cr6 se filament sensor 3d models

a little cap for the 4040 profile after i moved the screen to the other side. ... i changed filament color before the bridge infill, tp make it pop.

My Printer sits in a dark area of the studio, and I found it hard to see the SD slot on the front. ...So, this was born. It's a silly item and might not even stay on that great, but hey, it's free and uses hardly any filament at all.

My Printer sits in a dark area of the studio, and I found it hard to see the SD slot on the front. ...So, this was born. It's a silly item and might not even stay on that great, but hey, it's free and uses hardly any filament at all.

A flat spool holder making use of the original spool holder arm using a PTFE tube (bowden tube) with 4 mm OD as a sliding surface for the filament spool. This is heavily inspired by the spool holder solutions for the line of Voron printers over at <a...

There was also no topology optimization done to find the best and least amount of filament use due to restrictions of fusion 360. Since both parts are in one fusion file the pin needs to be re-oriented in the slicer software of your choice. ... ...

I strengthened the arm, pushed it out a bit, and added an extension that can push against the filament sensor box to keep the wheel from hitting it. ... **The rest of the pieces from the original are required, this is just a modification of the arm to...

10-27-20 Updated all models I had a problem with some of them being lifted from the build table. I removed the...

The Stock Filament holder on My CR6-Max was leaning quite a bit, So I made this to level it up. Probably overkill, but it works great, LOL. ...Just put the small Block under the stock holder, and the Large brace slides into the hole in the stock holder.

Creality CR-6 SE filament sensor riser plate for WINSIN dual gear extruder. ... The stock screws are too short, you will need to use 2x M3 25mm or longer screws to hold the mount the sensor.

I upgraded my CR6-SE extruder to a cheap dual-gear one from Amazon as the bog-standard plastic one was awful and I had no idea if if was filling up with rubbish or not and it was impossible to adjust! Unfortunately, that meant the filament sensor...

When the Micro Swiss Bowden Dual Gear Extruder is mounted on the CR-6 SE, the position of the Filament Runout Sensor no longer fits. With this adapter piece, the position of the filament runout sensor is shifted slightly so that everything fits...

Case for Creality CR6-SE with 40mm fan duct remixed from https://www.thingiverse.com/thing:4714322 Print Settings Printer brand: Creality Printer: CR6-se Rafts: No Supports: Yes Resolution: 0.20 Infill: 25% Filament brand: Overture Filament color:...

When the Micro Swiss Bowden Dual Gear Extruder is mounted on the CR-6 SE, the position of the Filament Runout Sensor no longer fits. With this adapter piece, the position of the filament runout sensor is shifted slightly so that everything fits...

Like the title says - a filament sensor riser plate for Creality CR-6 SE for dual gear extruders with integrated cable holder. Helps with the cable rubbing on other parts and getting in the way of the filament. There are few brands of those...

It is the required part to use the filament sensor when you replace the extruder used by Creality CR-6 SE with BMG Extruder V2.0. Since I could not find such a piece design, I designed this piece myself. I hope it works for you too. With this...

... with two m3 screw holes. I also remixed a gentler filament inlet for the filament runout sensor from L30Aero's design. You will need 2 m3x30mm screws to attach this to the stock mount points. ... Printed at 0.2mm layer height with 20% infill.

... with two m3 screw holes. I also remixed a gentler filament inlet for the filament runout sensor from L30Aero's design. You will need 2 m3x30mm screws to attach this to the stock mount points. ... Printed at 0.2mm layer height with 20% infill.

Re-mix of a CR6-SE ribbon cable guide to personalize it up somewhat

CR6 SE Cable clip Guide with bowden Tube holder&nbsp;

My design of a USB

Soportes cadeneta carro

Petg 40% 0.20

This bracket has been specifically designed to mount a usb powered led light . ...The brand is Qooltek and can be found on Amazon.

Remixed from: www.thingiverse.com/thing:2759439 www.thingiverse.com/thing:4654645 Two options for mounting the shroud, one with the cable holder or with the bracket. Cable holer and the bracket has hole for M3 inserts, but not necessary. The...

This is a remix from https://www.thingiverse.com/thing:398515

This USB storage can clip into the side of the printer and can up to hold 6 USBs, 4 SD cards and 2 Micro SD cards

These are feet whitch could be snapped into a 40x40mm aluminium-extrusion. They are 40mm high so there is enough space for a fan-upgrade on mainboard and PSU. ...I have printed them out of TPU so they can absorb some of the vibrations.

Did get heat creep so i designed a fanduct REMEMBER TO DO A PID TUNE AFTER

Remixed from https://www.thingiverse.com/thing:4634825 I used the printer clip part and added a part to hold an aluminium led channel to the to of the printer. ... This makes for good light for my Tapo C100 camera.

This is a mock-up of the CR-X hotend assy.edit: 02-27-2021updated issues of holes and components not aligning properly from incorrect measurements on my part. ...I believe this now closely resembles the actual assembly.