make sure the Pinch-Roller Mounting holes have exactly 8mm in...

Material need: - 5mm led diode - resistor (220ohm) - heat shrink - plastic led holder for 5mm led - two plastic ties 100x2,5mm (wired LEDs already exist on the market) --- reused original screws and cable with jst connector ---

This is a laser holder console to https://www.thingiverse.com/thing:4701896 direct drive extruder.

Thanks to MB_AUZ for great concept: https://www.thingiverse.com/thing:4653730 I have just added a bit of height and now the cables are straight up, plus the bowden support is not clip-on but full through-hole. ... Great initial design, though -...

Danger: Currently, my ABL is messed up. Maybe wait for next version, if you do not want to use a file. This remix of mine comes with a complete source file, so you can make your own version with your favourite type of insert or whatever. Main...

I've tried adding LEDs to a few different fan ducts that go around the hot end and blow air down instead of the stock system and they've all worked really poorly - but I still didn't want the stock blue LED. I came up with this small adapter that...

i needed one

Here is an adapter to add a closedLoop module on the Y axis without being disturbed by the bed. This is the MKS Servo42C model which is more compact than the one from Bigtreetech. For this mod you will need to reverse the pulley on the rotor and...

I found the original version of this had two issues with the strain gauge and therefore the automatic bed levelling: 1) Not enough clearance around the Bowden connector 2) Not enough clearance around the Bowden tube to allow it to move freely ...

I like the look of the blue LED, but it's rubbish to actually see the print. A fan duct seemed the ideal starting point for adding more! The original fan duct design from Kroffty is amazing. I just added the ability to put some cheap LED lights from...

I really like the mount I remixed, the only thing was I wanted some adjustment within the mount. ...I was able to achieve the required adjustment by incorporating a GoPro style mounting system.