cr touch z offset too high 3d models

Replacement part for the CR-10 Z rod top brace. One variant holds the stock bearing. Another variant is bearing-free, in case the bearing is too tight. Another variant uses a standard 608zz or 608rs bearing. Two M3 x 14 screws are used to attach the...

I use a CR Touch rather than a BL Touch and the EVA 3.0 BL Touch is no longer compatible. I couldn't find a CR Touch connector for EVA 3.0 that was sensible/worked so I've made this one. This one fits easily where the standard EVA 3.0 BL Touch...

i really like Satsana remix by Nazar78 but i got a CR Touch and it just didnt have the notch for it while there is other Satsana with cr none still had all the other parts that Nazar78 did with the fan covers this is the link to get to Nazar78 model...

Remixed the original 5015 fan duct and slimmed the left duct down to make room for the CR Touch Also added a slot for an M3 nut to utilize the rear mounting hole from the original duct

Nozzle upgrade to improve cooling of builds. ...Made for ender 3 with cr touch/Ender 3 pro Check out the original design for the second part to this upgrade.

I used tinkercad and a cadgrab model to make this model compatible with the cr touch without decreasing the build volume. ...Read the original's desc for more details.

It is a mounting part for CR-Touch used in combination with Briss fang v4.3. ... https://cults3d.com/en/3d-model/tool/ender3-v2-dual-40mm-fan-hot-end-duct-fang

I used tinkercad and a cadgrab model to make this model compatible with the cr touch without decreasing the build volume. ...Read the original's desc for more details.

It is a mounting part for CR-Touch used in combination with Briss fang v4.3. ... https://cults3d.com/en/3d-model/tool/ender3-v2-dual-40mm-fan-hot-end-duct-fang

I made this replacement when my Z leveller on my Anycubic Photon Mono X broke - There is a Z offset spacer as well in case you need it to add height when installing a magnetic plate for your print bed or if you have a Z offset problem on your printer...

I purchased the Creality Official Ender 3 Direct Drive Upgrade Kit, Comes with 42-40 Stepper Motor Hotend Kit, 1.75mm Direct Drive Extruder Fan and Cables and wanted to use the Satsana shroud with stock CR-Touch mounting. I remixed this to fit on...

A remix of MathiasM74's ADXL345 mounting bracket made to support the increased thickness of the Ender X-axis gantry from the CR Touch probe. Used to calibrate input shaping in Klipper. Snug fit on my Ender 3 Pro + CR Touch gantry. Using the screw...

... (thanks to them for providing this latter one). Here is the link to the carriage provided by Hotends.fr for the CR-10, just enlarge the holes a bit to fit it on the CR-10 S Pro: https://www.hotends.fr/en/downloads/70-smart-support-aioevo.html

I'm happy to help! ...Here's a rewritten version of your text: Support motor for Z axis \r\n\r\nCreate a mirrored print for both sides

... is the perfect upgrade for anyone looking to take their 3D printing game to the next level. Whether you're a seasoned pro or just starting out, this Tornado Double Z Rod Plate CR-10 is sure to impress with its incredible performance and versatility.

If you're making the Swissburner (Voron Afterburner mod for Ender 3 style printers, not V2, with Microswiss all-metal hotend) but still want to use the metal bracket included with your CR-touch, or reality bought BL-touch. ...THIS is your part.Fits with...

The existing BL Touch mount for the Ender 6 BIQU H2 carriage I'm using didn't fit my CR Touch, and was also pretty difficult to install. So I designed this simple 35mm fan mount.</p><p>It's not just limited to use with the BIQU H2, although that is...

Just take BL Touch mount and mix it with "CR-10 / Ender Hotend Cover For Stock Fans" in Meshmixer, then line up the holes. Do a plane cut to remove the parts from the BL touch mount that interfere with the hotend cover internals. Luckyman said he'll...

CR-10S Pro Dual Z Sync You need: 2x flange bearings KFL08 1x GT2 timing belt 760 mm 380T 6 mm wide 2x GT2 gear pulley 20T bore Ø 8 mm The original T nut Remove the flange bearing KFL08 from the flange by simply turning it 90 °. ... Or with the ball...

Ethan really needs your support, and his goal is to reach 500 subscribers: http://goo.gl/ELT7ii I added M3 threads to [mars_null](https://www.thingiverse.com/mars_null/about)'s [Adjustable CR-10 Z endstop](https://www.thingiverse.com/thing:2349068),...

I also wanted it to sit in line with the Y-Axis of the printer nozzle.Offsets for the prove are X: 39 and Y: -1 (Z offset should be the same as the stock mount location)I'll link my Noctua 40x40 fan mounts as I finish them as well.&nbsp;Additional...

Z-Level EndStop.gcode: "M117 Homing Machine G21 G90 G28 X0 Y0 ;Position 1 Bed Screw axis 1 (not the same on each CR-10) G1 X31 Y25 F3600 G28 Z0 M0 Level Z End-Stop G1 Z2.0 F4200 ;move nozzle up G28 Z0;move Z to min endstops M0 Level Z End-Stop G1...

This is a bracket for mounting a Wham Bam Mutant to a CR-10 3D printer and a bracket to mount a touch sensor so that it is not attached to the mobile plate. ... Allow the same touch sensor to be used with multiple MUTANT mobile plates.

I trimmed the front of this cover down so it will clear a BL Touch or a CR Touch when it auto homes. I also created a wire slot on the back rather than a hole out the side like the original. ...This is for ease of installation and I also feel like it...

The CR Touch connector is in a different location than the BL Touch as well as sticks out further to the left. This brings in the mount a few mm as well as relocates the connector hole. ...The cable retainer is optional.

This is a straightforward Z screw position indicator designed specifically for CR-10 (or CR-10s) machines. It's probable that it will fit other models as well if they utilize identical leadscrew sizes. I've successfully printed four of these...

... its already heated and scratch the plate. In order to accommodate the differing heights of the glass bed and mat, I designed a simple, slotted Z-limit-switch plate that attaches to the side of the printer that allows the user to adjust the height.

**OR G-code** (Download .gcode) **Note:** Your stepper driver must have a good current value, too high can cause problems at this step. 200mAh for each motor is OK. ... If you use TMC with communication, you can use: #define TMC_Z_CALIBRATION to have...

I wasn't quite satisfied with the design of any CR-10 Z-braces I'd seen, and I had some carbon fiber tubes left over from other projects, so I decided to model some little mounting brackets in Blender and put them to use. You will need: M5 tap, to...

It's designed to tension the belt in a [CR-10S Pro Dual Z Timing Belt Sync](https://www.thingiverse.com/thing:3387741) setup, either as is or with the [CR-10S Pro Z Sync Stepper Lift Mounts](https://www.thingiverse.com/thing:3431219). It utilizes a...