cr touch vs bl touch 3d models

I created this part because I couldn't find any BL Touch support system for AlfawiseU20 or CR10. Two sliding parts. This way the HotEnd remains accessible. Printing made in ABS (more heat resistance) then smoothing with Acetone (a little bit more...

I get fed up of having to reset the Z offset each time i remove the fan shroud for cleaning/maintenance etc so i cut off the lugs that share the same screws so the BL Touch stays mounted when the fans are removed. ... The M5 bolt that sticks through...

This is a custom mount designed specifically for the BL-Touch on the JG Aurora A5 3D printer. It's been expertly integrated with a cooler enclosure to enhance performance and stability. When installing, be sure to replace the original screws with...

Two versions of the center mount for the BL Touch + ADXL343 or ADXL345 sensor. Both sensor versions have different screw fitting. One is screwed directly into the plastic, this is only suitable if you plan to keep the sensor on the print head. ...I...

***[DEPRECITATED]*** ___updated design available here:___ https://www.thingiverse.com/thing:5389810 Remix of the Manta MK2 BL Touch Central Mount with added holes to fit M3x5.7mm heat set inserts for mounting an ADXL345 IMU. Using this sensor, any...

I've taken a popular BL Touch mount design from Thingiverse, specifically this one: https://www.thingiverse.com/thing:3148733. The original model required an M3 nut, but I didn't have one handy, so I reduced the hole size and simply used the bolt to...

I needed somewhere to mount my BL touch so modified this design. There's no adjustment so you just have to dial it in with the software offset (I use 3mm). I should add, i didn't like seeing the label on the fan so i modded it so it's the other way...

... close to the original position as possble. I was also able to put a BL-Touch closer to the nossle as the standart Ender 5 plus's position. I am not happy with the fan duct but it does the job for now. ... ...feel free to remix the sh** out of it.

I was in dire need of a BL Touch mount for my Anycubic Kossel that wouldn't collide with the rods and would only cover the upper half of the 40 mm hotend fan. After some careful consideration, I decided to design one myself. ...The resulting mount is...

This is a mount for a BL Touch on an A8 Plus. I had found a number of alternative methods, but all looked a little flimsy with a large cantilever. This is Easy to print Easy to mount Strong Integrated cable management I have produced two versions:...

This is a customized BL touch mount specifically designed for the SainSmart Pioneer 3D printer, which has its roots in the Xvico Pioneer. ... Here are the offsets that have been set in Marlin for my setup: #define X_PROBE_OFFSET_FROM_EXTRUDER -42 // X...

This innovative mount is equipped with several essential components: * A Built-in BL Touch Module for precise calibration * A Standard Fan Duct for optimal airflow * A Standard Fan Mount for easy fan installation * A T-Slot for future add-ons, such...

This is a custom BL Touch mount designed for Prusa i3 x carriages, specifically tailored to accommodate bowden setups with modified E3D V6 hotends. To optimize the print process, lay the top mount surface directly over the bed, reducing unnecessary...

I needed somewhere to mount my BL touch so modified this design. There's no adjustment so you just have to dial it in with the software offset (I use 3mm). I should add, i didn't like seeing the label on the fan so i modded it so it's the other...

I get fed up of having to reset the Z offset each time i remove the fan shroud for cleaning/maintenance etc so i cut off the lugs that share the same screws so the BL Touch stays mounted when the fans are removed. ... The M5 bolt that sticks through the...

The adjacent part to secure the actual BL Touch sensor can be found here: https://www.thingiverse.com/thing:3148733 (adj-bltouch-mount-3D-wing.stl). Although it's not flawless, this mount enables attachment of the sensor to the printer itself. Two...

After spending many hours installing the new endstop, I started searching for a better solution until my replacement BL Touch Clone arrives. This is when I came up with a simple Z probe design that matches the original's form factor, so you won't...

This is a remix of - https://www.thingiverse.com/thing:2753151 This fits the BL Touch smart or the 3D Touch on the Wanhao I3 Plus or its offspring perfectly. Fits very snug between the DiiCooler and the EiiCooler, making it a tight squeeze. I...

The design includes a mount for the BL Touch from Antclabs and is compatible with almost all setups using a direct drive E3D Titan extruder, as well as most direct drive and bowden setups that were compatible with Tom114's original model. Nut traps...

Couldn't find a mount for my BL-Touch for this Hemera aluminum mount I brought on eBay so I designed one myself, this works quite well and uses the two screws to the left of the mount to attach. I've added both one with two holes and one with a...

I've also swapped the BL Touch mount to the improved v2 side, flipping it so the sensor faces inward and the cabling is on the outside, bringing it closer to the extruder. All credit goes to the original designers who made this possible. ... Marlin...

Briss fang Ender 6 Bl touch mount. Offset settings Marlin. +--- BACK ---+ | [+] | L | 1 | R <-- Example "1" (right+, back+) E | 2 | I <-- Example "2" ( left-, back+) F...

This Parts Fan Mount also has a BL Touch mount. Its just a little hard to remove the Revo nozzle but not impossible. The coordinates for the BLTouch are: X=0.38mm; Y=-42mm You need support for the BLTouch version. Screws needed: For...

I wanted to add a BL Touch to my Sparkcube, so I printet this Model:https://www.printables.com/model/173295-sparkcube-filament-fan-holder-railBut that did not work because it was not for the modified xcarriage I am...

BL Touch (and clones) support for Flying Bear Ghost 5 stock print head. You can mount it and keep the full print area. It hides behind the motor and besides the fan. This is the 9th revision, there is a very little space to accomodate it, and...

I've always struggled with getting my BL touch dialled in precisely, so I sought out a solution that could be adjusted from the top with just one turn of the screw. Either a spring over the M4 screw and printing a dial for the top would work, or...

... to make the design a little less bulky. Added some thickness to BL Touch Mount. Weight of original is 82.1g, this remixed version printed for me at 64.6g. ... V2.2 has been refined a bit extending some screw holes and adding a few chamfers.

Could never get my BL touch dialled in so I wanted something I could adjust from the top with a single turn. You could use either a spring over the M4 screw and print a dial for the top, or use elastic bands as I have to keep the tension. Update I no...

Briss fang Ender 6 Bl touch mount. Offset settings Marlin. +--- BACK ---+ | [+] | L | 1 | R <-- Example "1" (right+, back+) E | 2 | I <--...

I'm a huge admirer of the Prusa MK3 extruder, so I decided to make some fundamental alterations to it in order to swap the proximity sensor with a BL-Touch. This was absolutely necessary for my large-format Prusa build, as it features a custom bed...