cr touch vs bl touch 3d models

https://www.thingiverse.com/thing:2759439This mount is shortened and adjusted to bring the CR Touch closer to the bed compared to the original.The original design did not get my CR Touch close enough to detect the bed, this design should fix that for...

https://www.thingiverse.com/thing:2759439 This mount is shortened and adjusted to bring the CR Touch closer to the bed compared to the original. The original design did not get my CR Touch close enough to detect the bed, this design should fix that...

This mount took inspiration from the mount included with the CR-Touch that fits with the Ender3.This model uses the same dimensions as the parent remix, however it was made fresh in Tinkercad...

I liked the shroud I found by chubbyzook (thing: 4821813). ...So, when it was time for a CR Touch, I remixed this design.

This Bracket is specifically designed for this direct drive. ...print with the open slide slot for the CR Touch wiring on the build plate to save using supports

CR Touch sensor mount and spacer. ... The center of the holes are 18mm distant and the holes are 1,5mm of radius (3mm of diameter).

... SealthySwiss doesn't work with CR Touch due to the location of the connector, and has a tendancy to bend even if printed in ABS. ... I clearanced it for the CR Touch connector, added strengthening braces, and tightened the clearance to the fan shroud.

3mm lower BL Touch and some material reduction on the top to better fit in place

Wanted something simple yet effective at blocking the LED, fits BL_Touch perfectly.

The optimal choice featuring a BL-touch allows seamless printing using a 3D printer.

All-in-One Printer with Built-In Fan and Advanced BL Touch Technology

Direct head for ENDER 6 with E3Dv6 and two 4010 + BL touch

A bracket for the TITAN direct drive extruder to have bl touch compatibilities.

This is a generative designed holder for the BL touch sensor. ...Its ultra light.

The BL touch set is now configured specifically for use on an Ender 3/5.

Upgraded to M2 with a BL Touch probe and it's working flawlessly.

Ender 3 Max Bl touch bracket customized to be stronger and not flex

This mount is for the CR Touch paired with the Spider 3.0 hotend.Z Offset = -2.65 (Your Value may differ, start at 0 offset to be safe)Y Offset = 0.0X Offset = 31.3

We're going to add a BL Touch to the Creality CR-X by using printed parts with M3 threaded rods and square nuts. ... To get started, you'll need: M3x6 threaded rods - 2 M3x8 threaded rods - 2 M3 square nuts - 2 You might also require shims, which can...

<p>I had been using a satsana shroud I found over on thingiverse by chubbyzook (Thing: 4821813). ...I couldn't find one with the propper CR Touch mount, so I remixed the one I was already using.Print with supports touching buildplate

I remixed the Support Touch-mi CR-10 from Thingiverse (https://www.thingiverse.com/thing:3350748) for my own CR-10S printer. ...I made the X-axis cart a bit larger, about 2mm more than usual, and also modified the magnet holder so it doesn't spin...

I've fixed the original mount from 3diwell website, so now it perfectly fits any BL-touch or 3D-touch sensors.

Cover with BL Touch or 3D Touch integrated. The original was 3 mm to low, therefor I made this remix. ...Sensor is 40 mm.

Simple yet effective bl-touch mount for creality ender 3 v2 (becouse one that came with bl-touch fits only ender 3 v1). No need for additional parts, nuts or screws. ...Works perfectly with original set of screws.

Another iteration, incorporating a BL Touch mount this time around. ...Note that the design for the BL Touch placement was derived from existing fan duct configurations, as ownership of the actual sensor was not within my control.

BL Touch Mount Optimized for Anycubic 4Max After Collaborative Tweaking with BMG and E3D. ... Following a joint effort between BMG, E3D, and our own team, we successfully integrated the BL Touch into the Anycubic 4Max 3D printer.

My adaption for a bl touch holder, mounts off the custom backplate i made for Anet a8.

This is a BL-Touch mount for the Wanhao i3 Plus MK2, it's mounted where the official sensor was.

Side mount for Hydra Fan Duct with BL-Touch and platform for strong cable ties. ... Actually UNTESTET...

i edit the level sensor holder so that the layout hole layout fit to the original BL Touch