cr6 se fan 3d models
148297 3d models found related to cr6 se fan.
thingiverse
Print 2 of the fan spacers one for the power supply and one for the board cooler. I also had a spare 30mm fan and installed it on the side of the cover to exhaust the hot air. There is a spare fan header on the board to plug it in. ...You will have to...
thingiverse
... to lower the voltage of the motherboard which is 24V to the fan voltage. I enlarged the two mounting fan holes with a 6.5mm drill. This mod is the same thickness as CR6-SE (Kit) Power Supply Fan Adapter : https://www.thingiverse.com/thing:4685262
thingiverse
I also put a small silicone rubber washer under the head of each of the two fan mounting screws, just to hedge against those screws possibly carrying fan vibration to the finned body of the extruder. NOTE: I only print PLA, PETG and TPU on my...
thingiverse
Designed this fan duct because I didn't like the gap causing air to flow down on part. The part fits very nicely on to heatsink and I have seen a difference. Also working on a way to isolate air from heatsink hitting the mounting plate and ejecting...
thingiverse
While the general design of the stock cooling shroud is adequate I needed a way to improve accessibility to the hotend on the CR6-SE, hence this 'thing'! Prints with minimal supports (recommended), this is a fairly lightweight design yet very...
prusaprinters
With this design, you can apply the rear fan upgrade, which provides extra cooling, to your CR6 SE printer, as in the Elegoo Neptun 4 Pro. It is easy and simple to use. Apart from the 2D printed parts, an extra 10 m3 nuts and screws and 2 80x80mm...
thingiverse
This is a fan duct for Creality CR-6 SE that uses a 40x20mm blower fan to supply filament cooling to the hotend. Lots of good airflow. I think it may also fit the MAX. Print with front facing down and with supports only touching buildplate. .8mm...
thingiverse
...fits the 60x60 fan (Noiseblocker BlackSilentFan XR2 60x60x25mm (12v...needs a buck converter) NOTE: the fan case has two sides with slightly larger side tabs..for better gluing. ... also, a good low profile companion power supply cover is my...
thingiverse
4020 fan adapter that fits inside the original CR6 hotend cover. Provides a lot more airflow so the fan doesn't need to run at 100% all the time (40% is about the power of the original fan). It is required that you remove the upper part of the...
thingiverse
... adapter: 6x M3x8mm. ... This mod must be used with CR6-SE Power Supply Noctua NF-A6x25 Fan Adapter : https://www.thingiverse.com/thing:4685799 This mod is the same thickness as CR6-SE Motherboard Fan adapter : https://www.thingiverse.com/thing:4685267
thingiverse
Provides a lot more airflow so the fan doesn't need to run at 100% all the time (40% is about the power of the original fan). It also saves you ~70g of moving mass, so you can accelerate faster. Combine that with the shorter minimum layer time and...
cults3d
i used noctua A4x10 fans: https://smile.amazon.de/Noctua-NF-A4x10-FLX-40mm-Lüfter/dp/B009NQLT0M/ref=sr_1_3?__mk_de_DE=ÅMÅŽÕÑ&crid=35YO3YLY2JYJ9&keywords=noctua+a4x10&qid=1639938021&sprefix=noctua+a%2Caps%2C199&sr=8-3 and the voltage boards with...
thingiverse
... draft, so spacers are nedded between the hotend and the shroud, also 6mm pcb standoffs are nedded to mount the original cover back. ... also holes for the 40mm fan are for m3 brass inserts please remix and make this better if you have the urge to do so
thingiverse
Use to replace the stock 30mm fan with a (hopefully quieter) 24V 40mm fan. This piece replaces the stock spacer, you can use the existing screws again. You will need 20mm M4 screws to mount the fan. Either tap the holes or the screws should self...
thingiverse
UPDATE: I've tried a few versions of these fan ducts - mainly with the plan of adding lights around the outside of them - but mostly the cooling has been the same or worse than stock. My new plan is using a 4020 fan and the stock cooling duct! ...
thingiverse
Creation of a 40mm fan bracket for the Creality CR6-SE (less noise) I haven't tested it, soon ---- Another creation with 30mm OEM fan : https://www.thingiverse.com/thing:4669393
thingiverse
Creation of a fan bracket for the Creality CR6-SE 7x lighter than the original Creality case ----- 04/12/2020 v2 Take into account mounting variations possible by modifying the fixing holes to be able to adjust the horizontality of the cooler ----...
thingiverse
Part cooling fan for the Creality CR6 SE that uses the stock blower flan but directs the airflow closer to the nozzle. ... Version for 40mm quiet fans: https://www.thingiverse.com/thing:4777287
prusaprinters
Part cooling fan for the Creality CR6 SE that uses the stock blower flan but directs the airflow closer to the nozzle. ...Version for 40mm quiet fans: https://www.thingiverse.com/thing:4777287 Print Settings Printer Brand: Creality Printer: Ender 3...
thingiverse
Case for Creality CR6-SE with 40mm fan duct remixed from https://www.thingiverse.com/thing:4714322 Print Settings Printer brand: Creality Printer: CR6-se Rafts: No Supports: Yes Resolution: 0.20 Infill: 25% Filament brand: Overture Filament color:...
thingiverse
added a diode to regulator not feeding back the fan circuit (they share same ground so put on red cable) End result and tests: @240c hotend and 110c bed temp and 23c room temp under constant 180Watts of average load, fan never kick in for full power...
thingiverse
This is a remix of: https://www.thingiverse.com/thing:4763254 This is a fan shroud duct and cover the CR-6 SE. It uses a 40x10mm 24v fan and will direct cool air all around the nozzle. Requires a 40x10mm or 40x20mm 24v fan. Print front facing...
thingiverse
Remixed from https://www.thingiverse.com/thing:4765453. Only change is a 42mm hole instead of the Creality grill, which should result in a tiny bit more airflow and less noise. It was a bit of work to get the hole aligned perfectly, but i think i...
thingiverse
This mod must be used with CR6-SE (Kit) Power Supply Fan Adapter : https://www.thingiverse.com/thing:4685262 Adapter to replace the **original MeanWell power supply fan** of the CR6-SE with a **Noctua NF-A6x25 fan**. ... **This mod requires a disc...
cults3d
... ... Improved fan duct can be found at https://www.thingiverse.com/thing:4763949/files I used fans bought from https://arcto3d.se/guides/installing-our-silent-fan-kit-on-creality-cr-6-se/ Will upload photos once I have my printer upgrades finished.
thingiverse
... ... Improved fan duct can be found at https://www.thingiverse.com/thing:4763949/files I used fans bought from https://arcto3d.se/guides/installing-our-silent-fan-kit-on-creality-cr-6-se/ Will upload photos once I have my printer upgrades finished.
thingiverse
I printed the original thing this is remixed from in PETG, so it looks pretty blobby etc, but it's strong stuff - however, I'm using it with a 4020 fan instead of a 4010 fan and within about an hour the weight had made it start to droop and it was...
thingiverse
Part cooling fan for the Creality CR6 SE that uses the stock blower flan but directs the airflow closer to the nozzle. Uses 40mm, quieter fans It can wobble a little bit so I might try the mount in PLA+ and keep the duct in PETG for the heat. At the...