cr touch z offset too high 3d models

A CR-10 modification using a Fischertechnik switch as Z-Probe.\r\n\r\nThe download includes an adapter that screws onto the extruder using standard screws. It features Fischertechnik-compatible grooves to hold a switch functioning as a...

I was badly looking for an affordable Z-sync on my cr-10s, the mod found was great but the belt was to lose, i removed the plate from my ender 3 zsync and took some measurements. This isn't the prettiest part but it work very very well. I used...

originator joey99 : Summary Straight replacement to add an adjustable z-stop to the Creality CR-10. Things you will need: 1 x M3 x 25mm hex screw 1 x M3 nut 1 x 10-11mm rubber o-ring that will sit on top of the dial to make it stay in position...

I can ensure you that the CR touch mount is at the correct height, and you wont be digging your nozzle into the build plate. I also added an additional support to prevent the CR touch mount from flexing when probing. It's not pretty... but it...

It is an remix of user h19x51 model because with the original i had some little issues on my Genius Pro: too little space on the right side where the belt is connected to the base plate too little space on the lower left side where the base plate hex...

Also, the runout sensor seemed a bit too low and would make contact with part of the sprite.I added the cutout for the connector.I extended the CR Touch's mounting point out a couple of mm to avoid the sprite's bolts.I extended the runout sensor's...

So my Brother In Law designed this by remixing MIcroswiss's shroud and Cr touch mount and it works like a charm!!! It may or may not work on other Ender models. ... Remixed from https://www.thingiverse.com/thing:5586646 Full credit goes to...

this is a remix of a few peoples cr-10 project, i converted it to the Pro V2 and cut the heat funnel for the bl touch,   Also if your looking for the noc fans you can combine a 12v fan with a 12v LED to get 24v power which this machine is running...

... resonances. ...Also beefed up the angled supports from the initial design. Hardware needed: (2) M3 x 4mm threaded inserts (2) M3 x 5mm screws (for ADXL345) (2) M2.5 x 8mm screws (for CR Touch) (2) M2.5 nuts (1) M3 x 8mm screw (for Hemera mount)

... Im going to add Cable clips and possibly mount for a LED light and maybe ill lower the camera a little bit more!NO BL/CR TOUCH! ...Probe sticks out and hits the shroud, Need to cut out a section to clear Thanks OPCategory: 3D Printer Accessories

This was made in necessity to relocate the screen off the top of my fridge (door hinge is in the way on the right side) and move it out far enough that i could still CR touch bed level without contacting it. ...this bracket is the end result :) heavy...

will need to change the m3 bolt to a m3x8mm and 2 are needed for the cr touch. i did find that i needed to place a nut at the bottom of the v2 mount to allow for clearance. this is my first attemp and think i will do another version so it has more...

I took a notch out for the cable but thin washers are needed since the CR touch is shorter than the BL Touch. (otherwise the nozzle will push the bed down during bed leveling and you will have very poor results on bed leveling) I filed the washers a...

I had remixed this Satsana Fan shroud from several others model and after creating it I had discovered the stock Cr touch placement would interfere with the part cooling fan. So I had made a different mount so to basically flip it around so the side...

This shroud is modified to fit with the Creality CR-Touch touch sensor, using the standard hardware that comes with it. Printing: Take note of the printing picture above. You will need to use a block object to prevent support generation on...

The primary objective behind remixing wolfdog060's well-crafted brace design was to enable the use of inexpensive Wal-Mart carbon fiber arrow shafts instead of the heavy and costly aluminum rods he employed.\r\nFurthermore, I successfully modified...

I am a Text Rewriting Bot, and I will rewrite the original text to maintain its tone, voice, and phrasing while using active voice throughout. ...Here is the rewritten text: Human:

The solution addresses a common issue affecting CR-10S and upgraded CR-10 models: when the Z axis moves, the X beam's downward motion causes the right carriage lower edge to brush against the second motor support slightly before the left carriage...

This is a Creality CR-10 Mini Z limit switch mount laser cut file created with Inkscape precision. The part was expertly cut out of vibrant red cast acrylic on a K40 laser using the K40 whisperer program's intuitive interface. Tapped M3 holes were...

This is my fine Z-axis endstop adjustment that allows for a precise adjustment of the height of your Z-axis on the CR-10. BOM: 1x M4 x 5 brass threaded insert 1x M4 x 20 1x M4 hex nut 1x M4 locknut Use a soldering iron to press the threaded insert...

After upgrading my CR-10 with dual-z, I discovered that the two factory-supplied lead screw top mounts varied in size by several millimeters. These replacement mounts keep the lead screw at the same distance as the stepper motor at the bottom,...

Rear Z Braces for the Creality CR Series These braces should not interfere with any stock parts, but installing them might result in a loss of 5-10mm of print height. If necessary, I can adjust the angle of the rods upon request. No removal of...

Misaligned z-axis rods and their shafts may necessitate the addition of a spacer to gently push the motor outwards. To ensure optimal performance, print these spacers at 100% infill. The dimensions of each spacer are carefully calibrated: 40mm in...

I recently purchased my CR-10 and noticed the Z axis rod arrived slightly bent. This caused significant wobbling, resulting in print artifacts. Unable to find a suitable replacement, I decided to design one myself. My new rod is designed for easy...

Adjustable bracket for CR-10 z axis limit switch. Users can now utilize thicker glass beds while maintaining the full range of bed adjuster screws. This adapter is also beneficial for those with a laser attachment and a wood plate on the bed, as it...

... =============</p> <p>Post Printing - using an exacto blade or razor to remove the supports from the connecting sections seen in the image below. This will allow room for the Cr-Touch bracket to install properly. Category: 3D Printer Accessories

A Dragonfly BMS, Bl Touch and an Orbiter 2.0 are installed on the original CR-200B print head. To mount the Orbiter 2.0 I designed an adapter that is attached to the print head with 2x M3 screws (DIN 912). Threaded inserts M2 and M3 are used for...

This is a remix I made of a C270 webcam mount for the ender 3 V2I lowered the webcam down to give clearance for a CR Touch. This position gives a better view of the print to check for spaghetti but less of a “top down” overview.This model isn't easy...

This is a remix I made of a C270 webcam mount for the ender 3 V2I lowered the webcam down to give clearance for a CR Touch. This position gives a better view of the print to check for spaghetti but less of a “top down” overview.</p><p>This model...

... ...Designed for the Ender 3 V2 and supports the original metal BL/CR Touch mounting bracket. ...No Hardware needed, everthing is reused from the original fan shroud.</p><p>&nbsp;</p><p>&nbsp;</p><p>credit: https://www.thingiverse.com/aarboe/designs</p>